Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Appendix F Command Set Description MX-2100/2104 Installation and Operation Manual
F-36 Commands
• CONTROL SIGNALS - Displays the control signal support mode for the
corresponding channels. The following codes can appear:
LOCAL - Channel configured for local control signal support (data
channel only).
RTS - Channel configured for end-to-end transmission of RTS line state
(data channel only).
DTR&RTS - Channel configured for end-to-end transmission of DTR
and RTS lines states (data channel only).
SIGNALING - Channel configured for end-to-end transmission of E and
M signaling (voice channel only).
N/A - Not applicable: displayed in lines with COMP i:*.
DSP FLIP
Purpose
Display the cause of the last switching (flip) from one main link to the other.
This command is accepted only when MX-2100 operates in the switched backup,
priority bumping, or redundancy mode.
Format
DSP FLIP
Use
• Type:
DSP FLIP <ENTER>
The following message is displayed:
LAST FLIP CAUSED BY: 'cause'
The following 'cause' descriptions can be displayed:
NO FLIP - No flip occurred.
FORCED FLIP - Flipping occurred as a result of operator's command
(FLIP ML).
ML CTS OR DSR IS OFF - Flipping occurred because the CTS or DSR
line in the interface of the KML module serving the previously used link
had been switched off by the modem. This cause can appear only
when the DSR&CTS main link parameter is set to EXT.
ML HARDWARE FAILURE - Flipping occurred after a hardware failure
has been detected in the KML module serving the previously used link.
ML LOCAL SYNC LOSS - Flipping occurred because the local KML
module serving the previously used link lost frame synchronization.
ML REMOTE SYNC LOSS - Flipping occurred because the remote KML
module serving the previously used link lost frame synchronization.
ON LINE ML REMOVED - Flipping occurred because the KML module
that was previously on-line has been removed from its slot.