H.
CONTENT 1. INTRODUCTION ........................................................................................................................................ 4 1.1. PREODUCT INTRODUCE ................................................................................................................... 4 1.2. PRODUCT FEATURE .......................................................................................................................... 4 1.2.1. SPECIFICATION .......................................
1. INTRODUCTION 1.1. PREODUCT INTRODUCE The series of DVR include 4 channels,8 channels and 16 channels ,this is 4CH digital video recording DVR, which have local recording, playback, support triple code remote network surveillance, data backup, parameter setting, motion detection, I/O alarm setting, PTZ and USB mouse, USB2.0 backup, IE browser and back up etc. 1.2. PRODUCT FEATURE H.264 compression Two USB interface, USB2.0 for data backup, USB2.0 for mouse operation. Support 1 pcs 3.
Mouse Remote control voltage input USB Mouse Support DC12V/5A 1.2.2. BASIC WORKING PARAMETER Item Parameter Description Voltage input 12V DC 12V Video impedance input 75Ω 75Ω Each channel. Video output 1Vp-p 1Vp-p CVBS signal RS485 Connect to PTZ, (Pelco-D,Pelco-P) SATA HDD One SATA HDD (up to 2T) 1.3.
2. DEVICE OPERATION In device operation, the enter key on remote control has the same function as left click of the mouse. 2.1. REMOTE KEY INSTRUCTION 2.1.1. REMOTE CONTROL The remote control is the secondary input device For navigating the system’s interface. To use the remote control: 1. STANDBY: Press to turn on/off standby mode. 2. LOGIN/LOCK: Remote control can control the device through the device number is landing, Locked shielded remote control equipment 3.
2. If press【LOGIN/LOCK】+【0】, then the remote controller can control device with any number. 3. The number of device should be smaller than 000255. 2.1.3. MOUSE OPERATION The mouse is the primary input device for navigating system menus. NOTE: Unless otherwise noted, all system functions described in this manual are achieved through mouse input. To use a mouse with the system: 1) Connect a USB mouse to the USB MOUSE port on rear panel of the system.
5. Click 2.1.4. to enter/confirm and close the Virtual Keyboard. MENU TREE You can control the DVR by a lot of menu operation. This tree will show you the menu structure and it will be in details in after chapter.
2.2. SYSTEM OPERSTION 2.2.1. USER LOGIN 2.2.1.1 STARTING THE SYSTEM To power the system ON/OFF: Connect the power cable to the DC 12V port on the rear panel. At startup, the system performs a basic system check and runs an initial loading sequence. After a few moments, the system loads a live display view. ATTENTION: By default, passwords are disabled on the system. You do not need to enter a password when accessing any system menus.
Remark: You must after pressing “APPLY” to make the setting for submenu valid. It will no use when exit directly. This DVR have a special feature is: when you move the mouse to everywhere, there will have the explanation information showed auto. 2.2.2.1 DISPLAY Move the cursor to【DISPLAY】（Icon with the orange box means that selected）, press【Enter】to enter into the setting interface. CH01~CH04: click to pop up pull-down box to switch to other channel to carry out setting.
Press【Enter】or【+】【-】key or directly drag the cursor to set colors, including chroma, brightness, contrast and saturation, press【APPLY】to save the parameters.
LIVE TIME(display time while in live view)): ON: Means yes, OFF means not. RECORD TIME(display time while recording): ON: Means yes, OFF means not. 2.2.2.2 RECORD SETUP Move the cursor to 【RECORD】（Icon with the orange box means that selected）,press【Enter】to enter into the setting interface. Press【Confirm】 and enter into the setup interface, and you can use direction keys and cursor to change the options. CH01~CH04: click to pop up pull-down box to switch to other channel to carry out setting.
PACK TIME: There are 15min, 30min, 45min, 60min four options, that means it will pack as the mode you selected Scroll to APPLY and press ENTER to save the new settings. 2.2.2.3 NETWORK SETUP Move the cursor to 【NETWORK】 (Icon with the orange box means that selected), and press 【Enter】 to enter into setting interface . TYPE: There are DHCP & Static three options. ● STATIC Select [Static] in the type, and press [Enter] to enter into the interface as followings PORT： ： For video transmission via IE/CLIENT.
PORT: the communicate port between PC and DVR, recommend use default port. WEB PORT: setup the port of IE browser via HTTP. Remark: when you setup the net mode as DHCP, the router will arrange a dynamic IP for DVR. UPNP: Universal Plug And Play, the router will auto forward the DVR port MEDIA PORT: the communicate port between PC and DVR, recommend use default port WEB PORT: setup the port of IE browser via HTTP.
If succeed, the IP address will be automatically config as dynamic IP of WAN. DDNS: There are [ON/OFF], and if there is a DDNS service, please setup it as ON. Server: User can select required DDNS server, there are 4 options: 3322, dyndns,nightowldvr,no-ip. Domain NAME: Input the name of the host server. USERNAME: Input in the name of the user. PASSWORD: Input the password for DDNS. 2.2.2.
via click the corresponding period. PLAY: You can press 【Enter】 input number directly to setup playback time. After setting, move the cursor to “PLAYBACK”, and then press”APLLY”to enter into video playback of that time. Also you can select any period of time in the video status frame after searching,press”APLLY”to enter into the video playback of this period. DETAIL FILES: Enter into the video file list interface of the selected date. LOG SEARCH: Enter into the log searching interface. 2.2.2.
can press【 】to pause and frame by frame play; Press【Exit】to exit from playback and return to the former menu; 5. When finished playback files, it will return to the file list interface. 2.2.2.6 BACKUP You can use USB for backup, should insert USB device into the USB2.0 port before backup files. And it is support USB OTG.
2.2.3. DEVICE SETUP Move the cursor to【DEVICE】（Icon with the orange box means that selected）,press【Enter】to enter into setting interface. Advanced Features include HDD, ALARM, PTZ, MOBILE and MOTION DETECT. 2.2.3.1 HDD MANAGE Move the cursor to 【HDD】（Icon with the orange box means that selected）,press【Enter】to enter into the setting interface, and you can use direction keys and cursor to change the options. HDD STATUS: There status is ok means the HDD is ok.
CH01~CH04: click to pop up pull-down box to switch to other channel to carry out setting. I/O ALARM: Each channel has an I/O status, that is, when an alarm triggered, it will activate the corresponding channel to start alarm recording. N.O: indicate I / O input level from high to low effective N.
PTZ Control 1. 2 3 All Functions Pointer Auto Pan To select the direction of PTZ The middle circle is for auto pan of PTZ.
Zoom in/zoom out Focus Iris Volume PTZ control the speed Channel select For selecting the channels of PTZ camera. Cruiseset To cruise setup Exit To back to previous page or exit Go to preset point Allow you to go to a specific preset point. Set Ponit Allow you set a set of specific preset points of a PTZ camera. Also it can Adjust the camera in a fix point. Clear Allow you to delete the selected preset Curoint It indicates the starting point cruised. System default point is 01.
into setting interface. PORT: the port for mobile view, you should open the port in the router for mobile view. Please note that the server port of DVR must with the same port of mobile . Network: Select different mobile network from the options of WIFI, 2.5G, 2.7G,3G and WIFI, and press [Enter] to switch different network. 2.2.3.5 MOTION DETECT Move the cursor to【MOTION】（Icon with the orange box means that selected）,press【Enter】to enter into setting interface.
Move the direction key on remote control to make cursor move in the small pane, green frame means the cursor has moved to this pane, press【Enter】to select or cancel motion detection of this small pane, when setup finished, press【exit】to back to MD setup interface, it will save automatically. Remark: IR Operation: press [Menu] key to select or cancel the entire screen. Mouse operation: click left and drag the frame to setup the region for motion detection. 2.2.3.
DATE: Setup system date via numeric key. DATE FORMAT: Press ENTER to switch between the date patterns, there are YY-MM-DD and MM/DD/YY two options. TIME: Setup system time via numeric key. TIME FORMAT: Press ENTER to switch between the date patterns, there are 12 HOURS and 24 HOURS two options. Remark: You must press 【APPLY】 to save it, otherwise it won’t save the modify if you exit this interface. DST: DST settings, you can setup DST as you want here. 2.2.4.
default password is: 123456), default password of [user1] is: 123456) User Right：[Control PTZ]: Have right to control PTZ [Config. Argum.]: Have right to change system parameters settings. [System Maintain]: Have right to maintain systems(Such as system upgrade, system default ) control channel: control channel whether to display the image preview of IE browser，When checked, the channel image，Does not display when not checked 2.2.4.
System language have Chinese ,English ,Russian ,Portuguese ,Spanish ,Turkish ,Italian ,Persian ,French and Polish ten options, you can setup the language you want in here.（Different versions of the language there will be differences） Remark: The device will restart when you setup system language success. 2.2.4.
AUTO MAINTAIN: When switch is on, you can setup the time for device to restart. SYSTEM UPDATE: Copy the update file to the “dvrupgrade” folder in the root directory of the thumb driver, and insert it into USB 2.0, then press [Enter] to upgrade the firmware, and it will display the process of the system upgrading, as following. REBOOT: means restart the device. POWER OFF: The button allows to shut down the system from OSD.
3. IE OPERATION 3.1. CONNECTION SETTINGS DVR through the remote access network, local area network connection, the client computer's IP address must be with the DVR at the same network segment, in the wide area network connection through the dynamic IP address or domain name to connect, when the two sides need to ensure that public network can access it. The following introduces the method of local area network connection settings: 1.
Figure 3-4 4. Double-click "Internet Protocol (TCP / IP)".
Figure3-5 5. See PC's IP address, subnet mask, default gateway. (Figure 8-5 in the parameters depending on the specific circumstances of different users) 6. DVR set up the corresponding IP address, subnet mask, and default gateway (see section 6.5 Network Settings). DVR which the subnet mask, default gateway and the PC the same as, IP address must be in the same network segment, but you can not have been used with the same IP address, or IP addresses will result in conflict.
Remark: If you connect the device in WAN, the IP should be a public IP. 3.4. OPERATION INTERFACE There are Live view, Playback and Setup options in the main interface, please press them to access it. 3.4.1. LIVE Click to enter into the interface as followings 3.4.1.1 PTZ CONTROL Change the focus, preset aperture to control the PTZ. Click to up/down/left/right control movement of the PTZ.
3.4.1.3 PTZ PRESET Setup preset point. You can control it via the below three buttons: 3.4.1.4 PLAY Move cursor to the icons, it will highlighted when selected Open all windows. Capture picture, save in local disk, the default save path is C:/DVR Quickly start all channels’ recording video, here the left up corner of each channel have normal recording video symbol 【R】, click icon to switch between single screen /16 split / full screen /quad /nine . Volume adjust button 3.4.1.5 OTHER OPERATION 1.
Step 4. Click specified video file which you would like to playback, remotely. The video will be displayed. When the video file is playing, the system won’t allow you to download video files. Step 5. Close the playing video and then click button to download video file. Step 6. When the video file was downloaded, the dialogue box will display.
Step 7. Playback control The above purple progress bar shows download progress, green progress bar shows playback progress Switch between pause/play Pause Stop play Fast play Slow play Pause at next frame 3.4.3. REMOTE SETTING Click to enter into setup interface, this interface include Encode setting, Record setting, Alarm setting, PTZ setting, Network setting,Advanced setting and system information seven menus. 3.4.3.1 ENCODE SETTING Click as in GUI of DVR.
Click in GUI of DVR. Click GUI of DVR.
when you see ” which you would like to copy. ” button, you can copy the setting to the channel 3.4.3.2 RECORD SETTING Click in GUI of DVR.
3.4.3.3 ALARM(Optional) Click and parameter settings as in GUI of DVR. Click of DVR.
3.4.3.4 PTZ Click DVR. to enter into setup interface; you can check the parameter settings as in GUI of 3.4.3.5 NETWORK Click GUI of DVR.
Click ，enter into [UPNP] settings interface as below: After open UPNP, DVR IP will be automatically maped to the router.(Note: It requires router supports this function and UPNP opened) 3.4.3.6 ADVANCED SETTING and Click the parameter settings as in GUI of DVR.
Click and the parameter settings as in GUI of DVR. Click as in GUI of DVR.
3.4.3.7 SYSTEM INFO to enter into system information interface (see below picture), this interface Click shows HDD status, remain record time, firmware version, and all the information is fixed.
3.4.3.8 USER SETTING Click to enter into system information interface，Only the administrator "admin" users can log in to add (to add up to four ordinary users), and only administrators can modify the normal user name and password corresponding to the ordinary user, each user name must be the corresponding password to log in and the corresponding operating authority, the default administrator user name: admin ，password is 123456 3.4.4.
FILE SAVE PATH: capture picture and recording video save path 3.4.5. LOGOUT Click Switch to login screen. 3.5. PRODUCT OVERVIEW 3.5.1. The Definition of Buttons and Connectors on DVR Front Panel Buttons on Front Panel NO.
Connectors on Rear Panel Item Physical connector Connector description 1 V-out One video output for connecting TV or monitor (BNC) 2 Video In For connecting analog video signal input (BNC) 3 VGA For connecting VGA monitor 4 Net For connecting Ethernet 5 A-out For connection audio output 6 USB/MOUSE USB2.0/USB mouse 7 Audio In Audio input 8 DC +12V Power interface 9 Power switch Power On/Off 10 RS485+ RS485- RS-485 for connecting PTZ 3.6.
Connection diagram of AC alarm input as following: The connection diagram of alarm output as following: 45
System Network Diagram 3.7.
Notice: Newly installed HDD should format before recording 47
4. FAQ If your problem is not listed below, please call our toll-free number for more support. 1. 2. 3. 4. 5. 6. 7.
8. Question: No audio sound when playing back? Answer: Setting problem: open audio-video item Check the audio to see if it is closed in playback interface 9. Question: System time is not correct? Answer: Wrong setting or user did not click "Edit" to confirm Battery is not connected properly Battery is dead. Please change. 10.
5. P2P DIT Platform 1. Check user name and password on the label at the bottom of the DVR 2. Login DVR via website: http://ie.scc21.com First download and install the Plug-in file .then input the DVR ID number and login password. 3.
Click WAN button and input DVR ID number、login password, then click login button 51
