Programming instructions

RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for MazdaVehicles
Pacic Accessory Corporation
®
| Santa Ana, California 92705 | Ph. 866-931-8021 | [e-mail]
©2012 Pacic Accessory Corporation
www.pac-audio.com
Rev. 052413
Pacific Accessory Corporation
Page 3
Radio Alpine JVC Kenwood Clarion
S
ony
/O
ther
*
Pionee
r
Fusion
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Preset - Preset - Track +
6 Source Track - Track + Search - Source Source Track -
7 Track + Band/Disc + Track - Band Track + Track + Audio
8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Power
9 Power Select Disc/AM - Send Band Band
10 Enter/Play Attenuation Answer End Phone Menu
11 Band/Program Phone Receive Voice Dial Answer Call
12 Receive Phone Reject On Hook End Call
13 End Voice Dial Off Hook Voice Activation
14 Power
Mute (only
supported on
Multimedia units)
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart below. If you
come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the
program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have successfully
skipped that function and are ready to proceed to the next one.
Optional Programming Order
Alpine JVC Kenwood Clarion Sony/Pionee
r
Fusion
V
olume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume -
Mode Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Track +
Track - Track - Track - Track - Search - Track - Track -
V
oice/Mute Mute Mute Mute Mute Mute Mute
Answe
r
Receive Receive Answer Send Answer Audio
End End Selec
t
Pla
y
End Phone Menu Powe
r
Default SWC Button Assignments
Optional Steering Wheel Control Programming
Default Steering Wheel Control Programming (cont.)
1. Turn the key to the ignition position.
2. Press and release programming button on the side of the interface.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.
At this point you have two options:
A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.
B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will
go back to solid.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
6. Once programming is completed, wait seven seconds. The LED will ash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps
1
2
3
4
5
6
7
8
9
0
Alpine Clarion Fusion JVC Kenwood Pioneer/Sony/Other
1 4 9 2 3 7
Other = Advent, BOYO, Dual, Lightning Audio, Visteon,
SET RADIO SELECT SWITCH