USER MANUAL Version 2.0 Please read manual before you operate the product!!! Disclaimer: Product specification, color and other features may slightly change to reflect the latest product update from manufacturer without prior notice to user. All rights reserved.
Important to know about the digital radio coverage Please note that digital radio is currently only available in Australian metropolitan cities. It is not available in remote area yet. You can visit www.digitalradioplus.com.au to discover the coverage of the available digital radio broadcasting around Australia by typing your living area postcode. Please make sure that your area has digital radio signal available to use the DAB+ mode.
• A wider choice of shows and program highlights better meets the needs of niche audiences With digital radio all you need is a digital receiver or a device with a DAB+ chip in it and that’s it – no subscription fees, no messing about with signing up or logging on, just tune in.
1 2 3 4 5 6 7 8 9 Speaker LCD Display ON/ OFF Key Display Key Scan Key Preset Key Menu Key Volume Down Key Volume Up Key 10. DAB+/ FM Mode Key 11.Previous Key 12. Select Key 13. Next Key 14. 3.5mm Earphone Socket 15. DC Power Socket 16. Aerial Input 1. DAB+ radio functions 1.1 How to power the device 1.1.1 Main Adaptor (supplied with the package). Connect the mains adaptor to the DC power socket of the radio to the wall socket. 1.1.2 Battery (not supplied).
The radio will auto enter” SYNC TIME” to sync the CLOCK time with DAB+ radio station and then enter into Standby mode. If it is the first time to use the digital radio, after “SYNC TIME”, press the power button to activate the radio tuning function if it enters standby mode without doing anything. The LED backlit will turn off and enter power save mode after a while. Press any key to turn on the backlit. 1.1.5 Radio LED display panel information 1.1.
1.2 How to adjust the volume Press the "Vol+" up to increase the volume and the "Vol-" down to decrease the volume. Press and hold the "Vol+” or "Vol-" to progressively increase or decrease the volume. 1.3 How to change the radio stations 1.3.1 If you are not already in DAB+ mode, Press the "DAB+/FM" button to go to DAB+ mode. Then you can press "DAB+/FM" button again to go to FM mode. 1.3.2 Press the "◄◄" or "►►" button, to scroll through the stations.
during the scan will be displayed .A local scan takes approximately 20-30 seconds to finish. 1.4.3 If you are using your DAB+ radio outside of the UK, then Press and hold the "Scan" button for 2 seconds to begin a wider, national and full scan. A national and full scan takes approximately 30 seconds but can take up to 3 minutes depending on the area and signal strength. 1.
1.5.3 Using the "◄◄" or "►►" button, select the preset number that you would like to store the station to Press the " station. " button to store the For example: I am listening “3AW” in DAB+ mode, I want to preset it into my favorite stations. First to press and hold “Preset” button for seconds, the LCD shows message like ”EMPTY P1”, then I press “Select” key , so the LCD shows “3AW P 1” , if I want to store this station in 2-10 , I can press the "►►" button to choose from 1-10 as I like.
CHANNEL FREQUENCY: Display channel frequency STATION LOCALITY: Display DAB+ radio broadcast place VERSION: Display DAB+ radio station version information 2. Using the menu key under DAB+ mode The "MENU" button enables you to change some of the default settings of your Radio, so that it works just the way you want it to. Use " " to confirm your choose, use "◄◄"or "►►" to scroll through the menu list. 2.1 For DAB+ mode, the main menus are as below 2.1.
Display sync time of the DAB radio station. Under CLOCK information, press” t” and use "◄◄"or "►►" to scroll between AUTO COLOCK or MANU CLOCK to adjust CLOCK time 2.1.5 12/24 H Choose to display time under 12/24 hours mode. 3. System reset Press and hold the “DAB+/FM” button for 3 seconds. The LED display will show” RESET”. Press “ ” button to confirm after that the radio is back to original factory settings and all previous settings in the radio are eliminate.
4.4 Signal Not Available When there is no signal received after the FULLSCAN has been done, the display will show “OFF AIR”. It may due to weak station signal. Please check if Antenna has been pulled out and try to do the scan again. 5. Product Q&A If you are experiencing problems with your DAB+ radio there are some quick and easy checks that you can do, which may help to solve the problem.
6. Warranty registration To receive the full support of your product, please register your product and your details with our distributor in your country, for Australian user, go to www.ultra-imagiantion.com , click product registration page to fill out the details. Join us at facebook™, by searching “ultraimaginationtechnology” for our distributor information or “mbeat” for mbeat® information. Keep updating with product information and you have the chance to win the monthly prize or free gift from us.
