Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Chapter 1 General Information MX-2100/2104 Installation and Operation Manual
1-6 Physical Description
• Using a network management station or TELNET via a SLIP connection to the
remote MX-2100. The remote MX-2100 requires an IP address. For
information on assigning an IP address, refer to the DEF AGENT command in
the Command Set Description appendix.
• Using an ASCII terminal via a modem connection to the SP port.
Diagnostic Capabilities
The MX-2100 system provides extensive diagnostics, supervision and maintenance
capabilities for easy maintenance and rapid detection and location of faults.
MX-2100 diagnostics include automatic self-test upon power-up, and on-line
monitoring of critical functions. The system generates time stamped alarm
messages that cover all the significant system events. The time stamp is provided
by a real-time clock with battery backup. The system operator can then perform
comprehensive testing on each type of module, to determine the cause of the
alarm messages and return the system to normal operation.
Various types of test loops are provided, including modem loops 2 and 3 per
ITU-T Rec. V.54 for rapid isolation of the fault area, tone injection for rapid testing
of voice interface modules, and pseudo-random sequence transmission test for
checking the proper operation of data interface modules, and detection of bit
errors.
1.2 Physical Description
MX-2100, General Description
The MX-2100 system consists of a 19" (3U) enclosure that contains 18 module
slots. Five of the slots (slots 1 through 5) are assigned to the system modules:
• The control subsystem
• The main link (aggregate) interface subsystem
• The system power supplies.
Two slots each are assigned for KML and KPS modules, respectively, to provide
support for the redundancy option:
• Slots 1 and 2 - for KPS modules
• Slots 3 and 4 - for KML modules.
One slot (slot 6) is assigned for an options module (e.g., for the KDI or KAI
modules). The other 12 slots are intended for I/O modules. Each I/O slot can
accept any type of I/O module. All the modules are inserted through the rear
panel. The cable connections are also made through the rear panel.
Figure 1-3 shows a general view of a MX-2100, and identifies the functions of the
enclosure slot.