iThermo4All Programmable Thermostat User Manual
Instructions for the installer...............................................4 Warranty............................................................................4 iThermo4all.......................................................................5 Placement..........................................................................5 Installation.........................................................................6 First time setup..................................................................9 Info...
Instructions for the installer Carefully read the instructions contained in the document that provide important information regarding the safe installation, usage and maintenance. After removing the packing, check the integrity of the unit. The system must be responsive to current safety standards. The manufacturer can not be held responsible for any damage caused by improper and erroneous usage. For repairs contact a service center authorized by the manufacturer.
iThermo4all The programmable thermostat iThermo4all has been designed to ensure ideal temperature conditions at any time of the day and for each day of the week. The installation takes a few minutes and requires a connection to the power supply (90-200Vac) and the connection to the air conditioning. Once installed and powered please refer to the section "First time setup” of this manual.
Installation Open the unit, remove the terminal cover and set the thermostat to the wall or on a mounting box using the appropriate screws.
LEGEND Power supply wire L = phase N = neutral Relay contact C = Common NO = normally open contact Load U1 = burner, pump, valve, etc.. Replace the terminal cover. Close the unit, making sure to insert the hooks into the seats.
Power Supply The power supply must be alternating current between 90 and 220V, 50/60Hz. WARNING! Wrong connection of the power supply can severely damage the unit.
First time setup When you turn on the thermostat, it issues a double beep if it is configured to create a own network (default) or a single beep if it is configured to access to the home network. After a few seconds you will hear another beep to indicate that the thermostat is ready to operate. If turning on you hear a double beep, you can proceed with the configuration of the parameters to make sure that the thermostat connects to your network.
Once you are ready, follow the instructions depending on the type of software used. iPhone Download the software from the iTunes Store. Connect to the network "iThermo4all" and launch the app. You will now see the settings of your thermostat. Enable the "Network" tab and select the label at the top “Network": the display shows all the fields to configure the thermostat, so that it can connect to your wifi network.
figure the thermostat to allow it connecting to your wifi network. Fill in the appropriate fields and press “Send". At this point, the thermostat will beep and will try to connect to your network. Exit the application and reconnect to your network and relaunch the program. If you have not used the DHCP you will be already able to view settings. If you are using DHCP, go to the "Network" tab and press the button “Find Device".
Settings This tab allows you to set the parameters of functioning of the thermostat. Iphone The first four buttons allow you to select the operating mode of the thermostat: • Manual Mode: maintains the set temperature independently of day and time. • Automatic mode: uses the set weekly programming (see next chapter). • Jolly Mode: uses the set jolly programming (see next chapter). • Holiday Mode: allows you to set a constant temperature for a specified number of days.
mode. By selecting the Holiday mode, fields appear to set degrees and number of days for which keep constant the temperature. Once the set days have passed, the thermostat automatically switches in Jolly mode. Example of use: if you plan to leave on saturday and return next saturday, set the number of days 6 and the temperature (ex 10°C).
• The "Advanced" button allows you to set special parameters of the thermostat: the field delta (thermic differential) allows you to set in tenth of degrees (from 0 to 9) the range of activation / deactivation. Example: if we set value to 0 and the set temperature is 20°C, winter mode shutdown will occur at 20.1 ° C and the activation at 19.9 ° C. If we set the field to 2, the shutdown will be at 20.3°C and the activation at 19.7°C.
Once you have modified the parameters, use the "Send" button to record the new values. When sending parameter is also set the date and time of the thermostat. Setting date and time To set the date and time, simply press the "Send" button in the parameter settings (tab "Settings"), even if no parameter is not changed. The date and time sent to the thermostat are the same of the iPhone.
mode, you disable the setting temperature field and activate the set programming (see next chapter). By selecting the Jolly mode, you disable the setting temperature field and activate the set programming (see next chapter). The Jolly mode is a particular mode of Automatic functioning, valid only for the day in which it is active. At 11:59pm the thermostat switches to the Automatic mode. By selecting the Holiday mode, fields appear to set degrees and number of days for which keep constant the temperature.
the device will turn on for temperatures higher than the one set. • The "Web Connection" button allows you to activate / deactivate the sending of the operating data of the thermostat to the website. Disabling the button will NOT be possible to control the thermostat via the website (see the chapter "The Website”).
way the reading having available a tool to detect the temperature. This field allows to specify a value in degrees (from -9.0 ° C to +9.0 ° C) that will be added or subtracted, according to the sign, to the value of the temperature. Once you have modified the parameters, use the "Send" button to record the new values. When sending parameter is also set the date and time of the thermostat.
you want to delete and press "Delete Selected" button or the "Clear All" button to clear all schedules. • To change a schedule or add a new one use the "Edit" button.A group of elements will appear on the screen, they allow you to set the date, time and temperature. In the field “Day” you can select the days of the week and also the value “Mon-Fri" that allows you to set the time and temperature automatically for every day from Monday to Friday. Other values you can select are “Sat-Sun" or "Every Day.
• To change a schedule or add a new one, set the values in the checking box. In particular, in the field “Day” you can select the days of the week and also the value “Mon-Fri" that allows you to set the time and temperature automatically for every day from Monday to Friday. Other values you can select are “Sat-Sun" or "Every Day." Once you have set the desired values press the "Add" button (+) to include them in the list.
button through the hole. A double beep will indicate that the thermostat is in “adhoc" mode. After activating the “adhoc” mode, to see if the thermostat communicates, press the "Update" button, you will read "Connected" if yes or "device not found" if the sensor is not communicating. • The "Network" button allows you to set the parameters of your network so that the thermostat can connect to the same. The "Network Name" and “Password" fields are case sensitive.
you receive a message that require the update of the list. If you update the list, all the previous information are deleted. Each element of the list shows the name of the thermostat and its IP address; in order to communicate with a specific sensor, just touch the desired sensor. • The "Delete" button allows you to manually delete a sensor from the list. • -The "Edit" button (pencil) allows you to change the name of a thermostat on the list.
time of recording. When this time is expired, to be able to continue to use the remote management, you need to renew your subscription through the website www.ithermo4all.eu Windows • The "Update List" button allows you to update the list of thermostats are connected to your network. Using this function is performed a scan of the thermo were present on the network.
on www.ithermo4all.eu. After recording the sensor, you can also remotely control the thermostat through the site: www.ithermo4all.eu The purchase of each thermostat includes the use of the remote management for a period of 12 months from the time of recording. When this time is expired, to be able to continue to use the remote management, you need to renew your subscription through the website www.ithermo4all.eu Website The website for the management of the thermostat is located at the web address: www.
server and will remain synchronized with the time changes.For all other settings, you can refer to the instructions of the applications.Once you save a change, it will not be performed immediately, but will remain in a queue until your thermostat will query our server to check if there are any changes to load. In the “information” tab, at the bottom of the list, you can see the number of pending changes.
Specifications • • • • • • • • • • • • • • • Device for civil use. Electronic device independent mounting. Power supply: 90-220Vac 50/60Hz Relay: 250V maximum voltage, 5A maximum current with resistive load (2A inductive load). 4 operating modes: Manual, Automatic, Jolly, Holidays Setting range: from +5°C to +40°C. Programming: 24 temperature levels for each day of the week. Detection range temperature: 10 sec. Differential: from ± 0.1°C to ± 0.9°C. Temperature correction: ± 9°C Display Resolution: 0.1°C.
Disposal and recycling All electrical and electronic equipment must be disposed of separately from general household waste using the sites designates by local authority. If a product display this symbol of a crossed-out rubbing bin, the product is subject to European Directive 2002/96/EC. For further information on disposing of your used equipment, please contact your local authority, your refuse collection service or the dealer you purchased the product from.
MDV Ingegneria Elettronica Castel Guelfo - BO - Italy Version 0.9 www.ithermo4all.eu www.mdvbologna.
