Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
Appendix B Alarms MX-2100/2104 Installation and Operation Manual
B-12 Configuration Error Messages
ERROR 15 ILLEGAL LOOP COMBINATION INVOLVING ML V.54 LOOP3
You are trying to activate (on either MX-2100) an illegal combination of loops that
includes a main link ITU-T Rec. V.54 loop 3 (refer to the Diagnostics chapter).
ERROR 16 ILLEGAL KLS.2 COMPOSITE AND ML-<A or B> SPEED
COMBINATION
The MX-2100 main link rate is 256 or 384 kbps, and you are trying to configure a
KLS.2 module for a composite data rate of 2.4 kbps. This combination of main link
and composite data rates is not allowable, because it would require oversampling.
ERROR 17 ML MODE NOT COMPATIBLE WITH I/O SLOT LINK SELECT
The selected main link mode is not compatible with the selections made for the I/O
modules, i.e., some modules have been connected to main link A and others to main
link B, but the current main link mode is SINGLE, REDUNDANCY, or SWITCHED
BACKUP.
ERROR 18 TIMING/SPEED NOT COMPATIBLE WITH ML MODULE TYPE
You are trying to select a timing mode and/or speed that is not supported by the
installed KML module.
ERROR 19 ILLEGAL ML MODE FOR WORKING WITH LCD
The main link mode selected by the operator on the MX-2100 front panel is not
allowed, because the required parameters cannot be defined using the front panel
controls and the LCD.
ERROR 20 ILLEGAL COMMAND, MODULE NOT INSTALLED
The slot whose number has been specified in the command is empty.
ERROR 21 ILLEGAL COMMAND, CHANNEL IS DISCONNECTED
The channel whose number is specified in the command is not connected (NC).
You must connect the channel before specifying its number in a configuration
command.
ERROR 22 LOOP IS NOT ACTIVE
You are trying to deactivate a loop that currently is not activated.
ERROR 23 ILLEGAL LOOP FOR INSTALLED MODULE
The loop you are trying to activate is not supported by the module whose number
has been specified in the command.
ERROR 24 ILLEGAL COMMAND FOR CURRENT ML MODE
The command you have entered is not allowed in the current main link mode.
ERROR 25 CONFLICT BETWEEN CTRL_SIG PARAMETER AND MODULE TYPE
The value entered in the CONTROL SIGNALING field is not supported by the
module whose number has been specified in the command.