Table of Contents Table of Contents Introduction Instrument Cluster 3 10 Warning and control lights Gauges 10 15 Entertainment Systems 17 AM/FM stereo with CD AM/FM stereo with cassette and in-dash six CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control 17 27 44 44 48 48 50 51 56 56 58 61 62 63 Locks and Security 70 Keys Lock
Table of Contents Brakes Transmission operation Vehicle loading Trailer towing Recreational towing 125 129 148 151 156 Roadside Emergencies 157 Hazard flasher switch Fuses and relays Overheating Jump starting Wrecker towing 157 158 164 171 177 Customer Assistance 179 Reporting safety defects (U.S.
Introduction Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed.
Introduction SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially including but not limited to information such as: • the use of restraint systems including seat belts by the driver and passengers, • information about the performance of various systems and modules in the vehicle, and • information related to engine, throttle, steering, brake or other system status potentially including information related to how the driver operates the vehicle in
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Window Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine Air Filter Traction Control Passenger Compartment Air Filter Jack Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time
Instrument Cluster Instrument Cluster Headlamp and turn signal control (pg. 48) Fog lamp control* (pg. 48) Power mirror control* (pg. 62) Windshield wiper/washer control (pg. 56) Instrument cluster (pg. 10) Speed controls* (pg. 63) Instrument panel Driver air bag dimmer/dome light (pg. 100) control (pg. 49) Hood release handle (pg. 203) * if equipped 8 Manual tilt steering column lever (pg.
Instrument Cluster Rear window defroster control (pg. 47) Hazard flasher control (pg. 157) Audio system (pg. 17) 4WD control* (pg. 138) Cigarette lighter Climate controls (pg. 44) Auxiliary power point (pg.
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL CAP Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off.
Instrument Cluster It may take a long period of time for the system to detect an improperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and specifications chapter.
Instrument Cluster Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by an authorized Mazda dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly.
Instrument Cluster Four wheel drive indicator (if equipped): Illuminates when four-wheel drive is engaged, refer to the Driving chapter. Note: If the light continues to flash, have the system serviced by an authorized Mazda dealer. Anti-theft system: Flashes when the Securilocky Passive Anti-theft System has been activated. Refer to SecuriLocky passive anti-theft system in the Locks and Security chapter. Speed control: Illuminates when CRUISE the speed control is activated.
Instrument Cluster GAUGES CHECK FUEL CAP Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Refer to Engine coolant in the Maintenance and Specifications chapter.
Instrument Cluster Odometer: Registers the total kilometers (miles) of the vehicle. Trip odometer: Registers the kilometers (miles) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems Entertainment Systems AM/FM RADIO WITH COMPACT DISC PLAYER Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running.
Entertainment Systems AM/FM select Ensure that the ignition is in the ACC or ON position for the radio to operate. Press the AM or FM1/2 control to enter radio mode. Band selection Select AM by pressing the AM button and FM1 or FM2 by pressing the FM1/2 button. The selected mode will be indicated. If FM stereo is being received, ST will be displayed. Note: If the FM broadcast signal becomes weak, reception automatically changes from STEREO to MONO for reduced noise and the ST indicator will go out.
Entertainment Systems Turn the TUNE control to the left for a lower frequency. Turn the TUNE control to the right for a higher frequency. Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disable scan mode. Scan function in CD mode Press the SCAN control during CD play to hear the first ten seconds of each track.
Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the audio control until TREB is displayed. Turn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the audio control until BASS appears. Turn the control to increase (right) or decrease (left) the amount of bass output.
Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers.
Entertainment Systems Press the audio control until MID appears in the display. Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display. Release the TUNE control when the desired level is reached. NOTE: Approximately 5 seconds after selecting any mode, the volume function will be automatically selected. To reset the mid-range, press the TUNE control for approximately 2 seconds.
Entertainment Systems Starting autoset memory preset 1. Press the AM or FM1/2 control to select a frequency. 2. Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. 3. When the first six strong stations are filled, the strongest station will start playing. 4. Press the AUTO-M (Auto memory) control to select from the stored stations. One stored station will be selected and played each time the control is pressed. The frequency and channel number will be displayed.
Entertainment Systems Press the VOL (Volume) control to stop cassette play. CD select To begin CD play: 1. Insert a CD into the slot, label side up. The system will auto-load the CD and begin play after a short pause. The disc number and the track number will illuminate in the display. Rewind The rewind control works in CD mode. In CD mode, press and hold the rewind control to reverse through a track at a high speed.
Entertainment Systems Track search Track search works in CD mode. on the TRACK control Press the to skip forward to the beginning of the next track. on the TRACK control Press the to skip back to the beginning of the current track. Disc search Disc search works in CD mode. Press the DISC up control to skip forward to the beginning of the next CD. Press the DISC down control to skip back to the beginning of the previous CD. Ejecting a CD The eject feature works in CD mode. 1.
Entertainment Systems Random play in CD mode Press the RDM control during play. RDM will illuminate in the display. The next selection will be randomly selected. To disengage random play, press the RDM control again. Setting the clock The clock can be set at any time when the ignition switch is in the ACC or ON position. 1. Press and hold the CLOCK control for approximately 2 seconds until a beep sound is heard. The clock’s current time will flash. 2. Press SCAN on the hour set control to adjust the hours.
Entertainment Systems Press the CLOCK control to alternate the display. NOTE: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode. AM/FM RADIO WITH CASSETTE TAPE AND COMPACT DISC PLAYER/CHANGER (IN-DASH CD CHANGER) Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off.
Entertainment Systems Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE: Once the system is turned off, press the VOL control again to listen to the frequency last tuned to. AM/FM select Ensure that the ignition is in the ACC or ON position for the radio to operate. Press the AM or FM1/2 control to enter radio mode.
Entertainment Systems Press the TUNE control to select the desired function. Turn the TUNE control to adjust the desired levels. Refer to Treble adjust for specific instructions on level adjustments. The TUNE control will also work in radio mode to manually increase or decrease the frequency. Turn the TUNE control to the left for a lower frequency. Turn the TUNE control to the right for a higher frequency. Scan function The scan function works in radio and CD mode.
Entertainment Systems Scan function in CD mode Press the SCAN control during CD play to hear the first ten seconds of each track. Press the SCAN control again to stop the scan mode. NOTE: If the unit is left in scan mode, normal play will resume where scan was selected. Seek function The seek function control works in radio mode. Seek function in radio mode Press and momentarily hold the SEEK control. • Press to find the next listenable station up the frequency band.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the audio control until BASS appears. Turn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers.
Entertainment Systems Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Your vehicle may be equipped with a mid-range adjust. The TUNE control allows you to adjust the mid-range levels. Press the audio control until MID appears in the display. Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM control. 2. Select a station. 3. Press and momentarily hold the desired preset control until a beep sound is heard. The preset control number will illuminate in the display.
Entertainment Systems NOTE: If the power supply is interrupted, (fuse blows or the battery is disconnected), the preset channels will be canceled. Tape select (if equipped) To begin tape play, insert a cassette tape into the cassette slot, with the open edge facing the right. Once inserted, the cassette tape will automatically begin play and TAPE will appear in the display. At the end of the cassette tape, the unit will automatically reverse the cassette tape play.
Entertainment Systems Tape direction select Press the PROG RDM control to play the alternate side of a tape. NOTE: When the end of the cassette is reached, the audio system will automatically reverse play. Repeat play The repeat play feature works in tape and CD modes and allows you to listen to a selection repeatedly. Repeat play in tape mode Press the RPT control during play. RPT will illuminate in the display. The current selection will be repeated. To disengage repeat play, press the RPT control again.
Entertainment Systems Track search Track search works in CD mode. on the TRACK control Press the to skip forward to the beginning of the next track. Press the on the TRACK control to skip back to the beginning of the current track. Disc search Disc search works in CD mode. Press the DISC up control to skip forward to the beginning of the next CD. Press the DISC down control to skip back to the beginning of the previous CD. DolbyT noise reduction Dolbyt noise reduction operates only in tape mode.
Entertainment Systems APC in tape mode Press the APC control to advance to the beginning of the next selection. Press the APC control to reverse to the beginning of the current selection. To disengage APC, press the APC control again. If APC detects 15 seconds of blank space, it will automatically advance the tape to the next selection. NOTE: APC may not operate properly if: • A tape was recorded at a low level. • A tape has long, silent intervals. • A tape is a live recording.
Entertainment Systems Inserting CDs into desired tray number 1. Press and hold the LOAD control until a beep sound is heard. 2. Press the memory preset control for the desired CD tray within 5 seconds after the beep is heard. 3. When IN is displayed, insert the CD. NOTE: The CD cannot be inserted to the desired tray number if the number is already occupied. Eject feature The eject feature works in both tape and CD mode. Ejecting a tape Press the control to stop and eject a tape.
Entertainment Systems Multiple ejection 1. Press and hold the CD eject control for approximately 2 seconds until a beep sound is heard. 2. Wait approximately 5 seconds or press the CD eject control again within 5 seconds after the beep is heard. 3. Remove the CD. The next CD will then be ejected. NOTE: • CDs will be ejected in numerical order, lowest number first. • All CDs in the tray will be ejected continuously. • CDs can be ejected when the ignition switch is OFF.
Entertainment Systems 2. Press SCAN on the hour set control to adjust the hours. 3. Press AUTO-M on the minute set control to adjust the minutes. 4. Press the CLOCK control again to start the clock. NOTE: If the power supply to the unit is interrupted (if the fuse blows or the vehicle’s battery is disconnected), the clock will need to be reset.
Entertainment Systems • The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players.
Entertainment Systems • The CD player has been designed to play CDs bearing the identification logo as shown. No other discs can be played. • Do not stick paper or tape on the CD. Avoid scratching the reverse side of the CD (the side without a label). • Dust, finger smudges, and dirt can decrease the amount of light reflected from the signal surface, thereby effecting sound quality. Gently wipe a soiled CD with a soft cloth from the center to the edge.
Entertainment Systems Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Climate Controls Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor will operate in all modes , , and .
Climate Controls • MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers.
Climate Controls Operating tips • In humid weather conditions, place the climate control system in Defrost mode before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Climate Controls 4. Direct the outer panel vents towards the side windows. 5. To increase airflow to the outer panel vents, close the central panel vents. WARNING: Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER CONTROL The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Lights Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. OFF BATTERY SAVER Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beam position.
Lights High beams After turning the headlamps on, push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. OFF Flash to pass Pull toward you slightly to activate and release to deactivate. OFF INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim.
Lights AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. OFF INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position.
Lights The map lamp controls (without moon roof) are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps. If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the controls on either side of each map lamp to activate the lamps. This map lamp will illuminate whenever any door is opened. If any door has been opened from the outside, the lamp will remain on for 25 seconds after the door is closed.
Lights Function Number of bulbs Trade number Park/turn lamps 2 3157 AK (amber) (front) Headlamps 2 9003 Rear stop/tail lamps 2 3157K Rear turn lamps 2 3156K Rear license plate 2 3156K/168 lamps Backup lamp 2 3156K Rear/turn/sidemarker 2 916NA (amber) Fog lamp (if 2 899 equipped) Cargo lamp 1 211-2 Interior overhead lamp 1 912 (906) Front door courtesy 1 168 lamp Map lamps 2 168 (T10) Ashtray lamp 1 161 All replacement bulbs are clear in color except where noted.
Lights 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the rubber boot from the lamp assembly by pulling on one of the tabs. 5. Squeeze the retainer spring together releasing it from bulb hooks and rotate it away from the bulb. 6. Without turning, carefully pull bulb out of headlamp assembly. WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Lights Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly by pulling it rearward. 4. Twist the bulb socket counterclockwise and remove from lamp assembly. 5. Pull the bulb straight out of the socket and push in the new bulb. 6.
Lights 5. Pull the bulb straight out of the socket and push in the new bulb. 6. To complete installation, follow the removal procedure in reverse order. Replacing fog lamp bulbs (if equipped) 1. Remove the bulb socket from the fog lamp by turning counterclockwise. 2. Disconnect the electrical connector from the fog lamp bulb. 3. Connect the electrical connector to the new fog lamp bulb. 4. Install the bulb socket in the fog lamp turning clockwise.
Driver Controls Driver Controls MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF. Mist function: To mist, push control up from the OFF position and release to get one wipe.
Driver Controls Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the INT position. For normal speed rear wiper operation, rotate control upward to ON. To activate the rear washer, rotate position and the control to the release. Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seem less effective.
Driver Controls Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. 3. Replace wiper blades every 6 months for optimum performance. MANUAL TILT STEERING COLUMN To adjust the steering wheel: 1.
Driver Controls Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the Velcro pad (2) from the storage compartment door (3). • Place Velcro (5) on aftermarket transmitter (6) opposite of actuator control (8).
Driver Controls Approximate Thickness of Transmitter (GDO) Cut to Bottom of inches mm Notch Less Than 1/4 6.35 No Cut 7/8 22.00 Notch 2 1.0 26.00 Notch 4 1–3/16 32.00 Notch 6 • Reinstall the rubber actuator (1) in the storage compartment (7) by twisting and pushing it back into the slot. • Install the transmitter (6) on to storage compartment door (3) aligning the actuator control (8) with the rubber plunger (1). Close the storage compartment door (3) to verify proper fit.
Driver Controls The auxiliary power point is located on the instrument panel below the radio. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. Do not use the power point for operating the cigarette lighter element. The Maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 Watts, a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should supply a maximum of 120 Watts.
Driver Controls One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop. Note: This feature will only operate the driver’s side window. Window lock The window lock feature disables all the power windows except the driver’s. To lock out all the window controls except for the driver’s window press the right side of the control.
Driver Controls To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.
Driver Controls WARNING: Using cruise control in the following conditions could cause you to lose control of the vehicle: • Heavy or unsteady traffic • Slippery or winding roads • Similar restrictions that require inconsistent speed Don’t use cruise control in these situations. Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. ON OFF 3.
Driver Controls Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 48 km/h (30 mph). RSM SET ACC CST Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control.
Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control. RSM SET ACC CST Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
Driver Controls MOON ROOF (IF EQUIPPED) To operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time. • To close, press and hold the front portion of the control. To operate the moon roof vent position: • To open, press and hold the front portion of the control. This will open the vent.
Driver Controls CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels. To operate the shade: 1. Grasp the pull tube at the rearward edge of the shade and pull rearward. 2. Secure both ends of the pull tube in the retention slots located on the rear trim panels.
Driver Controls WARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. LUGGAGE RACK The maximum load for the roof rack is 44 kg (100 lbs), evenly distributed on the crossbars.
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLocky Passive Anti-Theft System for more information. POWER DOOR LOCKS The power door lock control is located on the driver door panel. Pressing the will unlock all the doors. Pressing the will lock all the doors.
Locks and Security Childproof door locks • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Rotate lock control in the direction of arrow to engage the lock.
Locks and Security The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACC) position. If there is a problem with the remote entry system make sure to take ALL remote entry transmitters with you to the dealership, this will aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’s door.
Locks and Security Sounding a personal alarm Press to activate the alarm. The horn will sound for a maximum of 30 seconds and the parklamps will flash for a maximum of 3 minutes. Press again or turn the ignition to ON to deactivate, or wait for the alarm to timeout in 3 minutes. Note: The personal alarm will only operate when the ignition is in the OFF or ACC position. Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.
Locks and Security Note: This procedure must be completed within the specified times. If not completed within the specified time period, reprogramming procedures must be restarted from the beginning. To reprogram the remote entry transmitters: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Ensure the vehicle is electronically unlocked. Put the key in the ignition. Turn the key from the 1 (LOCK) position to 3 (ON). Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (ON).
Locks and Security NOTE: The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. NOTE: The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the OFF position. SECURILOCKY PASSIVE ANTI-THEFT SYSTEM SecuriLocky passive anti-theft system is an engine immobilization system.
Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 2 (ACC) position. The light in the instrument cluster will flash every two seconds when the vehicle is armed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The indicator will illuminate for three seconds and then go out.
Locks and Security Programming spare keys You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. Tips: • Only use Securilocky keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible. • If you do not have at least 2 previously programmed keys, you must take your vehicle to your authorized Mazda dealer to have the spare key(s) programmed. 1.
Locks and Security 8. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position. Keep the ignition in the 3 (ON) position for at least one second but not more than 10 seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out.
Locks and Security Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the transmitter. • Unlock the doors with a key. control on your remote entry • Pressing the control on the remote entry transmitter. This will disarm the system only if the alarm is sounding.
Seating and Safety Restraints Seating and Safety Restraints SEATING Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.
Seating and Safety Restraints Adjustable head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Push side control and push down on head restraint to lower it.
Seating and Safety Restraints Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints Move the control in the directions shown to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. When activated, they will turn off automatically after 10 minutes or when the ignition is turned to the OFF position.
Seating and Safety Restraints Push control to lower head restraint. Reclining the second row seatback Locate the release strip located on the outboard side of the seat cushion bottom and lift gently to allow the seatback to be adjusted to the desired position. WARNING: Sitting in a reclined position while the vehicle is moving is dangerous because you don’t get the full protection from seat belts.
Seating and Safety Restraints 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control. 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback.
Seating and Safety Restraints 6. Rotate seatback down into load floor position. WARNING: Make sure seat belt buckle heads are not trapped underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. NOTE: Make sure the floor is clear of all objects before folding the seatback. Returning the rear seats to upright position 1.
Seating and Safety Restraints 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs. To remove the rear cushion 1. Pull the Yellow tab 2. Pull the cushion to the outboard side of the vehicle. To install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2.
Seating and Safety Restraints Folding down rear seats (bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control on each side of the seat to release the locks. 4. Flip seat forward.
Seating and Safety Restraints 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE:When the seatback release strap is pulled use your other hand to guide the seatback. 6. Rotate seatback down into load floor position.
Seating and Safety Restraints To remove the rear cushion 1. Pull the Yellow tab 2. Pull the cushion so that the rods remove from the locking tabs. To install the rear cushion 1. Push the cushion so that the rods fit into the locking tabs. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Seating and Safety Restraints • This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. WARNING: All safety belts should be checked for proper function. Additionally, if the front air bags have deployed, the front pretensioners have also deployed and both front restraints must be replaced.
Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and Safety Restraints How to use the automatic locking mode (Outboard front passenger seating position only) for use with child safety seats • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. WARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Front safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Seating and Safety Restraints The driver and front outboard passenger safety belt systems (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in the activation of the safety belt pretensioners. Refer to the Safety belt maintenance section in this chapter. WARNING: Failure to replace both front restraints under the above conditions could result in severe personal injuries in the event of a collision.
Seating and Safety Restraints Rear seat lap belts Adjusting the center lap belt The lap belt does not adjust automatically. WARNING: The lap belts should fit snugly and as low as possible around the hips, not around the waist. Failure to position the lap belt correctly may cause serious injury in an accident. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from).
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints Reasons given... 9Seat belts don’t work9 9Traffic is light9 9Belts wrinkle my clothes9 9The people I’m with don’t wear belts9 9I have an air bag9 9I’d rather be thrown clear9 Consider... Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around.
Seating and Safety Restraints all automatic locking retractors on all outboard seating positions as well as the automatic locking mode for child safety seats on the passenger front belt.
Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and Safety Restraints WARNING: Do not put anything on or over the air bag module including hands or feet. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. WARNING: Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint Systems or its fuses. See your authorized Mazda dealership.
Seating and Safety Restraints WARNING: Air bags can kill or injure a child in a child seat NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Secure the seat and the child in it properly.
Seating and Safety Restraints hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control.
Seating and Safety Restraints A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beep sounds will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your authorized Mazda dealership immediately.
Seating and Safety Restraints WARNING: Side Air Bag Storage Areas: Attaching things to the seat in such a way as to cover the outboard side of the seat in any way is dangerous. In an accident the object could interfere with the side air bag, which inflates from the outboard side of the front seats, impeding the added protection of the side air bag system or redirecting the air bag in a way that is dangerous. Furthermore, the bag could be cut open spewing exhaust.
Seating and Safety Restraints WARNING: Modification of the Supplemental Restraint System: Modifying the components or wiring of the supplemental restraint system is dangerous. You could accidentally activate it or make it inoperable. Don’t make any modifications to the supplemental restraint system. This includes installing trim, badges, or anything else over the air bag storage areas. It also includes installing extra electric equipment on or near system components or wiring.
Seating and Safety Restraints How does the side air bag system work? The side air bag system (if equipped) consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used for the front air bags. • The two side sensors are located on the lower portion of the b-pillar.
Seating and Safety Restraints WARNING: If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions NOTE: You are required to use safety restraints for children in the U.S. and Canada.
Seating and Safety Restraints WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying air bag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side air bag in a moderate collision. Whenever possible, always secure a child, 12 years or younger, in the rear seat, with an appropriate child restraint system for the child’s age and size.
Seating and Safety Restraints • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? WARNING: Booster seats must be installed only in seating positions equipped with a combination lap/shoulder belt. Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride. WARNING: Follow all instructions provided by the manufacturer of the booster seat.
Seating and Safety Restraints • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and Safety Restraints Check to make sure the child seat is properly secured before each use. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. 4. Clip the tether strap to the anchor as shown.
Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor.
Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. The LATCH anchors are below the locator symbols on the seatback. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Driving Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. Preparing to start your vehicle Engine starting is controlled by the powertrain control system.
Driving WARNING: If you smell exhaust fumes inside your vehicle, have your authorized Mazda dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your authorized Mazda dealership.
Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). O/D OFF BRAKE CHECK FUEL CAP Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. Note: If the driver’s safety belt is fastened, the illuminate.
Driving 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3 (ON). 2. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up. 3. After idling for a few seconds, apply the brake, shift into gear and drive. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Driving Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision. WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Driving Four-wheel anti-lock brake system (ABS) (if equipped) If the vehicle is equipped with an anti-lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system.
Driving With the ABS light on, the anti-lock brake system is disabled and normal ! braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately by an authorized Mazda dealership.) Using four wheel ABS (if equipped) • In an emergency or when maximum efficiency from the ABS is required, apply continuous force on the brake.
Driving WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Driving PREPARING TO DRIVE YOUR VEHICLE Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increased ground clearance, give the vehicle a higher center of gravity than a passenger car. WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Driving If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Locate the access cover plate to the brake-shift interlock override. It is located on the top of the steering column. 3. Insert a tool (or a screwdriver) into the right-hand side of the brake-shift interlock access cover and remove the cover. 4.
Driving WARNING: Do not drive your vehicle until you verify that the brakelamps are working. Failure to check the brakelights and subsequent use of the brakes may result in a rear-end collision. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevents the front wheels from rotating. R D21 ODO WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving Overdrive — column mounted gearshift with O/D off switch The Overdrive position with the O/D OFF switch not depressed is the R D21 normal driving position for this ODO automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy. Overdrive may not be appropriate for certain terrains.
Driving If the O/D OFF indicator light is flashing on and off repeatedly when the vehicle is started or does not come on when the O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur. 2 (Second) Use 2 (Second) for start-up on slippery roads or to give you more R D21 engine braking to slow your vehicle ODO on downgrades.
Driving Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed.
Driving 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds. 6. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator pedal. Do not drive with your foot resting on the clutch pedal and do not use the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life.
Driving Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). 1 3 5 2 4 R NOTE: You can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). This is a special lockout feature which prevents you from shifting into R (Reverse) when you downshift from 5 (Fifth). Parking your vehicle 1. Apply the brake and shift into the neutral position. 1 3 5 2 4 R 2.
Driving 3. Shift into 1 (First). 1 3 5 2 4 R 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. FOUR WHEEL DRIVE (4X4) SYSTEM (IF EQUIPPED) 4x4 system general information WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter.
Driving For the lubricant specification and refill capacity of the Power Take-Off Unit and rear axle refer to the Maintenance and specifications chapter. Operating modes of the 4x4 system The 4x4 system functions in two modes: • The 4x4 AUTO mode provides four-wheel drive with full power LOCK delivered to the front axle at all times, and to the rear axle as required for increased traction. This is appropriate for normal on-road operating conditions, such as dry road surfaces, wet pavement, snow and gravel.
Driving The indicator light illuminates when the 4x4 ON mode is engaged. Shifting between 4x4 Auto and ON modes Press the four-wheel drive control to apply power to both axles. When LOCK you activate the control, the indicator light will illuminate in the instrument cluster. When you press the control again, 4x4 AUTO is activated and, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed.
Driving pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may loose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
Driving WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur. WARNING: Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander.
Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. If you must reduce the tire pressure for whatever reason in sand, make sure you re-inflate the tires as soon as possible.
Driving that does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected. “Tread Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Mazda Motor Corporation joins the U.S.
Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t turn and if they aren’t turning, you won’t be able to steer. The front wheels have to be turning in order to steer the vehicle.
Driving • Never drive with chains on the front tires of 4x4 vehicles without also putting them on the rear tires. This could cause the rear to slide and swing around during braking. Tires, Replacement Requirements Do not use a size and type of tire and wheel other than that originally provided by Mazda Motor Corporation because it can affect the safety and performance of your vehicle, which could lead to loss of vehicle control or rollover and serious injury.
Driving Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare). Safe vehicle operation requires your tires to be set at the proper pressure and your vehicle not be overloaded. Periodically inspect the tire treads and remove stones, nails, glass or other objects that may be wedged in the tread grooves.
Driving and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Driving GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the driver’s door or door pillar. The total load on each axle must never exceed its GAWR.
Driving WARNING: Exceeding the Safety Certification Label axle weight rating limits could result in substandard vehicle handling, performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer.
Driving WARNING: Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.
Driving Trailer towing puts additional loads on your vehicle’s engine, transaxle, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: • Be sure to locate all the warnings supplied by the trailer rental or sales company and study the unique requirements of each trailer you intend to tow. • Stay within your vehicle’s load limits.
Driving 4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR Trailer Weight Maximum - kg (lbs.) Range - kg (lbs.) frontal area of trailer - m2 (ft)2 2.0L w/manual 1,932 (4,260) 453 (1,000) 2.2 (24) transmission 3.0L 2,477 (5,460) 907 (2,000) 2.2 (24) w/automatic transmission 3.0L 3,175 (7,000) 1, 587 (3,500) 2.8 (30) w/automatic transmission and towing package Notes: For high altitude operation, reduce GCW by 2% per 100 meters (300 ft.) elevation.
Driving Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners.
Driving • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the “Scheduled Maintenance” section for more information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination.
Driving RECREATIONAL TOWING An example of “recreational towing” is towing your vehicle behind a motorhome. If your vehicle is automatic transmission equipped, with a 4x2 (front-wheel drive only) configured powertrain, “recreational towing” is permitted by trailering the vehicle with its front wheels on a dolly. This protects the transmission’s internal mechanical components from potential lack of lubrication damage.
Roadside Emergencies Roadside Emergencies HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is off. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside Emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside Emergencies 160 Fuse/Relay Location 5 Fuse Amp Rating 5A 6 10A 7 10A 8 10A 9 3A 10 20A 11 10A 12 13 14 15 5A — 20A 15A 16 10A 17 18 15A 5A 19 10A Passenger Compartment Fuse Panel Description ABS unit (EVAC & FILL), ASC unit, Restraints Control Module (RCM), ASC main SW to ASC unit, Clock spring switch Flasher unit, Reversing lamps, Park Aid Module (PAM) Passive Anti-theft Transceiver (PATS), RCM, EEC fuse Cluster, Shift lock relay (coil), O/D signal to PCM, GEM, E/C autolamp
Roadside Emergencies Fuse/Relay Location 20 Fuse Amp Rating 15A 21 22 23 24 10A 15A 20A 15A 25 26 30A 30A 27 10A ACC — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Roadside Emergencies WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies Fuse/Relay Location FUEL DIODE DIODE H/L RELAY MICRO HTD SEATS INJ Fuse Amp Rating 20A* — — — MAIN ALT (DRL) 120A 15A* 15A* 30A 30A** PWR 1 FOG A/C (ABS) 15A*(DRL2) 10A(HLEV) 15A* 20A* 15A* 25A* PWR 2 IG MAIN HTR BTN 1 15A* 40A** 40A** 40A** (ABS) BTN 2 60A** 40A** (DRL2) (HLEV) Power Distribution Box Description Fuel pump, EEC (FPM) — — Headlamp (high/low, right/left relay) Heated seats (if equipped) EEC (VPWR), EVR, MAF, IAC, Bulkhead, HEGO fuse Main Alternator/ Regulator
Roadside Emergencies Fuse/Relay Location MAIN FAN EEC MAIN ISO FUEL PUMP ISO MAIN FAN ISO Fuse Amp Rating 40A** (2.0 L) 50A(3.0 L) 30A** 40A**(2.0 L) 50A(3.0 L) — — — ADD FAN ISO — DEF RELAY ISO ST RELAY ISO ADD FAN 2 ISO — — — FOG RELAY MICRO A/C RELAY MICRO — EEC relay Fuel pump relay Low-speed fan control relay (2.0L engine) High-speed fan control relay 1 (3.0L engine) High-speed fan control relay 1 (2.0L engine) Low-speed fan control relay (3.
Roadside Emergencies 3. Turn off the air conditioner. WARNING: Steam from an overheated engine is dangerous. The escaping steam could seriously burn you. Open the hood ONLY after steam is no longer escaping from the engine. 4. Check whether coolant or steam is escaping from under the hood or from the engine compartment. • If steam is coming from the engine compartment:do not go near the front of the vehicle. Stop the engine, then turn the ignition switch to the ON position without starting the engine.
Roadside Emergencies WARNING: If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside Emergencies WARNING: Changing a tire is dangerous if not done properly. The vehicle can slip off the jack and seriously injure you or someone. Be sure to follow the directions for changing a tire, and never get under a vehicle that is supported only by a jack. 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine OFF. 3. Block the diagonally opposite wheel.
Roadside Emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front jacking notches are located under the front suspension arm. • Rear jacking notches are located under the rear trailing arm.
Roadside Emergencies 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground. Never use the differentials as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured. WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Roadside Emergencies 10. Remove the jack and fully tighten the lug nuts in the order shown. 1 3 4 5 NOTE: To stow the full size flat tire in the cargo floor, the long spare tire rod in the tool bag needs to be installed. 11. Using the lug wrench, remove the spare tire rod from the cargo floor and install the longer spare tire rod. 12. Put flat tire and tool bag with jack handle, lug nut wrench and spare tire rod away. Make sure jack is fastened so it does not rattle when you drive.
Roadside Emergencies Wheel lug nut torque specifications Retighten the lug nuts to the specified torque at 800 km (500 miles) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* Nm Lb-ft M12 x 1.5 113-153 84-114 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Mazda recommended replacement fasteners.
Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. • Use only a 12–volt supply to start your vehicle.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure.
Roadside Emergencies In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles).
Customer Assistance Customer Assistance CUSTOMER ASSISTANCE (U.S.A.) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance If you live outside the U.S.A., please contact your nearest Mazda Distributor. CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer.
Customer Assistance Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer’s service facilities. personnel and equipment. We urge you to follow the above three steps in sequence therefore for most effective results. MEDIATION/ARBITRATION PROGRAM Occasionally a customer concern cannot be resolved through Mazda’s Customer Satisfaction Program. If after exhausting procedures in this manual, your concern is still not resolved, you have another option.
Customer Assistance Provincial Administrators may be reached locally as listed below: Province/Territory CAMVAP Number British Columbia & Yukon (604) 681–0312 Territories Alberta & Northwest Territories (403) 426–0650 Saskatchewan (306) 352–9259 Manitoba (204) 942–7166 Ontario (416) 596–8824 Atlantic Canada (902) 422–5413 Quebec (418) 649–1330 REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc.
Customer Assistance CUSTOMER ASSISTANCE (PUERTO RICO) Your complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Customer Assistance MAZDA IMPORTERS/DISTRIBUTORS U.S.A (Importer/Distributor) Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 TEL: 1 (800) 222–5500 (in U.S.A.) (949) 727–1990 (outside U.S.A.) (Distributor in each area) CANADA Mazda Canada, Inc. 305 Milner Avenue, Suite 400 Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P.O.
Customer Assistance AMERICAN SAMOA Polynesia Motors, Inc. P.O. Box 1120, Pago Pago, American Samoa 96799 TEL: (684) 699–1854 ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or safety system; the manufacturer’s warranty doesn’t cover this.
Customer Assistance • California Emission Control Warranty (if applicable) • Replacement Parts and Accessories Limited Warranty • Tire Warranty NOTE: Detailed warranty information is provided with your Mazda portfolio. OUTSIDE THE UNITED STATES Government regulations in the United States require that automobiles meet specific emission regulations and safety standards. Therefore, vehicles built for use in the United States, may differ from those sold in other countries.
Customer Assistance vehicles built for use in Canada could be eligible for exportation to the United States with specific vehicle modifications to comply with the United States Federal Motor Vehicle Safety requirements. Special Note: The above is applicable for permanent import/export situations and not related to travelers on vacation. You may have the following problems if you do take your vehicle outside of Canada: • Recommended fuel may be unavailable.
Customer Assistance If you live outside of the U.S.A., please contact the nearest Mazda Distributor. (See the Mazda Importers/Distributors section of this manual). SERVICE PUBLICATIONS Factory-authorized Mazda service publications are available for owners who wish to do some of their own maintenance and repair. When requesting any of our publications through an Authorized Mazda Dealer, refer to the chart below. If they don’t have what you need in stock, they can order it for you.
Customer Assistance California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 29 000 km (18 000 miles), whichever occurs first: 1. Two or more repair attempts are made on the same nonconformity likely to cause death or serious bodily injury OR 2.
Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as an approved shampoo available from your Mazda dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. • Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning PAINT CHIPS Your dealer has touch-up paint to match your vehicle’s color. Touch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish.
Cleaning • 2.0L DOHC I4 — Zetec Engine • 3.0L DOHC V6 — Duratec Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use One Step Wash and Wax Concentrate, available at your authorized Mazda dealer.
Cleaning WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleaned regularly. If the wiper does not wipe properly, substances on the windshield, rear window or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, tree sap, or other organic contamination.
Cleaning INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags (if equipped): • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Extra Strength Upholstery Cleaner, available at your authorized Mazda dealer. • If grease or tar is present on the material, spot-clean the area first with Spot and Stain Remover, available at your authorized Mazda dealer. • Never saturate the seat covers with cleaning solution.
Cleaning MAZDA CAR CARE PRODUCTS Your Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use these products or products of equivalent quality.
Maintenance and Specifications Maintenance and Specifications INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer. Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.
Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 6 12 18 24 30 36 42 48 54 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 60 66 72 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 6 12 18 24 30 36 42 48 54 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 60 66 72 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.
Maintenance and Specifications SCHEDULE 2 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ENGINE Engine valve clearance (
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) Engine coolant (yellow) Replace at first 160,000 km (100,000 miles) or 60 months; after that, every 80,000 km (50,000 miles) or 36 months I I I I I I I I I I I I Engine coolant level ELECTRICAL SYS
Maintenance and Specifications at the recommended time or mileage (kilometrage) period to ensure long-term reliability. *2 If this component has been submerged in water, the oil should be changed. OWNER MAINTENANCE SCHEDULE The owner or a qualified service technician should make these vehicle inspections at the indicated intervals to ensure safe and dependable operation. Bring any problem to the attention of an Authorized Mazda Dealer or qualified service technician as soon as possible.
Maintenance and Specifications PRECAUTIONS WHEN SERVICING YOUR VEHICLE WARNING: A hot engine is dangerous. If the engine has been running, parts of the engine compartment can become very hot. You could be burned. Don’t inspect the coolant system or add coolant when the engine is hot. • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1 2 9 3 8 7 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake/Clutch fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8. Engine oil dipstick 9.
Maintenance and Specifications 3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. WARNING: If you operate your vehicle in temperatures below 4.5° C (40° F), use washer fluid with antifreeze protection.
Maintenance and Specifications 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.0L DOHC I4 Zetec engine ADD FULL MIN MAX • 3.
Maintenance and Specifications 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN-MAX or ADD-FULL marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range. • 2.0L DOHC I4 Zetec engine • 3.0L DOHC V6 Duratec engine • Oil levels above the MAX or FULL mark may cause engine damage.
Maintenance and Specifications 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed. Engine oil and filter recommendations SAE 5W-20 engine oil is recommended Look for this certification trademark. Use SAE 5W-20 motor oil certified for gasoline engines by the American Petroleum Institute (API).
Maintenance and Specifications BATTERY Your vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications RN LE TU AD RE transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance section for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications The cooling system in your vehicle is filled with yellow-colored Mazda Premium Engine Coolant meeting Mazda Specifications. To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: • Add Mazda Premium Engine Coolant. • Do not mix different colors or types of coolant. Verify the type of coolant in your vehicle. Make sure the correct coolant is used.
Maintenance and Specifications 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5.
Maintenance and Specifications Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%.
Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.
Maintenance and Specifications WARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Avoid inhaling fuel vapors.
Maintenance and Specifications WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Maintenance and Specifications NOTE: Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized Mazda dealer to prevent any engine damage. Fuel quality NOTE: If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline.
Maintenance and Specifications When fueling your vehicle: 1. Turn the engine off. 2. Pull the fuel filler door release handle to open the fuel filler door. 3. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 4. Pull to remove the cap from the fuel filler pipe. 5. To install the cap, align the tabs on the cap with the notches on the filler pipe. 6. Turn the filler cap clockwise 1/8 of a turn until it stops.
Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,600 km (1,000 miles) of driving (engine break-in period).
Maintenance and Specifications 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Multiply liters used by 100, then divide by total kilometers traveled.
Maintenance and Specifications • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter.
Maintenance and Specifications It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine.
Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the service maintenance section for the service interval schedules. If adding fluid is necessary, use only MERCONt ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3.
Maintenance and Specifications The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range, there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of your brake/clutch (if equipped) system could be compromised, seek service from an authorized Mazda dealer immediately.
Maintenance and Specifications Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving.
Maintenance and Specifications Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4.
Maintenance and Specifications AIR FILTER MAINTENANCE Refer to the service maintenance section for the appropriate intervals for changing the air filter element. When changing the air filter element, only use a Genuine Mazda air filter element. WARNING: Don’t drive without an air filter. This could result in excessive engine wear. Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover. 2.
Maintenance and Specifications INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Maintenance and Specifications Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Maintenance and Specifications • PSI: Pounds per square inch, a standard unit of air pressure. • B-pillar: The structural member at the side of the vehicle behind the front door. • Bead area of the tire: Area of the tire next to the rim. • Sidewall of the tire: Area between the bead area and the tread. • Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle.
Maintenance and Specifications 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s guide. If not, contact a local tire dealer.
Maintenance and Specifications four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are marketing codes used at the manufacturer’s discretion. This information is used to contact customers if a tire defect requires a recall. 9. M+S or M/S: Mud and Snow. or AT: All Terrain. or AS: All Season. 10.
Maintenance and Specifications Note: You may not find this information on all tires because it is not required by federal law. The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information than those of “P” type tires; these differences are described below: 1.
Maintenance and Specifications T Information on “T” type tires T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different than RE T SPA/80D16 1IRE this example. 05M 5 T1 4 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge.
Maintenance and Specifications Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns. NOTE: If you are driving the vehicle at its maximum weight load, make sure the tire inflation pressure is correct for the weight load on the tires.
Maintenance and Specifications 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires require higher inflation pressure than the other tires. 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts, bulges or other irregularities.
Maintenance and Specifications • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) vehicles (front tires at top of diagram) 241
Maintenance and Specifications Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. Tire wear Measure and inspect the tire tread on all your tires periodically.
Maintenance and Specifications Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If you vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
Maintenance and Specifications Follow these guidelines when using snow tires and traction devices: • SAE class “S” cables should be used on front axle for P235/70R16 tires. With P215/70R16 tires, SAE class “S” cables can be used on both the front and rear wheels. • Do not use tire chains on aluminum wheels. Chains may chip the wheels. • Install cables or chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously.
Maintenance and Specifications Fluid Transmission fluid 1 Classification API service GL-4, SAE 75W-90 MERCONt ATF Transfer Case Engine coolant Rear axle lubricant Windshield washer fluid 4 SAE 75W-140 Synthetic Lubricant API service GL-5, SAE 80W-90 Mazda yellow-colored Premium Engine Coolant API service GL-5, SAE 80W-90 Premium Rear Axle Lubricant n/a Application Manual transaxle (2WD) Manual transaxle (4X4) 3.0L engine with Automatic transaxle and oil cooler 4X4 (Automatic) Capacity 2.7L (2.
Maintenance and Specifications 3 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range. 4 Add the coolant type originally equipped in your vehicle. DO NO MIX different colors or types of coolant. DO NOT USE Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant in this chapter.
Maintenance and Specifications VEHICLE DIMENSIONS Dimensions (1) Vehicle height/ Maximum height* (2) Front track / rear (3)Overall width (body) (4) Wheelbase (5)Overall length 4 Door mm (in.) 1,681 (66.2)/1,744 (68.7)* 1,550 1,783 2,620 4,394 (61.0)/1,530 (60.2) (70.2) (103.1) (173.
Maintenance and Specifications 4 5 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Accessories Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident.
Index Index A Axle refill capacities ........................244 ABS (see Brakes) .....................126 Accessory delay ..........................62 B Air bag supplemental restraint system ........................100–101, 105 and child safety seats ............102 description ......................101, 105 disposal ............................105, 109 driver air bag ..................103, 108 indicator light .................104, 109 operation .........................103, 108 passenger air bag ....
Index Cleaning your vehicle engine compartment ..............191 instrument panel ....................193 interior .....................................194 interior trim ............................193 Mazda car care products .......195 plastic parts ............................192 washing ....................................190 waxing .....................................190 wheels ......................................191 wiper blades ............................
Index driving off road .......................140 indicator light .........................139 preparing to drive your vehicle .....................................129 Fuel ............................................217 calculating fuel economy .......222 cap ...........................................220 capacity ...................................244 choosing the right fuel ...........219 comparisons with EPA fuel economy estimates .................224 detergent in fuel .....................
Index K Keys positions of the ignition .........121 L Lamps bulb replacement specifications chart ..................51 cargo lamps ...............................49 daytime running light ...............48 fog lamps ...................................48 headlamps .................................48 headlamps, flash to pass ..........49 instrument panel, dimming .....49 interior lamps .....................50–51 replacing bulbs .......51–52, 54–55 Lane change indicator (see Turn signal) .......................
Index Radio reception .....................42–43 Rear window defroster ...............47 Relays ........................................158 Remote entry system arming and disarming the anti-theft system ......................73 illuminated entry ......................74 locking/unlocking doors ...........70 replacing the batteries .............73 Roof rack .....................................69 S Safety Belt Maintenance ............99 Safety belts (see Safety restraints) .........
Index fluid, refill capacities ..............244 Turn signal ..................................50 Washer fluid ..............................206 V Windows power .........................................61 rear wiper/washer .....................57 Vehicle dimensions ...................247 Vehicle Identification Number (VIN) ..........................................249 Vehicle loading ..........................148 Ventilating your vehicle ...........125 W Warning lights (see Lights) .......
