Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Appendix B Alarms MX-2100/2104 Installation and Operation Manual
B-16 Configuration Error Messages
ERROR 209 CHANNEL SOURCE OF MASTER/FALLBACK CLOCK DOES NOT EXIST
You are trying to select a channel that is not physically present as the clock source.
ERROR 210 INVALID ML-B CARD TYPE FOR SWITCH BACKUP ML MODE
You can select the switched backed mode only when a KML.1, KML.2, KML.3 or
KML.10 module is installed.
ERROR 211 ML MODE NOT COMPATIBLE WITH NO. OF ML
Before selecting the dual-link or priority bumping mode, make sure to configure
two links.
ERROR 212 CONNECTED MUXES SHOULD HAVE THE SAME NO. OF
CONFIGURATIONS
For two MX-2100 connected in a link, always define the same number of data
bases (either one or two data bases on each unit).
ERROR 213 KM2104 CAN HAVE ONLY ONE LINK
You are trying to define a second link on a MX-2104. This is not supported.
ERROR 214 LOCAL-REM SLOTS OP. HIGHWAY OR ML PRIORITIES,
INCOMPATIBLE
Check configuration of main link priorities for all the modules.
ERROR 215 KM2104 OFFSET, EDIT-AGENT MISMATCH
The current offset and the offset in the edited data base are different.
ERROR 218 ONLY ONE KDI/KDI.CH IS ALLOWED IN A MUX
Only one KDI or KDI/CH can be installed (or programmed) in a MX-2100.
ERROR 226 ML BITWEIGHT MISMATCH
When performing manual frame allocation, the two MX-2100 connected in a link
must have equal bandwidth allocation units (refer to the General Information
chapter).
ERROR 234 KVF.5 SLAVE CARDS MUST HAVE A MASTER
Make sure a KVF.5/T1/M or KVF.5/E1/M module is installed.
ERROR 235 TOO MANY KVF.5 CARDS IN THE MUX
The total number of KVF.5 modules inserted in the MX-2100 exceeds the
maximum number needed to process the T1 or E1 signal.
ERROR 236 INVALID KVF.5 TS GROUP
You are trying to select an incorrect group of time slots on a KVF.5 slave module.