OWNERS MANUAL MSS410 / MSS510 / MSS610 Loudspeaker Systems MSS410 MSS510 MSS610 McIntosh Laboratory, Inc.
Thank You, Please Take A Moment, Customer Service and Table of Contents Thank You Table of Contents Your decision to own this McIntosh MSS410, MSS510 or MSS610 Series Loudspeaker System ranks you at the very top among discriminating music listeners. You now have The Best. The McIntosh dedication to Quality, is assurance that you will receive many years of musical enjoyment from this unit. Please take a short time to read the information in this manual.
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. General: 1. Read all the safety and operating instructions, contained in this owners manual, before operating this equipment. 2. Retain this owners manual for future reference about safety and operating instructions. 3. Adhere to all warnings and operating instructions. 4. Follow all operating and use instructions. 5.
Introduction, Performance Features and Overall Dimensions Introduction The McIntosh woofer/midrange drivers offer extremely smooth frequency response, low distortion, high sensitivity and high power handling capability. When these drivers are combined with other McIntosh Automotive components, you will enjoy sonically accurate music reproduction in your vehicle which meets McIntosh traditional standards of excellence.
Overall Dimensions cont Top View of the MN410, MN510 and MN610 Side View of the MN410, MN510 and MN610 Front View of the MS640 Front View of the MS540 Side View of the MS540 Side View of the MS640 5
Installation Installation It is recommended that a qualified professional install all McIntosh Automotive Products. McIntosh Woofer/Midrange Drivers, Tweeters and Crossover Networks should be used in conjunction with McIntosh Subwoofers and McIntosh Automotive electronics to achieve the best possible performance.
Installation, cont Dual Angle Mounting Bracket inside view Mounting the Tweeter Dual Angle Bracket Two different tweeter mounting angles are possible with the bracket supplied. Choose the one which best fits the vehicle. Refer to Figures 4 and 6. 1. Drill holes with an appropriate size drill bit in the mounting surface for the two tweeter wires and the two bracket mounting screws. Also drill corresponding holes in the mounting surface. 2. Secure the bracket with two of the screws supplied. 3.
How to Connect a Two Way System How to Connect a Two Way System 1. Press the connector ends of the supplied Woofer/ Midrange Red/Black cables onto the matching Woofer/ Midrange connecting lugs. Connect the Tweeters in a similar manner. 2. Attach the tinned ends of the two Red/Black Woofer/ Midrange cables to the Crossover Network WOOFER OUTPUT terminals. The Black wire connects to a MINUS (-) terminal and the Red wire to a PLUS (+) terminal. 3.
How to Connect a Bi-AmpThree Way System How to Connect a Bi-Amp Three Way System Configure the Crossover Networks for BiAmp operation by performing the following modification. When facing the terminal side of the Crossover Network, cut the two wire loops located on the left side. Refer to Figure 9. 1. Press the connector ends of the supplied Woofer/ Midrange Red/Black cables on to the matching Woofer/Midrange connecting lugs. Connect the Tweeters in a similar manner. 2.
Specifications MS440 MS540 MS640 Basic Parameters Peak Power Continuous Power (EIA + H.P.) Frequency Response Reference Sensitivity (SPLo) System Sensitivity1 Nominal Impedance (Znom) Free Air Resonance (Fo) Total Q (Qts) Equivalent Acoustic Volume (Vas) 120 Watts 60 Watts 80 Hz - 8kHz 88 dB 84 dB 4 Ohms 85 Hz 0.35 2.5 Litr 120 Watts 60 Watts 80 Hz -8 kHz 89 dB 85 dB 4 Ohms 53 Hz 0.38 13.4 Litr 120 Watts 60 Watts 80 Hz - 8kHz 89 dB 85 dB 4 Ohms 47 Hz 0.46 23.
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Laboratory. Please see the Part List for the correct part numbers.
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No.
