Table of Contents Introduction 3 Instrument Cluster 8 Warning and control lights Gauges 10 15 Entertainment Systems 17 AM/FM stereo with CD AM/FM stereo with cassette and in-dash six CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control (Cruise control) 17 27 44 44 48 48 50 51 56 56 58 60 61 62 Locks and Security 69 Keys Locks
Table of Contents Driving 120 Starting Brakes Transmission operation Vehicle loading Trailer towing 120 124 128 147 149 Roadside Emergencies 155 Hazard flasher switch Fuses and relays Overheating Jump starting Wrecker towing 155 156 162 169 174 Customer Assistance 176 Reporting safety defects (U.S.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed.
Introduction SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially including but not limited to information such as: • the use of restraint systems including seat belts by the driver and passengers, • information about the performance of various systems and modules in the vehicle, and • information related to engine, throttle, steering, brake or other system status potentially including information related to how the driver operates the vehicle in
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of
Instrument Cluster Headlamp and turn signal control (pg. 48) Fog lamp control* (pg. 48) Power mirror control* (pg. 61) * if equipped 8 Windshield wiper/washer control (pg. 56) Instrument cluster (pg. 10) Speed controls* (pg. 62) Driver air bag Instrument panel (pg. 99) dimmer/dome light control (pg. 49) Hood release handle (pg. 198) Manual tilt steering column lever (pg.
Instrument Cluster Rear window defroster control (pg. 47) Hazard flasher control (pg. 155) Audio system (pg. 17) 4WD control* (pg. 137) Cigarette lighter Climate controls (pg. 44) Auxiliary power point (pg.
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL CAP Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off.
Instrument Cluster It may take a long period of time for the system to detect an improperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and specifications chapter.
Instrument Cluster Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly.
Instrument Cluster Four wheel drive indicator (if equipped): Illuminates when four-wheel drive is engaged, refer to the Driving chapter. Note: If the light continues to flash, have the system serviced. Anti-theft system: Flashes when the Securilocky Passive Anti-theft System has been activated. Refer to SecuriLocky passive anti-theft system in the Locks and Security chapter. Speed control: Illuminates when CRUISE the speed control is activated.
Instrument Cluster GAUGES CHECK FUEL CAP Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Refer to Engine coolant in the Maintenance and Specifications chapter.
Instrument Cluster Odometer: Registers the total kilometers (miles) of the vehicle. Trip odometer: Registers the kilometers (miles) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems AM/FM RADIO WITH COMPACT DISC PLAYER Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running.
Entertainment Systems AM/FM select Ensure that the ignition is in the ACC or ON position for the radio to operate. Press the AM or FM1/2 control to enter radio mode. Band selection Select AM by pressing the AM button and FM1 or FM2 by pressing the FM1/2 button. The selected mode will be indicated. If FM stereo is being received, ST will be displayed. Note: If the FM broadcast signal becomes weak, reception automatically changes form STEREO to MONO for reduced noise and the ST incdicator will go out.
Entertainment Systems Turn the TUNE control to the left for a lower frequency. Turn the TUNE control to the right for a higher frequency. Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disable scan mode. Scan function in CD mode Press the SCAN control during CD play to hear the first ten seconds of each track.
Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the audio control until TREB is displayed. Turn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the audio control until BASS appears. Turn the control to increase (right) or decrease (left) the amount of bass output.
Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers.
Entertainment Systems Press the audio control until MID appears in the display. Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display. Release the TUNE control when the desired level is reached. NOTE: Approximately 5 seconds after selecting any mode, the volume function will be automatically selected. To reset the mid-range, press the TUNE control for approximately 2 seconds.
Entertainment Systems Starting autoset memory preset 1. Press the AM or FM1/2 control to select a frequency. 2. Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. 3. When the first six strong stations are filled, the strongest station will start playing. 4. Press the AUTO-M (Auto memory) control to select from the stored stations. One stored station will be selected and played each time the control is pressed. The frequency and channel number will be displayed.
Entertainment Systems Press the VOL (Volume) control to stop cassette play. CD select To begin CD play: 1. Insert a CD into the slot, label side up. The system will auto-load the CD and begin play after a short pause. The disc number and the track number will illuminate in the display. Rewind The rewind control works in CD mode. In CD mode, press and hold the rewind control to reverse through a track at a high speed.
Entertainment Systems Track search Track search works in CD mode. on the TRACK control Press the to skip forward to the beginning of the next track. on the TRACK control Press the to skip back to the beginning of the current track. Disc search Disc search works in CD mode. Press the DISC up control to skip forward to the beginning of the next CD. Press the DISC down control to skip back to the beginning of the previous CD. Ejecting a CD The eject feature works in CD mode. 1.
Entertainment Systems Random play in CD mode Press the RDM control during play. RDM will illuminate in the display. The next selection will be randomly selected. To disengage random play, press the RDM control again. Setting the clock The clock can be set at any time when the ignition switch is in the ACC or ON position. 1. Press and hold the CLOCK control for approximately 2 seconds until a beep is heard. The clock’s current time will flash. 2. Press SCAN on the hour set control to adjust the hours. 3.
Entertainment Systems Press the CLOCK control to alternate the display. NOTE: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode. AM/FM RADIO WITH CASSETTE TAPE AND COMPACT DISC PLAYER/CHANGER (IN-DASH CD CHANGER) Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off.
Entertainment Systems Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE: Once the system is turned off, press the VOL control again to listen to the frequency last tuned to. AM/FM select Ensure that the ignition is in the ACC or ON position for the radio to operate. Press the AM or FM1/2 control to enter radio mode.
Entertainment Systems Press the TUNE control to select the desired function. Turn the TUNE control to adjust the desired levels. Refer to Treble adjust for specific instructions on level adjustments. The TUNE control will also work in radio mode to manually increase or decrease the frequency. Turn the TUNE control to the left for a lower frequency. Turn the TUNE control to the right for a higher frequency. Scan function The scan function works in radio and CD mode.
Entertainment Systems NOTE: If the unit is left in scan mode, normal play will resume where scan was selected. Seek function The seek function control works in radio mode. Seek function in radio mode Press and momentarily hold the SEEK control. • Press to find the next listenable station up the frequency band. • Press to find the next listenable station down the frequency band. NOTE: If you continue to press and hold the control, the frequency will continue changing without stopping.
Entertainment Systems Press the audio control until BASS appears. Turn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Entertainment Systems Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Your vehicle may be equipped with a mid-range adjust. The TUNE control allows you to adjust the mid-range levels. Press the audio control until MID appears in the display. Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM control. 2. Select a station. 3. Press and momentarily hold the desired preset control until a beep is heard. The preset control number will illuminate in the display.
Entertainment Systems NOTE: If the power supply is interrupted, (fuse blows or the battery is disconnected), the preset channels will be canceled. Tape select (if equipped) To begin tape play, insert a cassette tape into the cassette slot, with the open edge facing the right. Once inserted, the cassette tape will automatically begin play and TAPE will appear in the display. At the end of the cassette tape, the unit will automatically reverse the cassette tape play.
Entertainment Systems Tape direction select Press the PROG RDM control to play the alternate side of a tape. NOTE: When the end of the cassette is reached, the audio system will automatically reverse play. Repeat play The repeat play feature works in tape and CD modes and allows you to listen to a selection repeatedly. Repeat play in tape mode Press the RPT control during play. RPT will illuminate in the display. The current selection will be repeated. To disengage repeat play, press the RPT control again.
Entertainment Systems Track search Track search works in CD mode. on the TRACK control Press the to skip forward to the beginning of the next track. Press the on the TRACK control to skip back to the beginning of the current track. Disc search Disc search works in CD mode. Press the DISC up control to skip forward to the beginning of the next CD. Press the DISC down control to skip back to the beginning of the previous CD. DolbyT noise reduction Dolbyt noise reduction operates only in tape mode.
Entertainment Systems APC in tape mode Press the APC control to advance to the beginning of the next selection. Press the APC control to reverse to the beginning of the current selection. To disengage APC, press the APC control again. If APC detects 15 seconds of blank space, it will automatically advance the tape to the next selection. NOTE: APC may not operate properly if: • A tape was recorded at a low level. • A tape has long, silent intervals. • A tape is a live recording.
Entertainment Systems Inserting CDs into desired tray number 1. Press and hold the LOAD control until a beep is heard. 2. Press the memory preset control for the deisred CD tray within 5 seconds after the beep is heard. 3. When IN is displayed, insert the CD. NOTE: The CD cannot be inserted to the desired tray number if the number is already occupied. Eject feature The eject feature works in both tape and CD mode. Ejecting a tape Press the control to stop and eject a tape.
Entertainment Systems Multiple ejection 1. Press and hold the CD eject control for approximately 2 seconds until a beep is heard. 2. Wait approximately 5 seconds or press the CD eject control again within 5 seconds after the beep is heard. 3. Remove the CD. The next CD will then be ejected. NOTE: • Cds will be ejected in numerical order, lowest number first. • All CDs in the tray will be ejected continuously. • Cds can be ejected when the ignition switch is OFF.
Entertainment Systems 2. Press SCAN on the hour set control to adjust the hours. 3. Press AUTO-M on the minute set control to adjust the minutes. 4. Press the CLOCK control again to start the clock. NOTE: If the power supply to the unit is interrupted (if the fuse blows or the vehicle’s battery is disconnected), the clock will need to be reset.
Entertainment Systems • A disc with format and dimensions not within industry standards is inserted. CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Entertainment Systems • Do not stick paper or tape on the CD. Avoid scratching the reverse side of the CD (the side without a label). • Dust, finger smudges, and dirt can decrease the amount of light reflected from the signal surface, thereby effecting sound quality. Gently wipe a soiled CD with a soft cloth from the center to the edge. • Do not use record sprays, antistatic agents, or household spray cleaners.
Entertainment Systems Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor will operate in all modes , , and .
Climate Controls • MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers.
Climate Controls Operating tips • In humid weather conditions, place the climate control system in Defrost mode before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Climate Controls 4. Direct the outer panel vents towards the side windows. 5. To increase airflow to the outer panel vents, close the central panel vents. WARNING: Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER CONTROL The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. OFF BATTERY SAVER Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beams position.
Lights High beams After turning the headlamps on, push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. OFF Flash to pass Pull toward you slightly to activate and release to deactivate. OFF INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim.
Lights AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. OFF INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position.
Lights With the control in the middle position, the dome lamp will illuminate whenever any door is opened. If any door has been opened from the outside, the lamp will remain on for 15 seconds after the door is shut. The map lamp controls (without moon roof) are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps. If equipped with a moon roof, the map lamps are located on the moon roof control panel.
Lights Function Number of bulbs Trade number Park/turn lamps (front) 2 3157 AK (amber) Headlamps 2 9003 Rear stop/tail lamps 2 3157K Rear turn lamps 2 3156K Rear license plate lamps 2 3156K/168 Backup lamp 2 3156K Rear/turn/sidemarker 2 916NA (amber) Fog lamp (if equipped) 2 899 Cargo lamp 1 211-2 Interior overhead lamp 1 912 (906) Front door courtesy lamp 1 168 Map lamps 2 168 (T10) Ashtray lamp 1 161 All replacement bulbs are clear in color except where noted.
Lights Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hands could cause the bulb to break the next time the headlamps are operated. Always wear safety glasses while handling bulbs. NOTE: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 7. Insert the glass end of the new bulb into the headlamp assembly.
Lights 5. Pull the bulb straight out of the socket and push in the new bulb. 6. To complete installation, follow the removal procedure in reverse order. Replacing front parking/turn signal lamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. The position lamps are located on the bottom half of each headlamp. 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb socket from the lamp assembly by turning counterclockwise. 5.
Lights Replacing license plate lamp bulbs 1. Remove two screws and the license plate lamp assembly (located above the license plate) from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly turning it clockwise, 5. Install the lamp assembly on liftgate with two screws. Replacing high-mount brake lamp bulbs For bulb replacement, see an authorized Mazda dealer.
Driver Controls MULTI—FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF. Mist function: To mist, push control up from the OFF position and release to get one wipe. Windshield washer: To activate the windshield washer, pull control toward you.
Driver Controls For normal speed rear wiper operation, rotate control upward to ON. To activate the rear washer, rotate the control to the position and release. Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Driver Controls MANUAL TILT STEERING COLUMN To adjust the steering wheel: 1. Pull down and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Pull the steering wheel release control up. This will lock the steering wheel in position. WARNING: Never adjust the steering wheel when the vehicle is moving. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.
Driver Controls Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the Velcro pad from the storage compartment door. • Place Velcro on aftermarket transmitter opposite of actuator control. • Install the transmitter on to storage compartment door aligning the actuator control with the rubber plunger. • Close the door and press the storage compartment door to activate the transmitter.
Driver Controls CARGO AREA AUXILIARY POWER POINT An additional auxiliary power point is located in the cargo area. WARNING: Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. POWER WINDOWS The ignition must be in the ON position to adjust the power windows. Press and hold the bottom part of the rocker switch to open the window.
Driver Controls To lock out all the window controls except for the driver’s window press the right side of the control. NOTE: The window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls. Accessory delay With accessory delay, power windows and moonroof operate for up to ten minutes after the ignition switch is turned from the ACC or ON to the OFF position or until any door is opened.
Driver Controls Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. ON OFF 3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. RSM SET ACC CST Note: • Vehicle speed may vary momentarily when driving up and down a steep hill.
Driver Controls Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 48 km/h (30 mph). RSM SET ACC CST Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control.
Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control. RSM SET ACC CST Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicles previously set speed. • Press the speed control OFF control. ON Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
Driver Controls MOON ROOF (IF EQUIPPED) To operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time. • To close, press and hold the front portion of the control. To operate the moon roof vent position: • To open, press and hold the front portion of the control. This will open the vent.
Driver Controls To install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels. To operate the shade: 1. Grasp the pull tube at the rearward edge of the shade and pull rearward. 2. Secure both ends of the pull tube in the retention slots located on the rear trim panels. WARNING: Ensure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is not securely installed.
Driver Controls WARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. LUGGAGE RACK The maximum load for the roof rack is 44 kg (100 lbs), evenly distributed on the crossbars.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLocky Passive Anti-Theft System for more information. POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. Door key unlocking/locking Unlocking the doors 1. Turn the key in the door cylinder to unlock the driver’s door.
Locks and Security Locking the doors 1. Turn the key in the door cylinder to lock all the doors. The park lamps will flash once and the perimeter alarm (if equipped) will be start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. 2. Turn the key in the door cylinder again within three seconds to confirm that all the doors are closed and locked.
Locks and Security REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Locks and Security Locking the doors 1. Press and release to lock all the doors. The park lamps will flash once and the perimeter alarm (if equipped) will be start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. 2. Press and release again within three seconds to confirm that all the doors are closed and locked.
Locks and Security 3. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. 4. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.
Locks and Security 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.
Locks and Security Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine.
Locks and Security • The indicator will illuminate for three seconds and then go out. • If the indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your authorized Mazda dealer. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to a dealership. The key codes need to be erased from your vehicle and new coded keys and key codes will need to be programmed.
Locks and Security 1. Insert a previously programmed coded key into the ignition. 2. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position. Keep the ignition in the 3 (ON) position for at least one second, but no more than 10 seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the coded key from the ignition. 4. Within ten seconds, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position.
Locks and Security PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting. Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the headlamps, parking lamps and will sound the horn.
Seating and Safety Restraints SEATING Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints Adjustable head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Push side control and push down on head restraint to lower it.
Seating and Safety Restraints Adjusting the front power seat (if equipped) WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the outboard side of the seat cushion. Move the front of the control up or down to raise or lower the front portion of the seat cushion.
Seating and Safety Restraints Heated seats (if equipped) To operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. When activated, they will turn off automatically after 10 minutes or when the ignition is turned to the OFF position. The heated seat LED in the dual electronic automatic temperature control (DEATC) will illuminate when activated.
Seating and Safety Restraints Push control to lower head restraint. Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control.
Seating and Safety Restraints 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback. 6. Rotate seatback down into load floor position.
Seating and Safety Restraints NOTE: Make sure the floor is clear of all objects before folding the seatback. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. While holding the seatback, pull the release and push seatback backward into the desired position. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3.
Seating and Safety Restraints To remove the rear cushion 1. Pull the Yellow tab 2. Pull the cushion to the outboard side of the vehicle. To install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. Folding down rear seats (bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage.
Seating and Safety Restraints 3. Pull the seat release control on each side of the seat to release the locks. 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback. 6. Rotate seatback down into load floor position.
Seating and Safety Restraints Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs.
Seating and Safety Restraints To install the rear cushion 1. Push the cushion so that the rods fit into the locking tabs. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained.
Seating and Safety Restraints WARNING: In a rollover crash, an unbelted person is significantly more likely to die or be seriously injured than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm.
Seating and Safety Restraints WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked according to the procedures in Workshop Manual. WARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Combination lap and shoulder belts 1.
Seating and Safety Restraints sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode (outboard front passenger seating position only) for use with child safety seats The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked.
Seating and Safety Restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. WARNING: After any vehicle collision, the front passenger outboard seat belt system must be checked by an authorized Mazda dealership to verify that the “automatic locking retractor” feature for child seats is still functioning properly.
Seating and Safety Restraints WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions.
Seating and Safety Restraints WARNING: Improper disposal of the pretensioner system or a vehicle with non-deactivated pretensioners is dangerous. Unless all safety procedures are followed, injury could result. Ask an authorized Mazda Dealer how to safely dispose of the pretensioner system or how to scrap a front pretensioner-equipped vehicle.
Seating and Safety Restraints To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use to keep the belt away from door openings and available after unfolding the seats. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...
Seating and Safety Restraints Reasons given... 9Crashes are rare events9 Consider... 36,700 crashes occur every day. The more we drive, the more we are exposed to 9rare9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 9I’m not going far9 3 of 4 fatal crashes occur within 25 miles of home. 9Belts are Safety belts are designed to enhance comfort.
Seating and Safety Restraints WARNING: Always wear the safety belt. Do not be tempted to sit on top of the belt to fool police or to defeat the warning system. The safety belt and safety belt warning system are there to protect your life. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. NOTE:If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection.
Seating and Safety Restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 4 3 2 H C 1 5 6 RPM X 1000 7 60 8 40 60 80 100 80 120 100 4x4 160 MPH 180 km/h 120 AM/FM SCAN 140 40 20 20 TAPE CD LOAD F CLOCK E TUNE SEEK DISC AUTO-M PRO PUSH AUDIO CONT PUSH POWER VOL 1 TR/APC 2 RPT 3 4 REW 5 RDM/BS 6 TR/APC FF RSM ON LOCK SET ACC OFF CST OFF A/C MAX A/C Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work wi
Seating and Safety Restraints WARNING: National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module. WARNING: Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably.
Seating and Safety Restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. WARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints • diagnostic module • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and Safety Restraints Side air bag system (if equipped) WARNING: Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. This is dangerous. In an accident, the object could interfere with the air bag inflation and injure the occupants.
Seating and Safety Restraints WARNING: Seating Position with Side Air Bags Sitting too close to the side air bag storage compartments or placing hands on them is extremely dangerous. A side air bag inflates with great force and speed directly out of the outboard shoulder of the front seat and expands along the front door on the side the car is hit.
Seating and Safety Restraints WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
Seating and Safety Restraints WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags.
Seating and Safety Restraints WARNING: Do not leave children, unreliable adults, or pets unattended in your vehicle. WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying air bag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side air bag in a moderate collision.
Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? WARNING: Booster seats must be installed only in seating positions equipped with a combination lap/s
Seating and Safety Restraints Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs. The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and Safety Restraints • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and Safety Restraints Check to make sure the child seat is properly secured before each use. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. 4. Clip the tether strap to the anchor as shown.
Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor.
Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. Preparing to start your vehicle Engine starting is controlled by the powertrain control system.
Driving WARNING: If you smell exhaust fumes inside your vehicle, have your authorized Mazda dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your authorized Mazda dealership.
Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). O/D OFF BRAKE CHECK FUEL CAP Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. Note: If the driver’s safety belt is fastened, the illuminate.
Driving 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try, turn the key OFF and wait 10 seconds and try again.
Driving WARNING: If you ever smell exhaust fumes of any kind inside your vehicle, have your authorized Mazda dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and result in accident or death. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision.
Driving squeal or groan noises when the brakes are applied. Such noises are usually heard during the first few brake applications in the morning; however, they may be heard at any time while braking and can be aggravated by environmental conditions such as cold, heat, moisture, road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by an authorized Mazda dealership.
Driving ABS warning lamp ABS (if equipped) The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal ! braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! BRAKE WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle.
Driving PREPARING TO DRIVE YOUR VEHICLE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances.
Driving If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Locate the access cover plate to the brake-shift interlock override. It is located on the top of the steering column. 3. Insert a tool (or a screwdriver) into the right-hand side of the brake-shift interlock access cover and remove the cover. 4.
Driving WARNING: Do not drive your vehicle until you verify that the brakelamps are working. Failure to check the brakelights and subsequent use of the brakes may result in a rear-end collision. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevents the front wheels from rotating. R D21 ODO WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving Overdrive — column mounted gearshift with O/D off switch The Overdrive position with the O/D OFF switch not depressed is the R D21 normal driving position for this ODO automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy. Overdrive may not be appropriate for certain terrains.
Driving If the O/D OFF indicator light is flashing on and off repeatedly when the vehicle is started or does not come on when the O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur. 2 (Second) Use 2 (Second) for start-up on slippery roads or to give you more R D21 engine braking to slow your vehicle ODO on downgrades.
Driving Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. MANUAL TRANSAXLE OPERATION (IF EQUIPPED) USING THE CLUTCH Vehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed.
Driving 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds. 6. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator pedal. Do not drive with your foot resting on the clutch pedal and do not use the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life.
Driving REVERSE Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle. Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). 1 3 5 2 4 R NOTE:You can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse).
Driving 3. Shift into 1 (First). 1 3 5 2 4 R 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. FOUR WHEEL DRIVE (4X4) SYSTEM (IF EQUIPPED) 4x4 system general information WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter.
Driving For the lubricant specification and refill capacity of the Power Take-Off Unit and rear axle refer to the Maintenance and specifications chapter. Operating modes of the 4x4 system The 4x4 system functions in two modes: • The 4x4 AUTO mode provides four-wheel drive with full power LOCK delivered to the front axle at all times, and to the rear axle as required for increased traction. This is appropriate for normal on-road operating conditions, such as dry road surfaces, wet pavement, snow and gravel.
Driving The indicator light illuminates when the 4x4 ON mode is engaged. Shifting between 4x4 Auto and ON modes Press the four-wheel drive control to apply power to both axles. When LOCK you activate the control, the indicator light will illuminate in the instrument cluster. When you press the control again, 4x4 AUTO is activated and, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed.
Driving pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may loose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
Driving WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur. WARNING: Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander.
Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. If you must reduce the tire pressure for whatever reason in sand, make sure you re-inflate the tires as soon as possible.
Driving Driving through deep water may damage the transmission. If the rear axle is submerged in water, the axle lubricant should be checked and changed, if necessary. The rear axle is filled with a lubricant that does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected.
Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t turn and if they aren’t turning, you won’t be able to steer. The front wheels have to be turning in order to steer the vehicle.
Driving • Never drive with chains on the front tires of 4x4 vehicles without also putting them on the rear tires. This could cause the rear to slide and swing around during braking. Tires, Replacement Requirements Do not use a size and type of tire and wheel other than that originally provided by Mazda Motor Corporation because it can affect the safety and performance of your vehicle, which could lead to loss of vehicle control or rollover and serious injury.
Driving Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare). Safe operation requires tires that are neither underinflated nor a vehicle which is overloaded. Periodically inspect the tire treads and remove stones, nails, glass or other objects that may be wedged in the tread grooves.
Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
Driving • Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow.
Driving WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle loss of vehicle control, vehicle rollover, and/or personal injury. Special loading instructions for owners of pickup trucks and utility-type vehicles WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter. WARNING: Loaded vehicles may handle differently than unloaded vehicles.
Driving • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to the “Scheduled Maintenance” section of this manual. • Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles).
Driving 4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR Trailer Weight Maximum - kg (lbs.) Range - kg (lbs.) frontal area of trailer - m2 (ft)2 3.0L 2,477 (5,460) 907 (2,000) 2.2 (24) w/automatic transmission 3.0L 3,175 (7,000) 1, 587 (3,500) 2.8 (30) w/automatic transmission and towing package Notes: For high altitude operation, reduce GCW by 2% per 300 meters (100 ft.) elevation.
Driving Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper.
Driving Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the “Scheduled Maintenance” section for more information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Driving RECREATIONAL TOWING An example of “recreational towing” is towing your vehicle behind a motorhome. If your vehicle is automatic transmission equipped, with a 4x2 (front-wheel drive only) configured powertrain, “recreational towing” is permitted by trailering the vehicle with its front wheels on a dolly. This protects the transmission’s internal mechanical components from potential lack of lubrication damage.
Roadside Emergencies HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is off. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside Emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside Emergencies Fuse/Relay Location 6 Fuse Amp Rating 10A 7 10A 8 10A 9 3A 10 11 20A 10A 12 13 14 15 5A — 20A 15A 16 17 18 10A 15A 5A 19 20 10A 15A 21 22 23 10A 15A 20A 158 Passenger Compartment Fuse Panel Description Flasher unit, Reversing lamps, Park Aid Module (PAM) Passive Anti-theft Transceiver (PATS), RCM, EEC fuse Cluster, Shift lock relay (coil), O/D signal to PCM, GEM, E/C autolamp mirror PCM relay (coil), Fan relay 1, 2, 3 (coil), A/C relay (coil) Front wiper motor, Front
Roadside Emergencies Fuse/Relay Location 24 Fuse Amp Rating 15A 25 26 30A 30A 27 10A ACC — Passenger Compartment Fuse Panel Description Stoplamps, High mounted stoplamp, Trailer stoplamp, ABS unit, ASC unit (Brake Pedal Position Switch), PCM, Shift solenoid Power window motors Power door lock motors, GEM (door lock relay coil), Power seat, 4WD relay GEM, Audio, Cluster, Interior lamp, Map lamp, Cargo lamp, Datalink connector Accessory relay Power distribution box The power distribution box is locat
IG MAIN 40A BTN 1 40A MAIN FAN 40/50A ADD FAN 40/50A BTN 2 R DEF 40A 30A MAIN FAN ISO DEF RELAY ISO ADD FAN 2 ISO FUEL PUMP ISO ADD FAN ISO ST RELAY ISO PWR 2 15A (ABS) 25A PWR 1 15A DRL2 15A HLEV 10A A/C 15A (DRL) 15A ALT 15A FOG 20A DIODE FUEL 20A DIODE HTD SEATS 30A EEC MAIN ISO FOG RELAY MICRO (ABS) 60A INJ 30A HTR 40A HEGO 15A (HORN) 15A H/L LH 15A H/L RH 15A EEC 5A H/L RELAY MICRO MAIN 120A A/C RELAY MICRO Roadside Emergencies The high-current fuses are coded as fol
Roadside Emergencies Fuse/Relay Location INJ MAIN ALT (DRL) (DRL2) (HLEV) PWR 1 FOG A/C (ABS) PWR 2 IG MAIN HTR BTN 1 (ABS) BTN 2 MAIN FAN R DEF ADD FAN Fuse Amp Rating 30A** Power Distribution Box Description EEC (VPWR), EVR, MAF, IAC, Bulkhead, HEGO fuse 120A Main 15A* Alternator/ Regulator 15A* Daytime Running Lamps (DRL) unit (feed), DRL relay 15A*(DRL2) DRL module, HLEV 10A(HLEV) 15A* Auxiliary power point 20A* Foglamps, Foglamp indicator 15A* A/C clutch 25A* Anti-Lock Brake System (ABS) SOL, EVA
Roadside Emergencies Fuse/Relay Location EEC MAIN ISO FUEL PUMP ISO MAIN FAN ISO Fuse Amp Rating — ADD FAN ISO — DEF RELAY ISO ST RELAY ISO ADD FAN 2 ISO FOG RELAY MICRO A/C RELAY MICRO Power Distribution Box Description EEC relay — Fuel pump relay — — Low-speed fan control relay (2.0L engine) High-speed fan control relay 1 (3.0L engine) High-speed fan control relay 1 (2.0L engine) Low-speed fan control relay (3.
Roadside Emergencies WARNING: Steam from an overheated engine is dangerous. The escaping steam could seriously burn you. Open the hood ONLY after steam is no longer escaping from the engine. 4. Check whether coolant or steam is escaping from under the hood or from the engine compartment. • If steam is coming from the engine compartment:do not go near the front of the vehicle. Stop the engine, then turn the ignition switch to the ON position without starting the engine.
Roadside Emergencies When driving with the temporary spare tire do not: • use more than one temporary spare tire at a time • exceed 80 km/h (50 mph) or drive further than 3 200 km (2 000 miles) total under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains • try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Use of a temporary spare tire at any one wheel
Roadside Emergencies • use tire chains • drive through an automatic car wash, because of the vehicle’s reduced ground clearance • try to repair the temporary spare tire or remove it from its wheel rim • use the wheel for any other type of vehicle Tire change procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R (Reverse) (manual transaxle).
Roadside Emergencies 4. Lift the cargo cover and remove the tool bag with jack handle, lug nut wrench and long spare tire rod and spare tire from the wheel well. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front jacking notches are located under the front suspension arm.
Roadside Emergencies • Rear jacking notches are located under the rear trailing arm. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground. Never use the differentials as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured. WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire.
Roadside Emergencies 9. Lower the wheel by turning the jack handle counterclockwise. 10. Remove the jack and fully 1 tighten the lug nuts in the order shown. 3 4 5 NOTE: To stow the full size flat tire in the cargo floor, the long spare tire rod in the tool bag needs to be installed. 11. Using the lug wrench, remove the spare tire rod from the cargo floor and install the longer spare tire rod. 12. Put flat tire and tool bag with jack handle, lug nut wrench and spare tire rod away.
Roadside Emergencies JUMP STARTING YOUR VEHICLE WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability.
Roadside Emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure.
Roadside Emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles).
Customer Assistance CUSTOMER ASSISTANCE (U.S.A.) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer.
Customer Assistance Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer’s service facilities. personnel and equipment. We urge you to follow the above three steps in sequence therefore for most effective results. MEDIATION/ARBITRATION PROGRAM Occasionally a customer concern cannot be resolved through Mazda’s Customer Satisfaction Program. If after exhausting procedures in this manual, your concern is still not resolved, you have another option.
Customer Assistance Provincial Administrators may be reached locally as listed below: Province/Territory CAMVAP Number British Columbia & Yukon (604) 681–0312 Territories Alberta & Northwest Territories (403) 426–0650 Saskatchewan (306) 352–9259 Manitoba (204) 942–7166 Ontario (416) 596–8824 Atlantic Canada (902) 422–5413 Quebec (418) 649–1330 REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc.
Customer Assistance CUSTOMER ASSISTANCE (PUERTO RICO) Your complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Customer Assistance MAZDA IMPORTERS/DISTRIBUTORS U.S.A (Importer/Distributor) Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 TEL: 1 (800) 222–5500 (in U.S.A.) (949) 727–1990 (outside U.S.A.) (Distributor in each area) CANADA Mazda Canada, Inc. 305 Milner Avenue, Suite 400 Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P.O.
Customer Assistance AMERICAN SAMOA Polynesia Motors, Inc. P.O. Box 1120, Pago Pago, American Samoa 96799 TEL: (684) 699–1854 ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or safety system; the manufacturer’s warranty doesn’t cover this.
Customer Assistance • California Emission Control Warranty (if applicable) • Replacement Parts and Accessories Limited Warranty • Tire Warranty NOTE: Detailed warranty information is provided with your Mazda portfolio. OUTSIDE THE UNITED STATES AND CANADA Government regulations in the United States require that automobiles meet specific emission regulations and safety standards. Therefore, vehicles built for use in the United States, its territories, and Canada may differ from those sold in other countries.
Customer Assistance (Note) If you live in the U.S.A., all correspondence to Mazda Motor Corporation should be forwarded to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 Customer Assistance Center or toll free at 1 (800) 222–5500 If you live outside of the U.S.A., please contact the nearest Mazda Distributor. (See the Mazda Importers/Distributors section of this manual).
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as an approved shampoo available from your Mazda dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. • Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning PAINT CHIPS Your dealer has touch-up paint to match your vehicle’s color. Touch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish.
Cleaning • 2.0L DOHC I4 — Zetec Engine • 3.0L DOHC V6 — Duratec Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use One Step Wash and Wax Concentrate, available at your authorized Mazda dealer.
Cleaning windshield, rear window or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, tree sap, or other organic contamination. To clean these items, please follow these tips: • The windshield or rear window may be cleaned with a non-abrasive cleaner such as Ultra Clear Spray Glass Cleaner, available from your authorized Mazda dealer. • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts.
Cleaning • If grease or tar is present on the material, spot-clean the area first with Spot and Stain Remover, available at your authorized Mazda dealer. • Never saturate the seat covers with cleaning solution. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. WARNING: Do not use chemical solvents or strong detergents when cleaning the seat where the side air bag is mounted.
Maintenance and Specifications INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer. Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.
Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months x 1000 Km 12 18 24 30 36 42 48 12 24 6 36 48 60 72 84 96 108 120 132 144 54 60 66 72 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months x 1000 Km 12 18 24 30 36 42 48 12 24 6 36 48 60 72 84 96 108 120 132 144 54 60 66 72 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ENGINE I Engine valve clearance (for 2.0L engine) Engine timing belt (for 2.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) CHASSIS and BODY Brake lines, hoses and connections I I Brake fluid level I I I I I I I I I I I I Disc brakes I I I I Drum brakes I I Tire inflation pressure and tire wear I I I I I I I I I I I I Ste
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance section which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Information” to find out which parts and services are covered.
Maintenance and Specifications Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel.
Maintenance and Specifications 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1 2 9 3 8 7 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake/Clutch fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8. Engine oil dipstick 9.
Maintenance and Specifications 3.0L DOHC V6 Duratec engine 1 2 10 3 9 8 4 5 6 7 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Windshield washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. WARNING: If you operate your vehicle in temperatures below 4.5° C (40° F), use washer fluid with antifreeze protection.
Maintenance and Specifications ENGINE OIL Checking the engine oil Refer to the service maintenance section for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and Specifications • 3.0L DOHC V6 Duratec engine MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN-MAX or ADD-FULL marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range. • 2.
Maintenance and Specifications • 3.0L DOHC V6 Duratec engine • Oil levels above the MAX or FULL mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications Engine oil and filter recommendations SAE 5W-20 engine oil is recommended Look for this certification trademark. Use SAE 5W-20 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’s engine. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications RN LE TU AD RE transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance section for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications The cooling system in your vehicle is filled with either green-colored or yellow-colored Mazda Premium Engine Coolant meeting Mazda Specifications. To determine your vehicle’s coolant type (color), check your coolant reservoir. To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: • Add Mazda Premium Engine Coolant or the type of coolant originally equipped in your vehicle.
Maintenance and Specifications WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle).
Maintenance and Specifications Recycled engine coolant Not all coolant recycling processes produce coolant which meets Mazda recommend coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions WARNING: Do not overfill the fuel tank.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: WARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Extinguish all smoking materials and any open flames before fueling your vehicle.
Maintenance and Specifications WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Maintenance and Specifications Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. NOTE: Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. indicator may come on. For more information on the “Check • The Engine” indicator, refer to the Instrument Cluster chapter.
Maintenance and Specifications WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. WARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Maintenance and Specifications Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
Maintenance and Specifications • Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving.
Maintenance and Specifications If other than Mazda authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Mazda parts should be equivalent to genuine Mazda parts in performance and durability. WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Maintenance and Specifications • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.
Maintenance and Specifications BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance section for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until the level reaches MAX. Do not fill above this line. 4.
Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance section for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed.
Maintenance and Specifications The transmission fluid should be in the crosshatch zone if at normal operating temperature (66°C-77°C [150°F-170°F]). High fluid level Fluid levels above the crosshatch zone may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
Maintenance and Specifications Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Mazda specifications. Refer to the Refill capacities in this chapter.
Maintenance and Specifications WARNING: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover. 2. Release the clamps that secure the air filter housing cover. 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the air filter housing. 5.
Maintenance and Specifications These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S.
Maintenance and Specifications WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge.
Maintenance and Specifications • Four tire rotation • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Maintenance and Specifications WARNING: When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle handling may be affected which can lead to loss of vehicle control, vehicle rollover and/or personal injury.
Maintenance and Specifications Drive cautiously. If you hear the chains rub or bang against the vehicle, stop and retighten them. If this does not work, remove the cables to prevent vehicle damage. • Avoid overloading your vehicle. • Remove the tire chains when they are no longer needed. • Do not use chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from the vehicle when using snow tires and traction devices.
Maintenance and Specifications Fluid Transfer Case Engine coolant Rear axle lubricant 4 Classification SAE 75W-140 Synthetic Lubricant API service GL-5, SAE 80W-90 Mazda green-colored or yellow-colored Premium Engine Coolant API service GL-5, SAE 80W-90 Premium Rear Axle Lubricant n/a Application Capacity 4X4 (Automatic) 0.35L (12 ounces) 4X4 (Manual) 0.35L (12 ounces) 2.0L I4 Zetec engine with manual transaxle 3.0L V6 Duratec engine with automatic transaxle 4X4 5.0L (5.3 quarts) 10.0L (10.
Maintenance and Specifications For further information on your lubrication specifications, see your authorized Mazda dealer. WHEEL AND TIRE SIZES Vehicle Grade DX LX-V6/ES-V6 DX-V6 –(Puerto Rico only) Wheel 6.5JJx16 7.0JJx16 Tire Spare Wheel Spare Tire 215/70R16 17x4T 135/90R17 235/70R16 17x4T 145/90R17 ENGINE SPECIFICATIONS Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 2.0L DOHC I4 Zetec engine 121 87 octane 1-3-4-2 1.22-1.32 mm (0.048-0.
Maintenance and Specifications 1 2 3 4 5 237
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident.
Index A Axle refill capacities ........................234 ABS (see Brakes) .....................125 Accessory delay ..........................61 B Air bag supplemental restraint system ..................99, 104 and child safety seats ............101 description ........................99, 104 disposal ............................103, 107 driver air bag ..................101, 106 indicator light .................103, 107 operation .........................101, 106 passenger air bag ...........
Index Cleaning your vehicle engine compartment ..............188 instrument panel ....................190 interior .....................................190 interior trim ............................190 Mazda car care products .......191 plastic parts ............................189 washing ....................................187 waxing .....................................187 wheels ......................................188 wiper blades ............................
Index preparing to drive your vehicle .....................................128 Fuel ............................................214 calculating fuel economy .......219 cap ...........................................218 capacity ...................................234 choosing the right fuel ...........216 comparisons with EPA fuel economy estimates .................222 detergent in fuel .....................217 filling your vehicle with fuel ...........................214, 218–219 filter, specifications ....
Index K Keys positions of the ignition .........120 L Lamps bulb replacement specifications chart ..................51 cargo lamps ...............................49 daytime running light ...............48 fog lamps ...................................48 headlamps .................................48 headlamps, flash to pass ..........49 instrument panel, dimming .....49 interior lamps .....................50–51 replacing bulbs ...................51–55 Lane change indicator (see Turn signal) ..................
Index Rear window defroster ...............47 Relays ........................................156 Remote entry system illuminated entry ......................74 locking/unlocking doors ...........69 Roof rack .....................................68 S Safety belts (see Safety restraints) ..............................89–93 Safety defects, reporting ..........186 Safety restraints ....................89–94 cleaning the safety belts ..........98 extension assembly ..................95 for adults ...............
Index W Warning lights (see Lights) .......10 Washer fluid ..............................202 Water, Driving through .............147 Windows power .........................................60 rear wiper/washer .....................56 Windshield washer fluid and wipers checking and adding fluid .....202 checking and cleaning ..............57 liftgate reservoir .....................202 operation ...................................56 replacing wiper blades .............57 Wrecker towing .......................
