Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
MX-2100/2104 Installation and Operation Manual Chapter 1 General Information
Physical Description 1-13
• KVC.1M - ADPCM or PCM voice interface module, provides one or two voice
channels and support error-free fax transmission. For more information, refer
to the KVC.1M Installation and Operation Manual.
The following versions are available:
− KVC.1M/E&M: two voice channel with four-wire or two-wire interface with
E&M signaling per RS-464 Types I, II, III and V, and British Telecom SSDC5
− KVC.1M/E&M48: similar to the KVC.1M/E&M, except that it requires an
external -48 VDC source to supply the signaling voltage for increasing the
maximum allowed line length
− KVC.1M/FXS: two voice channels with two-wire interface for direct
connection to a telephone set
− KVC.1M/FXSP: similar to KVC.1M/FXS, except that it has an internal ringer
and line feed supply
− KVC.1M/FXO: two voice channels with two-wire interface and FXO loop
start signaling for direct connection to a PBX extension line.
• KVC.3 - Low-bit rate voice module, provides two high-quality compressed
voice channels. For more information, refer to the KVC.3 Installation and
Operation Manual.
The following versions are available:
− KVC.3/E&M: two voice channels with four-wire or two-wire interface with
E&M signaling per RS-464 Types I, II, III and V, and British Telecom SSDC5
− KVC.3/FXS: two voice channels with two-wire interface for direct
connection to a telephone set
− KVC.3/FXSP: similar to KVC.3/FXS, except that it has an internal ringer and line
feed supply
− KVC.3/FXO: two voice channels with two-wire interface and FXO loop start
signaling for direct connection to a PBX extension line.
• KLS.1 - Low-speed RS-232 data module. For more information, refer to the
KLS.1 Installation and Operation Manual.
• KLS.2 - Low-speed RS-232 four-channel asynchronous statistical data module.
For more information, refer to the KLS.2 Installation and Operation Manual.
• KHS.1 - High-speed data interface module, provides two high-speed V.35,
RS-530 or RS-449/RS-422 data channels. For more information, refer to the
KHS.1 Installation and Operation Manual.
• KHS.2 - Two-channel synchronous data module. For more information, refer
to the KHS.2 Installation and Operation Manual.