Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Appendix B Alarms MX-2100/2104 Installation and Operation Manual
B-14 Configuration Error Messages
ERROR 39 ILLEGAL COMMAND FOR CURRENT SYSTEM TYPE
The command entered by you is not supported by the MX-2104.
ERROR 41 ILLEGAL COMMAND NO CONNECTED CHANNELS
You are trying to enter a command that is supported only when the channel
specified in the command is connected.
ERROR 42 CONFLICT IN FRAME MODE AND DOWNLOAD
You can select manual frame bit allocation only when downloading is disabled.
ERROR 43 ILLEGAL FRAME ALLOCATION
An incorrect bit allocation has been detected, i.e., the same bits have been
assigned to different channels, or the specified start or end bit number is invalid.
ERROR 44 ILLEGAL LINK CLOCK AND ML MODE COMBINATION
You can select the main link clock source only when using the dual-link or priority
bumping mode, provided a KDI module is installed in the MX-2100.
ERROR 45 ILLEGAL LINK CLOCK AND ML TIMING COMBINATION
When selecting one main link as the clock source, the timing mode of the other
main link cannot be DTE or LBT.
If both main links use LBT or DTE timing, the LINK_CLK parameter must be set to
NONE.
ERROR 50 ILLEGAL COMBINATION OF INTERFACE AND ECHO CANCELLER
You are trying to disable the echo canceller of a voice module, e.g., KVC.2, etc.,
when its interface is 2-WIRE. This is not allowable, because when the link
connecting between the subscribers includes hybrids, the quality of transmission
without echo cancellers is degraded.
ERROR 51 ML_MODE AND HARDWARE CONFIGURATION CONFLICT
The MX-2100 is equipped with only one KML module, but you are trying to select
a main link mode that requires two KML modules (i.e., only the SINGLE mode is
allowed).
ERROR 52 CONFLICT BETWEEN CH1 AND CH2 SPEEDS
• You are trying to configure channels 1 and 2 of a KLS.1 module to operate
with data rates from different groups. This is not allowed.
• For the KVF.4/S0 module, you cannot select a 64 kbps rate for both the B1
and B2 channel.
ERROR 56 ILLEGAL START TIME SLOT ALLOCATION
You are selecting an incorrect starting time slot on the KVF.5 master module.
ERROR 58 ILLEGAL SIGNALING MODE
You are selecting an incorrect signaling parameter in KVF.5 or KVF.6 modules.