Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5orDSP PBX
- DSP KVF6
- DSP SIGNALINGorDSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection

Chapter 1 General Information MX-2100/2104 Installation and Operation Manual
1-4 Functional Description
System Supervision and Configuration
The MX-2100 system is designed for unattended operation. A complete collection
of operating parameters configures the MX-2100 system and each of its modules.
This collection of operating parameters is determined by a database. This database
is stored in the non-volatile memory of the MX-2100 control module. MX-2100
can store two different databases, and can be configured to switch automatically
between the databases, in accordance with a predetermined daily schedule
("day/night" operation), or to use one of the databases only in case of switching to a
backup link.
MX-2100 supervision and minimal configuration functions can be performed from
its front panel, using three push-buttons and an LCD display. For more detailed
information, refer to Local Management on page 1-33.
MX-2100 stores alarms detected during operation in a buffer. The buffer serving
the front panel LCD can store one alarm of each type. The buffer for alarms to be
sent to a supervision terminal can hold up to 100 alarms. During regular operation,
a front panel indicator lights to indicate if there are any alarms in the alarm buffer.
The local operator can then review the contents of the alarm buffer on the front
panel LCD display, and can delete old alarms related to events that are no longer
present in the system.
In addition to the alarm buffer, the front-panel LED indicators display in real time
the main link and power supply status and alert when test loops are present in the
system. The front panel LED indicators can also be used to monitor on-line a
selected user channel. The monitored functions are transmit and receive data
activity, and the state of the RTS and DCD control lines (or E and M lines for voice
channels).
Local MX-2100 Management
A local MX-2100 can be managed by any of the following:
• MX-2100 front panel using push buttons and an LCD
• ASCII terminal connection to the local MX-2100
• TELNET connection to the local MX-2100. The connection can be via SLIP or
via an Ethernet LAN. The local MX-2100 requires an IP address. For
information on assigning an IP address, refer to the DEF AGENT command in
the Command Set Description appendix.
• SNMP network management station connected to the local MX-2100. The
connection can be via SLIP or via an Ethernet LAN. The local MX-2100
requires an IP address. For information on assigning an IP address, refer to the
DEF AGENT command in the Command Set Description appendix.
Remote MX-2100 Management
A remote MX-2100 can be managed either in-band or out-of-band. For both, the
remote MX-2100 requires an IP address. For information on assigning an IP
address, refer to the DEF AGENT command in the Command Set Description
appendix.