Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Quick Start Guide MX-2100/2104 Installation and Operation Manual
2 Controlling MX-2100 from a Supervisory Port
4. If MX-2100 includes a KM-Ringer module, turn it on by setting its POWER
switch to ON. Verify that the RING VOLTAGE and BATTERY VOLTAGE
indicators light.
5. Check the MX-2100 configuration (refer to Checking Current Operating
Configuration in the Operation chapter).
6. Check the normal MX-2100 operating indications (refer to Normal Indications
in the Operation chapter).
7. MX-2100 has diagnostic functions which can be used to test the proper
operation of the MX-2100 system and identify the faulty components. For an
explanation of the MX-2100 diagnostic functions refer to the Diagnostics
chapter.
8. Turn off MX-2100 as follows:
- If MX-2100 includes a KM-Ringer module, then turn off the
KM-Ringer before MX-2100.
- For the MX-2100’s KPS modules and MX-2104,
set the ON/OFF switches (on the rear panels) to OFF.
3. Setting-Up the Local Configuration
To set-up the MX-2100 local configuration (for more detailed information refer to
Setting Configuration Parameters in the Configuring MX-2100 chapter):
1. Set the system parameters refer to Configuring the System Parameters in the
Configuring MX-2100 chapter).
2. Select the main link parameters (refer to Configuring the Main Link Parameters
in the Configuring MX-2100 chapter).
3. Select the channel parameters (refer to Configuring the Channel Parameters in
the Configuring MX-2100 chapter).
4. Controlling MX-2100 from a Supervisory Port
To control MX-2100 from a supervisory port (for more detailed instructions refer to
Operating Instructions in the Operation chapter):
1. Start a session for MX-2100 (refer to Starting a Session - Single MX-2100 and
Starting a Session - Multiple MX-2100 in the Operation chapter).
2. Type the desired commands after the working prompt and press Enter to
execute the command. Refer to the Command Set Description appendix for a
list of commands available.
3. End the control session by typing EXIT. You can now control MX-2100 from
the front panel (refer to General Front Panel Operating Instructions in the
Configuring MX-2100 chapter).