Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
MX-2100/2104 Installation and Operation Manual Appendix F Command Set Description
Commands F-27
The password entry screen appears, e.g.,
NEW PASSWORD (4 to 8 CHARS) =
CURRENT PASSWORD = 'password'
2. Type the required password (spaces are recognized as valid characters in a
password).
The password appears on the second line.
3. Carefully check that the specified password has been indeed typed in, and
then press ENTER.
The new password takes effect, and the MX-2100 prompt reappears.
DEF ROUTE
Purpose
Enables static routing of management information to network devices that do not
support the proprietary RIP routing protocol used by the MX-2100. The IP
addresses of such devices should be defined here.
By using this command you can declare an IP address on the list as an Ethernet
address. When an agent searches for this IP address, it will be directed to the
Ethernet.
Format
DEF ROUTE
Use
• Type:
Def route <ENTER>
The MX-2100 displays the following data form:
KM2100>def route
CURRENT ROUTE PARAMETERS
-------------------------
ROUTE IP ADDRESS 1 IS :000.000.000.000
ROUTE IP ADDRESS 2 IS :000.000.000.000
ROUTE IP ADDRESS 3 IS :000.000.000.000
ROUTE IP ADDRESS 4 IS :000.000.000.000
ROUTE IP ADDRESS 5 IS :000.000.000.000
ROUTE IP ADDRESS 6 IS :000.000.000.000
ROUTE IP ADDRESS 7 IS :000.000.000.000
ROUTE IP ADDRESS 8 IS :000.000.000.000
ROUTE IP ADDRESS 9 IS :000.000.000.000
ROUTE IP ADDRESS 10 IS :000.000.000.000
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999
ROUTE IP ADDRESS :999.999.999.999