AM/FM Tuner Module TM1 Dealer Installation Guide McIntosh Laboratory, Inc.
Overview Table of Contents The McIntosh TM1 AM/FM Tuner Module adds AM/FM Broadcast Reception to the MX119, MX134 or MX135 A/V Control Centers; the MHT Series A/V System Controllers, C45 Audio Control Center and other McIntosh Components. It also adds functionality of a second Tuner to the MR85 AM/FM Tuner. Follow the instructions in this guide for installing the TM1 into the MX119, MX134, MX135, MHT Series, C45, MR85 and other McIntosh Components. The TM1 Tuner Module is not a user installable product.
Parts List and Connector Information Parts List Part Number 049084 034134 049192 049443 171404 171405 171406 Connector Information Description Figure Number AM/FM Tuner Module 1 Anti-Static Bag 1 RAA1 Remote AM Antenna 2 RAA1 Connection Cable Complete 2 Seven conductor ribbon cable 1 Six conductor ribbon cable 1 Four conductor ribbon cable 1 TM1 Serial Number Label 1 AM/FM Tuner Module Tuner Module Connecting Cables TM1 Serial Number Label Anti-Static Bag RAA1 Connectors Connect the shield and two lead
MX119, MX134 or MX135 Removing Covers 1. Remove ALL connecting cables from the Rear Panel of the MX119, MX134 or MX135 Cover Screws A/V Controller. 2. Remove two screws from each side and two screws from the back that secure the Top Cover to the MX119, MX134 or MX135. 3. Lift off the Top Cover by grasping the rear sides of the top cover and lifting up and away from the MX119, MX134 or MX135. 4.
MX119, MX134 or MX135 Installation Instructions closest to the MX119, MX134 or MX135 Rear Panel. Refer to figure 7. Note: The six pin Cable Plug and PC Board Socket are “keyed” to attach only in one direction, do not force it on backward. Figure 9 13.
MHT Series Component Removing Covers 1. Remove ALL connecting cables from the Rear Panel of the MHT Series A/V System Controller. 2. Remove two screws from each Cover side and two screws from the back Screws that secure the Top Cover to the MHT Series Component. 3. Lift off the Top Cover by grasping the rear sides of the top cover and lifting up and away from the MHT Series Component. 4.
MHT Series Component Installation Instructions Audio PC Board) to the four pin PC Board Socket (J5) of the Module, J4 which is the middle J5 one of the three inline connectors. J3 14.
C45 Removing Covers 1. Remove ALL connecting cables from the Rear Panel of the C45 Audio Control Center. 2. Remove two screws from each side and two screws from the back that secure the Top Cover to the C45. 3. Lift off the Top Cover by grasping the rear sides of the top cover and lifting up and away from the C45. 4. Remove the Inside Connector Cover which is secured with two Phillips Head Screws and is located on the Rear Panel. Refer to figures 18, 19 and 20.
C45 Installation Instructions four pin Socket of the Module, which is the middle one of the three in-line connectors. 14. Also attach the remaining plug of the Seven Conductor Ribbon Cable coming from the seven pin Socket “J21” (as indicated on the C45 Data PC Board) to the seven pin Socket of the Module, which is located closest to the C45 Front Panel. Note: Refer to the C45 Owner’s Manual for additional Operational Details.
MR85 Removing Covers 1. Remove ALL connecting cables from the Rear Panel of the MR85 AM/FM Tuner. Cover Screws 2. Remove two screws from each side and two screws from the back that secure the Top Cover to the MR85. 3. Lift off the Top Cover by grasping the rear sides of the top cover and lifting up and away from the MR85. 4. Remove the Inside Connector Cover which is secured with two Phillips Head Screws and is located on the Rear Panel. Refer to figures 27 and Figure 27 28.
MR85 Installation Instructions 13. In a similar fashion, attach the J3 plug of the Four AM/FM J5 Conductor Ribbon Tuner Cable coming Module J4 from the six pin PC Board Socket Cables from Main Audio “J2” (as indicated PC Board on the MR85 Main PC Board) to the four pin Socket “J5” of the Module, which is the middle one of the three in-line connectors. 14.
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No.
