Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
MX-2100/2104 Installation and Operation Manual Appendix B Alarms
Alarm Messages B-5
Table B-1. LCD Alarm Messages (Cont.)
Code Message - LCD Message - Terminal Alarm
Type
Description
38 DSU LOOP.B DSU LOOPBACK,
SLOT i
State The KML.6 module installed in slot
(ML-A, ML-B) performs a DSU loopback
in response to a network DSU loopback
request
39 LINK ERROR KTRE/KMBE LINK
ERROR, SLOT i
State The KTRE or KMBE module installed in
I/O slot (1 through 12) of the local
MX-2100 unit has lost communication
with the remote side
40 LAN ERROR KTRE/KMBE LAN
ERROR, SLOT i
State The KTRE or KMBE module installed in
I/O slot (1 through 12) of the local
MX-2100 unit reports that the LAN
insertion process failed
41 KDI FRAME OVF KDI FRAME
OVERFLOW
Event Frame overflow occurred. This usually
happens because the timing of link A is
not locked to the timing of link B
42 PIGB HRD ERR PIGGY-BACK
HARDWARE ERROR A
State The KML.7 module installed in the
specified slot reports a hardware
problem on the T1 interface board
43 NETWORK LLB NETWORK LLB,
SLOT i
Event A network-initiated line loopback has
been activated. This loopback cannot be
disconnected by the system
management
44 NETWORK PLB NETWORK PLB,
SLOT i
Event A network-initiated payload loopback
has been activated. This loopback
cannot be disconnected by the system
management
45 DRIVER FAIL DRIVER FAIL,
SLOT i
State The KML.8 module installed in the
specified I/O slot reports a hardware
failure in the E1 line driver
46 SIGNAL LOSS SIGNAL LOSS, SLOT i State The KML.8 module installed in the
specified slot reports a loss of input
signal
47 EXECIVE BPV EXECIVE BPV, SLOT i State The number of coding errors detected in
the main link signal received by the
active main link module is too high (the
bipolar violation rate exceeds 1×10
6
for
1000 consecutive seconds). This may
indicate a fault in the link or in the link
transmission equipment, or a failure in
the active main link module
48 AIS OCCURED AIS OCCURED, SLOT i State The Alarm Indication Signal (AIS), a
framed “all ones” sequence, is received
on the main link