Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Chapter 1 General Information MX-2100/2104 Installation and Operation Manual
1-12 Physical Description
Option Modules (not for MX-2104)
The 3U MX-2100 system can accept two types of options module:
KAI
Alarm indication module for installation in the options position, or in any I/O slot.
The KAI includes indicators similar to those located on the MX-2100 front panel.
These indicators repeat all the relevant MX-2100 front panel indications on the
rear panel, and thus complement the indicators available on the rear panels of the
other modules. Maintenance activities are thus expedited, as all the MX-2100
indications become readily available on one side of the equipment.
KDI
Bypass and multidrop module. The KDI module can be installed in the option slot,
or in any I/O slot. The KDI module enables direct transfer (bypassing) of a group of
main link frame bits, in both directions, between the two main links of MX-2100.
Channels that are not bypassed are connected to I/O modules of MX-2100.
The KDI module is available in two versions:
• KDI version: supports only the bypassing function
• KDI/M version: also includes a data channel interface for one multidrop channel.
The multidrop channel is compatible with the data channels of the KLS.1/NEW
low-speed data module, and supports data rates in the range of 0.3 to 64 kbps. As
is standard practice in a multidrop application, the receive path of the local
multidrop channel continuously receives the data transferred in its allocated
bandwidth on the desired main link (the same data is also bypassed to the other
link, to make it available downstream), but its transmit path is connected to the
main link only when the RTS line in the local interface is asserted.
For more information, see the option module’s Installation and Operation Manual.
I/O Modules
MX-2100 supports up to 12 user-selected I/O modules. MX-2104 supports up to 4
user-selected I/O modules. Both units can accept any combination of the following
types of I/O modules with power supply limitations.
KVC.1 - ADPCM or PCM voice interface module, provides two voice channels. For
more information, refer to the KVC.1 Installation and Operation Manual.
The following versions are available:
− KVC.1/E&M: four-wire or two-wire interface with E&M signaling per
RS-464 Types I, II, III and V, and British Telecom SSDC5
− KVC.1/FXS: two-wire interface for direct connection to a telephone set
− KVC.1/FXO: two-wire interface for direct connection to a PBX extension
line.