Specifications
Table Of Contents
- Preface
- Quick Start Guide
- Table of Contents
- Chapter 1 General Information
- Functional Description
- Physical Description
- Application Considerations
- Basic MX-2100 System
- Redundancy (not for MX-2104)
- Dual Link Operation (not for MX-2104)
- Priority Bumping \(not for MX 2104\)
- Switched Backup Operation (not for MX-2104)
- Switch Mode
- System Management
- System Timing Considerations
- DTE Timing (KML.1, KML.2, KML.3, KML.4 and KML.10 Modules)
- External DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- DCE Timing (KML.1, KML.2, KML.3 and KML.4 Modules)
- Internal Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- Loopback Timing (KML.5, KML.6, KML.7, KML.8, and KML.F Modules)
- DCE Timing (KML.7, KML.8, and KML.F Modules)
- Main Link Timing Considerations in Bypassing and Multidrop Configurations
- Data Channel Clock Modes
- Timing Modes of ISDN Channels
- Sub Link Timing
- Main Link Interface Characteristics
- V.35 Interface (Module KML.1)
- RS-232 Interface (Module KML.2)
- V.36/RS-422/RS-530 Interface (Module KML.3)
- X.21 Interface (Module KML.4)
- G.703 Codirectional Interface (Module KML.5)
- Standard DDS CSU/DSU (Module KML.6)
- T1 Link Interface (Module KML.7)
- E1 Link Interface (Module KML.8)
- ISDN "S" Interface (Module KML.10/S)
- ISDN "U" Interface (Module KML.10/U)
- Fiber-Optic Link Interface (Module KML.F)
- I/O Module Applications
- Technical System Characteristics
- Chapter 2 Installation
- Introduction
- Site Requirements and Prerequisites
- Input Power Requirements
- Grounding
- Channel Connection Considerations
- Front and Rear Panel Clearance
- Ambient Requirements
- Electromagnetic Compatibility Considerations
- Current and Power Requirements of MX-2100 Power Supply Modules
- Current and Power Capabilities of MX-2100 Power Supply Modules
- Ratings of Ring and Feed Voltage Supplies
- Equipment Needed
- Package Contents
- Installation and Setup of MX-2100
- Interfaces and Connections
- Initial Setup and Configuration
- Chapter 3 Configuring MX-2100
- Chapter 4 Operation
- Chapter 5 Diagnostics
- Appendix A Connection Data
- Appendix B Alarms
- Appendix C SNMP Management
- Appendix D Software Download
- Appendix E Configuration Parameters
- Appendix F Command Set Description
- General
- Commands
- BYE
- CLR ALM
- CLR LOOP
- CLR MONITOR
- CONNECT SWITCH
- DATE
- DEF AGENDA
- DEF AGENT
- DEF ALM DEBOUNCE
- DEF CALL
- DEF CH
- DEF CON
- DEF DB FLIP
- DEF DP
- DEF FRAME
- DEF MANAGER LIST
- DEF ML
- DEF ML CALL
- DEF NAME
- DEF NODE
- DEF NP
- DEF PWD
- DEF ROUTE
- DEF SP
- DEF SYS
- DISCONNECT SWITCH
- DSP AGENT
- DSP ALM
- DSP BERT
- DSP CH CON
- DSP FLIP
- DSP HDR TST
- DSP MANAGER LIST
- DSP KVF5 or DSP PBX
- DSP KVF6
- DSP SIGNALING or DSP SIG
- DSP PRBS_INJ
- DSP REM AGENT
- DSP REV
- DSP ST FRAME
- DSP ST ML
- DSP ST SLOT
- DSP ST SYS
- EDIT DB
- EXIT
- F
- FLIP ML
- HELP
- INIT DB
- INIT F
- LOAD DB 1\2
- LOAD IO
- LOOP
- ML RECOVERY
- MONITOR
- REBUILD FRAME
- RESET LOC
- RESET IO
- RESET ML
- TIME
- UPDATE DB 1\2
- Index
- DC Power Supply Connection
MX-2100/2104 Installation and Operation Manual Chapter 4 Operation
Operating Instructions 4-13
While the KCL module performs the power-up self-test, the supervision terminal
displays:
CL Board Self Test In Progress ....
After the self-test is completed, the result, OK or FAILED, is added to the
displayed line. MX-2100 starts reading the installed modules, and the supervision
terminal displays:
Reading Installed Modules .....
After the reading is completed, the state of the installed modules is displayed in
the following format:
SLOT 1 PS-A OK
SLOT 2 PS-B OK
SLOT 3 ML-A OK
SLOT 4 ML-B OK
SLOT 5 CL OK
I/O SLOT 1 I/O 1 OK
I/O SLOT 2 I/O 2 OK
I/O SLOT 3 I/O 3 OK
I/O SLOT 4 I/O 4 OK
I/O SLOT 5 I/O 5 OK
I/O SLOT 6 I/O 6 OK
I/O SLOT 7 I/O 7 OK
I/O SLOT 8 I/O 8 OK
I/O SLOT 9 I/O 9 OK
I/O SLOT 10 I/O 10 OK
I/O SLOT 11 I/O 11 OK
I/O SLOT 12 I/O 12 OK
If you see FAILED for any module, replace that module.
Starting a Session - Single MX-2100
When the terminal is used to control a single MX-2100, always assign node
address 0 to MX-2100. Use the following start-up sequence to connect to a
MX-2100 assigned node number 0.
1. If you use the AUTO (Autobaud) mode, press the ENTER key three times.
This allows MX-2100 to identify the terminal data rate.
Assuming that MX-2100 successfully identified the data rate of the
supervision terminal, you will be notified if MX-2100 failed the power-up
self-test:
If you see Kilomux-2100 SELFTEST FAILED, MX-2100 must first
be repaired before you can continue using it.
If MX-2100 successfully passed the power-up self-test, it displays the
following:
<BEL>Kilomux-2100 SUPERVISORY PORT ON LINE. TYPE 'H' FOR HELP
where <BEL> stands for the graphic symbol of the <BEL> code (ASCII 07).