RVM2.
PRE-INSTALLATION CHECKLIST Thank you for purchasing the MB Quart RVM2.0 multi-zone mini RV radio with AM/FM and Bluetooth audio streaming. Please take a few minutes to review the user manual before attempting installation and operation. Additional support documentation can be found at MBQUART.com or by emailing support@maxxsonics.com.
WIRING & INSTALLATION REAR PANEL DETAIL WIRING DIAGRAM 3
WIRING & INSTALLATION INSTALL THE UNIT Please note: This unit requires a minimum 3” mounting depth which includes space for the electrical/speaker plugs and any A/V input and output connections. 1. Cut or utilize a mounting opening 3-7/8”(H) x 4”(W). 2. Remove the left and right decorative covers as shown in the diagram. 3. Insert the unit into the mounting opening. 4. Attach the unit using the four (4) supplied mounting screws. 5. Replace decorative side covers over mounting screws.
FRONT PANEL CONTROLS & INPUTS 5
FRONT PANEL FUNCTIONS (BY MODE) BUTTON ACTION RADIO USB AUX IN BT MUSIC PWR/ Short Power ON / Dimmer Power ON / Dimmer Power ON / Dimmer Power ON / Dimmer Dimmer = H/M/L/OFF Dimmer = H/M/L/OFF Dimmer = H/M/L/OFF Dimmer = H/M/L/OFF Power OFF Power OFF Power OFF Power OFF Zone 1 Active or Zone 1 Active or Zone 1 Active or Zone 1 Active or Disabled Disabled Disabled Disabled Zone 1 Mute ON/OFF Zone 1 Mute ON/OFF Zone 1 Mute ON/OFF Zone 1 Mute ON/OFF Zone 2 Active or Zone 2 Acti
OPERATION POWER AND BASIC ADJUSTMENTS Turn the Unit ON or OFF Press button to turn the unit ON. When the unit is switched on, press and hold button for 2 seconds to switch the unit OFF. A “GOOD BYE” message is displayed to confirm power down.
OPERATION POWER AND BASIC ADJUSTMENTS (Continued) Alarm Operation The alarm built into the unit functions as a wake-up alarm. It could also be used to automatically turn the unit on at a specific time (such as a meal or evening time to relax). In setting menu turn ALARM to “ON” and set the wake-up alarm time (see below Alarm Time Setting). When the wake-up alarm time is set, the unit will generate a wake-up beeping sound at the preset time. The beep sound stops when any key pressed.
OPERATION ZONES, DISPLAY & AUX INPUTS ZONE 1 Operation ZONE 1 is connected to the unit’s on-board FRONT speaker and preamp-level RCA outputs. Quickly press and release the ZONE 1 button to select between the zone being active or disabled. The LCD screen will indicate the status of the zone above the button. Rotate the VOLUME/SEL knob up or down to adjust the ZONE 1 volume when it is in the active state. When ZONE 1 is in the disabled state, the VOLUME/SEL knob only controls the active zone.
OPERATION AM/FM RADIO Receive a Radio Station There are 3 FM station groups - FM1, FM2 and FM3. There are 2 AM station groups - AM1 and AM2. To select a radio station group, press the MODE button to select the radio mode. Next press BAND button to select desired group (FM1, FM2, FM3, AM1 or AM2). Press and quickly release the / button to tune by automatically seeking up or down to the next available radio station frequency.
OPERATION USB Sources When an USB source such as a thumb drive or portable media player is inserted to the USB port on the front panel of the unit, it supports playback of MP3 and WMA files automatically. To select USB as the source, press the MODE button until the USB mode display appears. Selecting Music Files Selecting the files uses the icon-based buttons below the LCD to the right. Refer to page 5 for the icon button locations.
OPERATION USB Sources (Continued) Directory+/- Function If you have a USB device set up with folders (such as by artist or playlist), the Directory function allows you to navigate the folders for MP3 and WMA music files. Press DIR+/ DIR- button to select next/previous folder to play. Once in the directory function, use the +10/-10 to navigate the folders. Press and hold DIR+/ DIR- button for 2 seconds it will skip +10/-10 file to play.
OPERATION BLUETOOTH SOURCES Bluetooth Pairing You must first pair a Bluetooth-enabled device to stream music to your unit. Select “search” or “discover” on the Bluetooth device while the unit is in the BT MUSIC mode. “RVM2.0” should appear in the list of available devices. Select “RVM2.0.” If a password is required, input “0000.” When successfully paired, BT MUSIC is displayed on LCD. If no Bluetooth device is paired, “UNPAIRED” will show in the LCD display.
SPECIFICATIONS GENERAL Power Supply Requirements: Current Drain: Maximum Output Power: Preamp Output Voltage: DC 12 Volts, Negative Ground 10 Ampere (max.) 4 x 17 watts into 4 Ohms @ 14.4V DC 2.1V (with AUX, USB or AM/FM Source) 1.5V (with BT Source) Chassis Dimensions : 3-7/8”(H) x 4”(W) x 2”(D)* *Note: Installation depth requires 3” minimum Tone Controls: Bass (at 100 Hz): Treble (at 10 kHz): RADIO ±10 dB ±10 dB FM Frequency Coverage IF Sensitivity FM Stereo Separation AM 87.5 to 108 MHz 10.
SPECIFICATIONS FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
