Datasheet

File Name:HBG-60P-SPEC 2018-01-11
SPECIFICATION
HBG-60P series
MODEL
OUTPUT
VOLTAGE RANGE
Note.3
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT
OVER TEMPERATURE
90 ~ 295VAC 127 ~ 417VDC
47 ~ 63Hz
COLD START 45A(twidth= s measured at 50% Ipeak) at 230VAC100μ;Per NEMA 410
<0.75mA / 277VAC
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
ψ99mm *26mm (D * H)
ENVIRONMENT
SAFETY &
EMC
PROTECTION
EMC IMMUNITY
EMC EMISSION 8Note.
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
TOTAL HARMONIC DISTORTION
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC full load@
(Please refer to " " )POWER FACTOR (PF) CHARACTERISTIC section
THD< 20%(@load 65%/115VC,230VAC; @load 75%/277VAC)≧≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
WORKING TEMP.
Ta=-40 ~ +70 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
±5.0%
20% max. @rated current
0.21Kg; 32pcs/ 7.7Kg/ 0.68CUFT
60W Constant Current Mode LED Driver
RATED CURRENT
RATED POWER
CURRENT ADJ. RANGE
SET UP TIME
Note.4
CURRENT TOLERANCE
CONSTANT CURRENT REGION Note.2
OPEN CIRCUIT VOLTAGE(max.)
CURRENT RIPPLE
500ms / 230VAC 1200ms / 115VAC
HBG-60P-1050P
HBG-60P-1400P
HBG-60P-2100P
1050mA
1400mA
2100mA
680 ~ 1050mA
910 ~ 1400mA
1360mA ~ 2100mA
37 ~ 55V
28 ~ 43V 19 ~ 29V
60V
50V
35V
57.75W
60.2W
60.9W
90%
89% 89%
0.7A/115VAC 0.4A/230VAC 0.3A/277VAC
Ul8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1 & EN61347-2-13, EN62384, GB19510.14,GB19510.1 independent,EAC TP TC 004 approved
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C ( 65%) ; EN61000-3-3 EAC TP TC 020@load≧
,
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level( ) EAC TP TC 020surge immunity:Line-Line:2KV ,
1504.1K hrs min. Telcordia SR-332 (Bellcore) ; 452Khrs min. MIL-HDBK-217F (25 )℃
Shut down o/p voltage, re-power on to recover
Hiccup mode, recovers automatically after fault condition is removed
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.℃
2. Please refer to "DRIVING METHODS OF LED MODULE".
3.
De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected
by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
7. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com