Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Appendix F Command Set Description MX-2100/2104 Installation and Operation Manual
F-8 Commands
3.
Continue until all the parameters are defined, and then press ENTER to end.
A typical display, as seen after all the parameters are selected, is shown
below:
CURRENT AGENT PARAMETERS
--------------------
IP ADDRESS IS : = XXX.XXX.XXX.XXX
SUBNET MASK IS : = XXX.XXX.XXX.XXX
DEFAULT GATEWAY IS : = XXX.XXX.XXX.XXX
READ COMMUNITY IS : = public
WRITE COMMUNITY IS : = private
TRAP COMMUNITY IS : = public
where X stands for the digits for the current IP address, Subnet Mask and
Default Gateway.
The agent parameters displayed on the data form, and their range of values, are as
follows:
• TELNET_APATHY_TIME - Press the F or B key to select the time (in minutes)
after which a TELNET connection will automatically be terminated if no
incoming activity is detected. The available values are 10MIN, 15MIN and
20MIN.
• IP_ADDRESS - Type the IP address assigned to the SNMP agent in the
dotted-quad form (four groups of digits ranging 0 through 255, separated by
periods).
• SUBNET MASK - Type in the subnet mask in the dotted-quad format. The
mask consists of four groups of digits in the range of 1 through 255, separated
by periods. The net section must consist of 1’s.
• DEFAULT GATEWAY - Type in the IP address assigned to the DXC SNMP
agent in the dotted-quad format (four groups of digits in the range of 0 through
255, separated by periods).
• READ COMMUNITY - Type the name of the SNMP community that has
read-only authorization. The SNMP agent will accept only getRequest and
getNextRequest commands from management stations using that
community. You may enter up to seven alphanumeric characters.
• WRITE COMMUNITY - Type the name of the SNMP community that has
read-write authorization. The SNMP agent will also accept getRequest
commands from management stations using that community. You may enter
up to seven alphanumeric characters.
• TRAP COMMUNITY - Type the name of the SNMP community to which the
SNMP agent will send traps. You may enter up to seven alphanumeric
characters.