Instruction Manual

Specification WBL-0410 WBL-0420 WBL-0430
Optical parameter
Luminous area (A x B) 45mm x 100mm 45mm x 200mm 45mm x 300mm
Light emission rectangular light field with direct fired LED
Recommended use commonly used as incident light for larger objects with various mounting positions, e.g. for print inspection
Luminous Flux of white LEDs [lumen]
1)
1380lm 2760lm 4140lm
Radiant Power of red LEDs [mW]
1)
4060mW 8120mW 12180mW
Radiant Power of IR LEDs [mW]
1)
1950mW 3910mW 5860mW
Electrical parameter
Available interfaces -s with integrated LED Controller and 4 operation modes; -x with direct LED accress (external LED control is required)
Uin for -s Version 24V DC +/- 5%
ULed(+) range for -x version
2)
WT / BE / YE: 17 … 20 VDC; GN: 20 ... 23 VDC; RD: 12 … 15 VDC; IR: 9 … 12 VDC
Typical Power (-s version)
Steady light operation 8W 16W 24W
During ON time at flashed light operation 18W 44W 56W
Recommended LED current (-x version)
Steady light (100% duty cycle) 450mA 900mA 1350mA
Flash light (50% duty cycle, 500ms pulse) 900mA 1800mA 2700mA
Flash light (25% duty cycle, 50ms pulse) 1350mA 2700mA 4050mA
General parameter
Dimension (H x W x D) 54mm 110mm x 23mm 54mm x 210mm x 23mm 54mm x 310mm x 23mm
Weight 200g 380g 560g
Material Black anodized aluminum housing with PMMA light cover
Connector M8x1 socket, 4 pin, male (pinning details on the next page)
Operating temperature 10°C to 30°C
Certifications CE, RoHS
Degree of protection IP54
Humidity 30% to 70%
Accessories For cable, foil holder brackets, light manipulation foils and external LED controller: please check www.mbj-imaging.com
1) Values are approximate with a +/- 7% tolerance
2) Lower voltage value refers to steady light, higher voltage value refers to flash light, please see max. allowed current in the row below
Electrical Connection
The lighting is equipped with an 4 pin M8x1 connector.
Pin Color
1)
Standard (-s) Direct (-x)
2)
1 brown 24 VDC LED (+)
2 white Dim LED (+)
3 blue Trigger LED (-)
4 black Ground LED (-)
1) Wire color of MBJ lighting cable
2) Connection to 24VDC without external LED controller may destroy the unit
Additional Information:
Pin3 (Trigger) is an ‘active high’ input signal with 5…24V=ON and 0...1V=OFF,
it is a high resistance current sink with 0.2mA for 5V and 5mA for 24V
Pin2 (DIM) is used as brightness control and operation mode switch, it is a
high resistance current sink with 0.2mA for 5V and 1mA for 24V.
For the connection it is recommended to use the MBJ lighting cable with a
maximum length of 10m.
Integrated Controller (-s)
Supported operation modes with the integrated LED controller
Pin 2 (Dim) Operation mode
24V steady light
1)
1...10V steady light with brightness control
2)
24V triggered light
GND triggered flash light with max. 20ms and
up-to 100% more light intensity
3)
1) Pin 3 (Trigger) needs permanent 24V to activate steady light mode
2) PWM with 3.8kHz clock is used, recommended minimal camera exposure is 5ms
3) Latency between trigger and LED light ON is about 20...30µs, the maximum recom-
mended clock speed is 1 kHz, the maximum recommended duty cycle is 25% and the
minimum recommended flash time is 100µs
Triggered light with NPN sinking output
(inverted strobe signal, open collector)
Flashed light with PNP sourcingSteady light Steady light with brightness control
Application Samples for (-s) controller
1 Power
2 Dim
3 Trigger
4 GND
24V DC
MBJ
LED light
MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
24V DC
24V DC
10k
10k
24V DC
2k2
10 mA
from Camera/ PLC etc
MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
2k2
MBJ
LED light
1 Power
2 Dim
3 Trigger
4 GND
24V DC
24V DC
10 mA
from Camera/ PLC etc