Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
MX-2100/2104 Installation and Operation Manual Chapter 2 Installation
Initial Setup and Configuration 2-21
2.7 Initial Setup and Configuration
When starting a management session for the first time, it is recommended to
prepare MX-2100 for communication with the supervision terminal as explained
below. The preparations include the setting of switch SW2/3 on the KCL.2 module
(refer to KCL.2 Module on page 2-14 for more information), and the connection of
the terminal to MX-2100 (refer to Interfaces and Connections on page 2-16 for
more information).
Internal MX-2100 Settings
The default settings of all the sections of the switch SW3 on the KCL.2 module are
OFF. To ensure successful establishment of communication with the terminal, you
may need to change the settings of the PSWRD section, switch SW3 in section 3.
In general, you must enter a password when you start a management session. If
the password is incorrect, MX-2100 will not respond. The PSWRD section is used
to restore the default MX-2100 password (RAD).
With this section in the OFF position, you can define your own communication
parameters, password. To change to the default values, set the sections to ON, and
then press the RESET push-button of the KCL.2 module (if not, the change will
take effect the next time MX-2100 is turned on). The default values are then
loaded and stored.
After performing this procedure, return the switch sections to OFF.
Supervision Terminal
Configure the terminal for the communication parameters you selected for the
MX-2100 SP port (default values are listed above), select the full-duplex mode,
and turn terminal echo off.
Connections
Refer to Interfaces and Connections on page 2-16.
After making the required connections, turn the supervision terminal on. When
applicable, also turn on the modems and any other communication equipment
used to connect the terminal to MX-2100.
Initial Configuration
The prompt PASSWORD> indicates that password protection is enabled, and you
must enter the current password to proceed. However, if you set the PSWRD
section of the DIP switch to ON, a null password and node address is used,
therefore after pressing ENTER you will obtain the working prompt.
Press ENTER several times to see the working prompt of MX-2100, which is by
default >.
After the MX-2100 prompt is displayed on the terminal, define the terminal
control sequences using the command F
or using the command init F[].
Refer to the Command Set Description appendix for more information. Typical
terminal control sequences are given in the following table.