Table of Contents Introduction Instrument Cluster 4 14 Warning and control lights Gauges 14 19 Entertainment Systems 21 AM/FM stereo with single CD AM/FM stereo with in-dash six CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Traction control 21 25 32 32 34 34 37 39 45 45 46 49 50 51 Locks and Security 58 Keys Locks Anti-theft system 5
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving 70 70 79 95 111 123 126 127 140 146 153 158 159 Starting Brakes Transmission operation 159 163 168 Roadside Emergencies 184 Hazard flasher switch Fuses and relays Changing tires Lug Nut Torque Overheating Jump starting Wrecker towing 184 185 191
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Refill capacities Engine data 229 238 241 245 247 253 267 269 271 Accessories 276 Index 277 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from MNAO.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by a bold WARNING statement. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1,000 miles (1,600 km) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in.
Introduction Emission warranty The New Vehicle Limited Warranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Using your vehicle as an ambulance WARNING: Do not use this vehicle as an ambulance.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Powertrain Malfunction Speed Control Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX MIN 9 2006 Tribute (j14) Own
Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice.
Instrument Cluster 11 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Instrument Cluster Headlamp and turn signal control (pg. 34) Windshield wiper/washer control (pg. 45) Instrument cluster (pg. 14) Power mirror control* (pg. 50) Speed controls* (pg. 51) Instrument panel Driver air bag dimmer/dome light (pg. 95) control (pg. 36) Hood release handle (pg. 236) * if equipped 12 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Manual tilt steering column lever (pg.
Instrument Cluster Passenger airbag off indicator (pg. 99) Hazard flasher control (pg. 184) Audio system (pg. 21) Cigarette lighter* (pg. 48) Climate controls (pg. 32) Fog lamp control* Rear window defroster (pg. 35) control (pg. 32) Air conditioning control (pg. 32) Auxiliary power point (pg.
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information.
Instrument Cluster 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off.
Instrument Cluster It may take a long period of time for the system to detect an improperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and Specifications chapter.
Instrument Cluster Airbag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by an authorized Mazda dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly.
Instrument Cluster Four wheel drive indicator (if equipped): Illuminates when ignition is first turned ON to check bulb. Blinking indicator indicates system has been disabled, refer to the Driving chapter. Note: If the light remains on, have the system serviced by an authorized Mazda dealer. Anti-theft system: Flashes when the Securilock娂 Passive Anti-theft System has been activated. Refer to SecuriLock娂 passive anti-theft system in the Locks and Security chapter.
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Refer to Engine coolant in the Maintenance and Specifications chapter.
Instrument Cluster Odometer: Registers the total miles (kilometers) of the vehicle. Trip odometer: Registers the miles (kilometers) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems AUDIO SYSTEMS AM/FM Stereo Single CD audio system — Satellite ready capability 1. CD: To begin CD play, insert a CD into the slot, label side up. The system will load the CD and begin play after a short pause. The track number will illuminate in the display. 2. MD/TAPE: This control does not function on the base audio system. It will function with a tape or mini disc (MD) upgrade. 3. CLOCK: Press and release CLOCK to alternate between the time and the audio display.
Entertainment Systems Press and hold CLOCK for approximately two seconds until a beep sound is heard. The clock’s current time will flash. Press SCAN adjust the hours. Press AUTO-M to adjust the minutes. Press CLOCK again to start the clock. NOTE: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode.
Entertainment Systems Press the FM/AM control to select a frequency. Press and momentarily hold the AUTO-M (Auto memory) control. The system will beep. Press the AUTO-M (Auto memory) control to select from the stored stations. One stored station will be selected and played each time the control is pressed. The frequency and channel number will be displayed. NOTE: If no stations can be tuned after scanning operations, A will appear in the display.
Entertainment Systems 11. DISC : Press to skip forward to the beginning of the next CD. : Press to skip back 12. DISC to the beginning of the previous CD. 13. Volume/ON/OFF: Press to turn the system on/off. Turn to adjust the volume. 14. Memory presets: Your audio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Select a frequency with the AM/FM. 15.
Entertainment Systems 16. FM/AM: Press to enter radio mode and select a frequency from FM1, FM2 or AM. 17. SAT: Your radio comes equipped with Satellite ready capability. This enables you to view the song titles, artist, and further information. The kit to enable Satellite reception is available through your dealer. Detailed Satellite instructions are included with the dealer installed kit. AM/FM Stereo Six CD audio system — Satellite ready capability (if equipped) 1.
Entertainment Systems 2. MD/TAPE: This control does not function on this audio system. It will function with a cassette or mini disc (MD) upgrade. 3. CLOCK: Press and release CLOCK to alternate between the time and the audio display. The clock can be set at any time when the ignition switch is in the ACC or ON position. Press and hold CLOCK for approximately two seconds until a beep sound is heard. The clock’s current time will flash. Press SCAN adjust the hours. Press AUTO-M to adjust the minutes.
Entertainment Systems 5. SCAN/DISP/ESN/AUTO-M SCAN: Press in radio or CD mode DISP/ESN for a brief sampling of all listenable stations or of each CD track. Press again to disable scan mode. If the unit is left in scan mode, normal play will resume where scan was selected. DISP/ESN: Your radio comes equipped with Satellite ready capability. This enables you to view the song titles, artist, and further information. The kit to enable Satellite reception is available through your dealer.
Entertainment Systems 7. Fast forward: In CD mode, press and hold to advance through a track at a high speed. 8. Rewind: In CD mode, press and hold to reverse through a track at a high speed. 9. PROG/RDM: Press during CD play for a random selection of songs. Press again to disengage random play. RDM will illuminate in the display. 10. RPT: Press during CD play to listen to a selection repeatedly. RPT will illuminate in the display and the current selection will be repeated.
Entertainment Systems 14. Memory presets: Your audio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and 12 FM stations (six in FM1 and six in FM2). Select a frequency with the AM/FM. 15. SEEK/TRACK/APC: SEEK works in radio mode and allows you to advance to all listenable radio stations up or the radio frequency. down Note: If you continue to press and hold the control, the frequency will continue changing without stopping.
Entertainment Systems GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.
Entertainment Systems CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only.
Climate Controls MANUAL HEATING AND AIR 1 5 CONDITIONING SYSTEM 1. A/C: Press to activate A/C. The indicator light will illuminate to indicate A/C is functioning. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following 4 3 2 for a brief description on each control. : Distributes air through the instrument panel vents.
Climate Controls WARNING: Under some weather conditions, use of the recirculated air mode may lead to glass misting or fogging. Switch the air conditioner on and select the fresh air mode. Heated air can assist windscreen demisting. Operating tips • To reduce fog build up on the windshield during humid weather, place position.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Battery saver Your vehicle is equipped with a battery saver feature which, if you leave the headlamps on, automatically turns off the headlamps after 30 seconds when the ignition is in the OFF position. High beams After turning the headlamps on, push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
Lights Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged. WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions.
Lights INSTRUMENT PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. VERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meter) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2.
Lights 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted. 5. Locate the vertical adjuster on the headlamp, then use a 7 mm hex socket or T20 Torx driver to turn the adjuster either counterclockwise (to adjust down) or clockwise (to adjust up) aligning the upper edge of the light pattern up to the horizontal line.
Lights INTERIOR LAMPS Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. When the control is in the OFF position, it will not illuminate when you open the doors. Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats.
Lights For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate the lamps. Push the button again to turn off the lamps. The map lamps will illuminate whenever a door is opened. After the door is shut, the lamps will remain illuminated for 25 seconds. BULB REPLACEMENT Replacing exterior bulbs Check the operation of all the bulbs frequently.
Lights Function Number of bulbs 2 2 2 2 2 2 2 2 1 5 Park/turn lamps (front) Headlamps Rear stop/tail lamps Rear turn lamps Rear license plate lamps Backup lamp Side repeater lamp Fog lamp (if equipped) Cargo lamp Center high-mount stop lamp Interior overhead lamp Map lamps All replacement bulbs are clear To replace all instrument panel dealer. Trade number 3157 AK (amber) 9003 (HB2) W21/5W WY21W (amber) W5W W21W WY5W (amber) H1 211-2 W5W 1 912 (906) 2 168 (T10) in color except where noted.
Lights 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the rubber boot from the lamp assembly by pulling on one of the tabs. 5. Squeeze the retainer spring together releasing it from bulb hooks and rotate it away from the bulb.
Lights 6. Without turning, carefully pull bulb out of headlamp assembly. Note: The bulb’s metal base gets very hot during headlamp operation. Be sure the bulb base is cool before handling. If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 7. Insert the glass end of the new bulb into the headlamp assembly.
Lights Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly by pulling it rearward. 4. Twist the bulb socket counterclockwise and remove from lamp assembly. 5. Pull the bulb straight out of the socket and push in the new bulb. 6.
Lights Replacing high-mount brake lamp bulbs To remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb. To complete installation, follow the removal procedure in reverse order.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF. Mist function: To activate mist, push control up from the OFF position and release to get one wipe. Windshield washer: To activate the windshield washer, pull control toward you.
Driver Controls Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward position. to the For normal speed rear wiper operation, rotate control upward to ON. To activate the rear washer, rotate position and the control to the release. MANUAL TILT STEERING COLUMN To adjust the steering wheel: 1. Pull down and hold the steering wheel release control. 2. Move the steering wheel up or down until you find the desired location. 3.
Driver Controls WARNING: Adjusting the steering wheel while the vehicle is moving is dangerous. Moving it can very easily cause the driver to abruptly turn to the left or right. This can lead to loss of control or an accident. Never adjust the steering wheel while the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.
Driver Controls 1. 2. 3. 4. Power point Cupholders Utility compartment Ash cup (if equipped) WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. AUXILIARY POWER POINT (12VDC) WARNING: Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug.
Driver Controls POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. The ignition must be in the ON position to adjust the power windows. Press and hold the bottom part of the rocker switch to open the window.
Driver Controls Note: The passenger window switches will not illuminate when the window control is in the LOCKED position. Press the left side to restore the window controls. Accessory delay With accessory delay, power windows and moonroof operate for up to ten minutes after the ignition switch is turned from the ACC or ON to the OFF position, the key is not in the ignition or until either front door is opened.
Driver Controls Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Driver Controls 3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. RSM SET ACC CST Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your cruise control/speed control will disengage.
Driver Controls Increasing speed while using cruise control/speed control There are two ways to set a higher speed: RSM • Press and hold the SET ACC control until you get to the SET desired speed, then release the ACC control. You can also use the SET ACCEL control to operate the Tap-Up function. Press and CST release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h). • Use the accelerator pedal to get to the desired speed.
Driver Controls Turning off cruise control/speed control There are two ways to turn off the cruise control/speed control: ON • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed. • Press the cruise control/speed OFF control OFF control. Note: When you turn off the cruise control/speed control or the ignition, your cruise control/speed control set speed memory is erased.
Driver Controls WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening. LIFTGATE To open the rear window, pull the right side of the liftgate handle. To open the liftgate, pull the left side of the liftgate handle.
Driver Controls CARGO SHADE (IF EQUIPPED) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. To install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels. To operate the shade: 1. Grasp the handle at the rear edge of the shade and pull rearward. 2. Secure both ends of the support rod into the retention slots located on the rear quarter trim panels.
Driver Controls LUGGAGE RACK The maximum load for the roof rack is 100 lbs (45 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars (if equipped) as possible. Always use the adjustable tie down loops to secure the load. To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3.
Locks and Security KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section later in this chapter for more information.
Locks and Security 7. Turn the ignition from the 3 (ON) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock the driver’s door. Note: The interior lamps will illuminate if the control on the overhead lamp is in the DOOR position and the perimeter alarm system (if equipped) will deactivate.
Locks and Security CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Rotate lock control in the direction of arrow to engage the lock.
Locks and Security • weak or dead transmitter battery. The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote locking and unlocking features will operate independent of the ignition position; however, the panic feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACCESSORY) position.
Locks and Security Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash once and the perimeter alarm (if equipped) will start the arming process. For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. and release again within three seconds to confirm that all 2. Press the doors and liftgate are closed and locked.
Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together.
Locks and Security To reprogram the remote entry transmitters: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Ensure the vehicle is electronically unlocked. Put the key in the ignition. Turn the key from the 1 (LOCK) position to 3 (ON). Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (ON) position. The doors will lock, then unlock, to confirm that the programming mode has been activated.
Locks and Security Illuminated exit • The interior lights will illuminate when the key is removed from the ignition. The lamps automatically turn off after 25 seconds. The dome and cargo lamp controls must not be set to the OFF position for the illuminated exit system to operate. SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system.
Locks and Security If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized Mazda authorized dealer for service. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer.
Locks and Security Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ignition from the 1 (LOCK) position to the 3 (ON) position. Keep the ignition in the 3 (ON) position for at least three seconds, but no more than 10 seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition. 4.
Locks and Security PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting. Arming the system When armed, this system will respond if unauthorized entry is attempted.
Locks and Security Disarming the system You can disarm the system by any of the following actions: control on your remote entry • Unlock the doors by pressing the transmitter. • Unlock the doors with a key. Turn the key full travel (toward the front of the vehicle) to ensure the alarm disarms. • Turning the key in the ignition to the 3 (ON) or 4 (START) position.
Seating and Safety Restraints SEATING Adjustable head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Push side control and push down on head restraint to lower it.
Seating and Safety Restraints WARNING: Not securing luggage or cargo while driving is dangerous as it could move or be crushed during sudden braking or a collision and cause injury. Make sure luggage and cargo are secured before driving. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across the chest.
Seating and Safety Restraints Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’s seatback. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. You could move out of position to control the vehicle. Then a serious accident could occur.
Seating and Safety Restraints WARNING: To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details.
Seating and Safety Restraints Heated seats (if equipped) To operate the heated seats: • Push the control located on the seat to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position. REAR SEATS Head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Seating and Safety Restraints Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat.
Seating and Safety Restraints 4. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button. This will assure that seatbelt does not get caught by staying out of the seat back folding path. 5. To release seatback, pull the seatback release lever (on top of seat) toward the front seat. NOTE: When the seatback release lever is pulled, slowly lower seatback to the flat position.
Seating and Safety Restraints 6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and the RED seat unlatched indicator on release paddle is not visible.
Seating and Safety Restraints WARNING: Make sure safety belt buckle heads are through elastic holders on seat backs. Safety belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
Seating and Safety Restraints To install the rear cushion 1. Insert rod ends into floor mounting points and push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System姟 The Personal Safety System娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
Seating and Safety Restraints How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM).
Seating and Safety Restraints Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag.
Seating and Safety Restraints safety belt pretensioner activation depending upon safety belt usage. Refer to Safety restraints section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during a frontal or near-frontal collision.
Seating and Safety Restraints Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across the chest. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Seating and Safety Restraints WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying airbag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side airbag (if equipped) in a moderate collision. Whenever possible, always secure a child, 12 years or younger, in the rear seat, with an appropriate child restraint system for the child’s age and size.
Seating and Safety Restraints WARNING: All safety belts should be checked for proper function. Additionally, if the front airbags have deployed, the front pretensioners have also deployed and both front restraints must be replaced.
Seating and Safety Restraints How to use the automatic locking mode for use with child safety seats • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints WARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which doesn’t have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.
Seating and Safety Restraints When the side-curtain airbags (if equipped) and/or the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled.
Seating and Safety Restraints Safety belt extension assembly If the safety belt assembly is too short for you, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly. Safety belt extension assemblies can be obtained from your authorized Mazda dealership. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints WARNING: Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...
Seating and Safety Restraints Both the driver’s and passenger’s safety belt usages are monitored and either may activate the BeltMinder威 feature. The warnings are the same for the driver and the front passenger. If the BeltMinder威 warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the BeltMinder威 feature. If...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... ⬙Crashes are rare events⬙ ⬙I’m not going far⬙ ⬙Belts are uncomfortable⬙ ⬙I was in a hurry⬙ ⬙Seat belts don’t work⬙ ⬙Traffic is light⬙ ⬙Belts wrinkle my clothes⬙ ⬙The people I’m with don’t wear belts⬙ Consider... 36,700 crashes occur every day. The more we drive, the more we are exposed to ⬙rare⬙ events, even for good drivers.
Seating and Safety Restraints Reasons given... ⬙I have an airbag⬙ ⬙I’d rather be thrown clear⬙ Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T ⬙PICK OUR CRASH⬙. WARNING: Always wear the safety belt.
Seating and Safety Restraints • The driver and front passenger safety belts are unbuckled WARNING: While the design allows you to deactivate your BeltMinder威, this system is designed to improve your chances of being seat belted and surviving an accident, and we recommend you leave the BeltMinder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the BeltMinder威 feature while driving the vehicle. 1.
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module.
Seating and Safety Restraints WARNING: The driver should always hold onto only the rim of the steering wheel. Never place your arm over the airbag module or anywhere inside the rim as a deploying airbag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly (one or two notches) from the upright position.
Seating and Safety Restraints Children and airbags For additional important safety information, read all information on safety restraints in this guide. WARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions rather than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. WARNING: Airbags can kill or injure a child in a child seat.
Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints • • • • a readiness light and tone diagnostic module and the electrical wiring which connects the components. Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system. later in this chapter.
Seating and Safety Restraints For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located in the center stack of the instrument panel just below the radio.
Seating and Safety Restraints • Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag.
Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below. Objects Pass Airbag Off Indicator Lamp Unlit Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check Passenger Airbag Disable Indicator for proper airbag Status. Failure to follow these instructions may interfere with the front passenger seat sensing system.
Seating and Safety Restraints Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Manual. WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter.
Seating and Safety Restraints WARNING: Do not use accessory seat covers or non-Mazda leather seat upgrade kits. The use of accessory seat covers and kits may prevent the deployment of the side airbags and increase the risk of injury in an accident. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. WARNING: Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag.
Seating and Safety Restraints Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. If the front passenger sensing system detects an empty seat, the front passenger seat-mounted side airbag will be deactivated.
Seating and Safety Restraints The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either flash or stay lit.
Seating and Safety Restraints WARNING: Do not attempt to service, repair, or modify the side-curtain airbags (if equipped), fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing side-curtain airbags. See your authorized Mazda dealer. WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and side-curtain airbags (if equipped) are provided.
Seating and Safety Restraints • Two crash sensors mounted at lower B-Pillar (one on each side). • Two crash sensors located at the c-pillar behind the rear doors (one on each side). • Rollover sensor in the restraints control module (RCM). The side-curtain airbags (if equipped), in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event.
Seating and Safety Restraints WARNING: Several side-curtain airbag (if equipped) components get hot after inflation. Do not touch them after inflation. WARNING: If the side-curtain airbags (if equipped) have deployed, the side-curtain airbags will not function again unless replaced. The side-curtain airbags (including the A, B and C pillar trim) must be inspected and serviced by a authorized dealer in accordance with the vehicle workshop manual.
Seating and Safety Restraints Disposal of airbags and airbag equipped vehicles For disposal of safety belt pretensioners, airbags, or airbag equipped vehicles, see your authorized Mazda dealership. Airbags MUST BE disposed of by qualified personnel. WARNING: Disposing of an airbag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda dealer how to safely dispose of an airbag or how to scrap an airbag equipped vehicle.
Seating and Safety Restraints If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. WARNING: Do not leave children, unreliable adults, or pets unattended in your vehicle. WARNING: Placing a child, 12 years or younger, in the front seat is dangerous.
Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? WARNING: Booster seats must be installed only in seating positions equipped with a combination lap/
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb. Children and booster seats vary widely in size and shape.
Seating and Safety Restraints WARNING: Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision.
Seating and Safety Restraints • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. 4. Clip the tether strap to the anchor as shown.
Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use safety belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor.
Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and Specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle.
Tires, Wheels and Loading • Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Tires, Wheels and Loading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Tires, Wheels and Loading Glossary of tire terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire.
Tires, Wheels and Loading Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Mazda.
Tires, Wheels and Loading When weather temperature changes occur, tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure.
Tires, Wheels and Loading TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear.
Tires, Wheels and Loading WARNING: Age Tires degrade over time, even when they are not being used. It is recommended that tires generally be replaced after 6 years of normal service. Heat caused by hot climates or frequent high loading conditions can accelerate the aging process. You should replace the spare tire when you replace the other road tires due to the aging of the spare tire. U.S. DOT Tire Identification Number (TIN) Both U.S.
Tires, Wheels and Loading It is recommended that the two front tires or two rear tires generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The installation of replacement tires with steel cord body plies in the tire sidewall may cause malfunction of the Tire Pressure Monitoring System (TPMS), and is not recommended (cord material information is molded on the tire sidewall).
Tires, Wheels and Loading Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road.
Tires, Wheels and Loading • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (AWD) vehicles (front tires at top of diagram) 134 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Tires, Wheels and Loading Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading 3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your Owner’s Guide. If not, contact a local tire dealer.
Tires, Wheels and Loading 8. U.S. DOT Tire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001.
Tires, Wheels and Loading 13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading When your temporary spare tire is installed (if equipped) When one of your road tires needs to be replaced with the temporary spare (T-type spare/Mini spare or Dissimilar spare), the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle. During this time, the low tire warning light can periodically return or stay on, depending on the state of the damaged road wheel/tire.
Tires, Wheels and Loading Low Tire Pressure Warning Light Solid Warning Light Possible cause Customer Action Required Tire(s) under-inflated 1. Check your tire pressure to ensure they are properly inflated; refer to Inflating your tires in this chapter. Mazda Motor Corporation recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge for increased accuracy. 2.
Tires, Wheels and Loading Low Tire Pressure Warning Light Flashing Warning Light (flashes for a short time either at start-up or while driving) Possible cause Customer Action Required Spare tire in use Your temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to Changing tires with TPMS in this section.
Tires, Wheels and Loading How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. The pressure in each tire is dependent upon several factors, one of them being the contained air temperature (temperature of the air inside the tire). As the contained air temperature increases, the tire pressure also increases.
Tires, Wheels and Loading Follow these guidelines when using snow tires and traction devices: • SAE class “S” cables should ONLY be used on the front axle for P235/70R16 tires. • Install cables or chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously. If you hear the cables or chains rub or bang against the vehicle, stop and retighten them. If this does not work, remove the cables or chains to prevent vehicle damage. • Avoid overloading your vehicle.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR. MFD. BY FORD MOTOR CO. IN U.S.A.
Tires, Wheels and Loading 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer, multiply 5,000 by 0.10 and 0.
Tires, Wheels and Loading 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
Tires, Wheels and Loading Special loading instructions for owners of pickup trucks and utility-type vehicles WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide. WARNING: Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Tires, Wheels and Loading Do not exceed the maximum loads listed on the Safety Compliance Certification Label. For load specification terms found on the label, refer to Vehicle loading in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. 4x2 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum Trailer Weight Maximum GCWR - lb. Range - lb. frontal area of (kg) (kg) trailer - ft2 (m2) 2.3L w/manual 4860 (2204) 1500 (680) 24 (2.
Tires, Wheels and Loading 4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum Trailer Weight Maximum GCWR - lb. Range - lb. frontal area of (kg) (kg) trailer - ft2 (m2) 2.3L w/manual 5040 (2286) 1500 (680) 24 (2.2) transmission 2.3L 5100 (2313) 1500 (680) 24 (2.2) w/automatic transmission 3.0L 7240 (3284) 3500 (1588) 30 (2.8) w/automatic transmission Notes: For high altitude operation, reduce GCW by 2% per 1,000 ft. (300 meters) elevation.
Tires, Wheels and Loading Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized Mazda dealer. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts. • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling.
Tires, Wheels and Loading • Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’s wheels. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper. • Do not allow waves to break higher than 6 inches (15 cm) above the bottom edge of the rear bumper.
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. Preparing to start your vehicle Engine starting is controlled by the powertrain control system.
Driving WARNING: If you smell exhaust fumes inside your vehicle, have your authorized dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your authorized dealer. Before starting the vehicle: 1.
Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1.
Driving Note: If the engine does not start within five seconds on the first try, turn the key to 1 (LOCK), wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up.
Driving Note: Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. USING THE ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10°F (-23°C) or below.
Driving Four-wheel anti-lock brake system (ABS) Since your vehicle is equipped with an Anti-lock Braking System (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system.
Driving ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal ! braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving To release the parking brake, the brake handle may need to be pulled up slightly (1) to release pressure before pushing in the button (2). Push the button on the end of the parking brake handle and push the handle down as far as possible. Driving with the parking brake applied will cause the brakes to wear out quickly and reduce fuel economy.
Driving PREPARING TO DRIVE YOUR VEHICLE Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances. These special design features, such as larger tires and increased ground clearance, give the vehicle a higher center of gravity than a passenger car. WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Driving WARNING: Do not drive your vehicle until you verify that the brakelamps are working. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer as soon as possible.
Driving This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected.
Driving D (Overdrive) The normal driving position for the best fuel economy. Transaxle operates in gears one through four. D (Overdrive) can be deactivated by pressing the O/D OFF switch on the side of the gearshift lever. This will illuminate the O/D OFF light and deactivate the overdrive. Drive (O/D OFF switch pressed) Drive is activated when the O/D OFF switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF light is illuminated. • Provides engine braking.
Driving 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. WARNING: When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
Driving When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in the neutral position. 1 3 5 2 4 R 2. Hold down the brake pedal. 3. Depress the clutch pedal to the floor. 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds. 6. Release the brake pedal, then slowly release the clutch pedal while pressing down slowly on the accelerator pedal.
Driving Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 1-2 10 mph (16 km/h) 2-3 20 mph (32 km/h) 3-4 32 mph (52 km/h) 4-5 37 mph (60 km/h) Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle.
Driving Parking your vehicle 1. Apply the brake and shift into the neutral position. 1 3 5 2 4 R 1 3 5 2 4 R 2. Set the parking brake. 3. Depress the clutch, then shift into 1 (First).
Driving 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter.
Driving • Illuminates when 4WD system requires service. Please bring your vehicle to your local authorized dealer for service. Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles Truck and utility vehicles can differ from some other vehicles.
Driving • It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or rollover. Remember, your safety and the safety of others should be your primary concern. WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity.
Driving WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control, not more.
Driving Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Mud and water NOTE: • If you must drive through high water, drive slowly. Traction or brake capability may be limited.
Driving “Tread Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Mazda Motor Corporation joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.
Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t turn and if they aren’t turning, you won’t be able to steer. The front wheels have to be turning in order to steer the vehicle.
Driving • 4WD vehicles should be driven with traction devices as referred to in Using snow tires and traction devices in the Tires, Wheels and Loading chapter. Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability.
Roadside Emergencies HAZARD FLASHER CONTROL The hazard flasher is located on the instrument panel by the radio. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. Note: With extended use, the flasher may run down your battery.
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. 15 Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside Emergencies Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 Fuse Amp Rating 15A* 5A* 15A* 10A* 2A* 6 15A* 7 10A* 8 9 10 11 12 13 14 15 16 17 18 19 20 21 — 30A** 15A* 15A* — — — 30A** 15A* 15A* 10A* — 15A* 10A* Passenger Compartment Fuse Panel Description Trailer tow park lamps Radio (illumination) Front and rear park lamps Ignition switch Powertrain Control Module (PCM relay), Fuel pump relay, Main fan relay, High/Low speed fan relay 2, PATS module Center High-Mounted Stop Lam
Roadside Emergencies Fuse/Relay Location 22 23 24 25 Fuse Amp Rating 10A* 5A* 20A* 20A* 26 5A* 27 5A* 28 29 30 31 32 33 10A* — — — 10A* 15A* 34 5A* 35 5A* * Mini fuse ** Cartridge fuse Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Roadside Emergencies WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 11 12 13 14 15 Fuse Amp Rating 10A* 20A* 20A* 15A* 30A* 16 17 18 19 25A* 50A** 40A** 40A** 20 21 60A** 40A** 22 23 24 25 R2 R3 R4 R5 R6 R7 R8 R9 R10 D1 D2 * Mini fuse 40A** (I4) 50A** (V6) 40A** 40A** (I4) 50A** (V6) — — — — — — — — — — — — ** Cartridge fuse 190 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description PCM Power point Fog lamps A/C clutch, A/C relay Anti-lock Brake System (ABS) solenoid I/P fuse panel (RUN
Roadside Emergencies CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that is different in one or more of the following: type, brand, size, speed rating and tread design. If this is the case, this dissimilar spare tire is still rated for your vehicle loads (GAWR and GVWR).
Roadside Emergencies 2.
Roadside Emergencies • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare t
Roadside Emergencies WARNING: Changing a tire is dangerous if not done properly. If the vehicle slips off the jack, you or someone else could be seriously injured. Be sure to follow the directions for changing a tire, and never get under a vehicle that is supported only by a jack. 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine off. 3.
Roadside Emergencies Unbuckle the strap and remove the jack and tools by pulling the right side up first. Remove the tools from the jack in order to remove the spare tire from under the vehicle. Note: For some non-cargo management system vehicles, the jack and tools are located in the right rear of the cargo area behind an access panel. Cargo management system (if equipped):The jack and tools are located in the right rear of the cargo area behind an access panel.
Roadside Emergencies To remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first. Remove the lug wrench from the jack in order to remove the spare tire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through the access hole in the rear bumper. 2.
Roadside Emergencies If equipped with a tether, perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether. 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached Velcro strap (2) to tie the tether end to the winch actuator shaft (if equipped).
Roadside Emergencies Changing the flat tire 8. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Roadside Emergencies • Rear 9. Lower the jack from its stored height to fit under the jacking notches. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Never use the differentials as a jacking point. WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Roadside Emergencies 11. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 12. Lower the wheel by turning the jack handle counterclockwise. 13. Remove the jack and fully 1 tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in 3 4 this chapter for the proper lug nut torque specification. 5 2 14.
Roadside Emergencies • guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close and tighten the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive. Non-cargo management system (if equipped): • Reclip the tools onto the jack making sure that the tools are fully contained by the clips as shown.
Roadside Emergencies 1. Place tire on end with valve stem facing rearward, away from vehicle. 2. Place tether into bolt holes in wheel and attach lug nut using lug wrench. 3. Lay the tire on the ground with the valve stem facing down. If your vehicle is equipped with aluminum wheels, remove the wheel center cap. 4. Slide the wheel partially under the vehicle and install the retainer through the center of the wheel. 5.
Roadside Emergencies WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N•m M12 x 1.5 100 135 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Mazda recommended replacement fasteners.
Roadside Emergencies • If steam is coming from the engine compartment: do not go near the front of the vehicle. Stop the engine, then turn the ignition switch to the ON position without starting the engine. The radiator cooling fans will start to cool the engine. • If neither coolant nor steam is escaping: open the hood and idle the engine until it cools. If this does not lower the temperature, stop the engine and let it cool. 5. Check the coolant level.
Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. • Use only a 12–volt supply to start your vehicle.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure.
Roadside Emergencies On 4WD vehicles, it is required that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. If the vehicle is towed by other means or incorrectly, vehicle damage may occur.
Customer Assistance CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance 5. Your authorized dealer’s name and location 6. Your question(s) If you live outside the U.S.A., please contact your nearest Mazda Distributor. CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance 7. The nature of your problem and/or cause of dissatisfaction. The Department, in cooperation with the local Mazda Service Representative, will review the case to determine if everything possible has been done to ensure your satisfaction. Please recognize that the resolution of service problems in most cases requires the use of your authorized dealer’s service facilities, personnel and equipment.
Customer Assistance Regional Offices Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc. Central Region 55 Vogell Road Richmond Hill, Ontario. L4B 3K5 1 (800) 263–4680 Mazda Canada Inc.
Customer Assistance STEP 2 If, after following STEP 1, you feel the need for further assistance, please contact your area’s Mazda representative (Indicated on the next page). Please help us by providing the following information: 1. Your name, address, and telephone number 2. Year and model of vehicle 3. Vehicle Identification Number (17 digits, noted on your registration or title or located on the upper driver’s side corner of the dash) 4. Purchase date and current mileage 5.
Customer Assistance 1. Two or more repair attempts are made on the same nonconformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).
Customer Assistance SAIPAN Pacific International Marianas, Inc. (d.b.a. Midway Motors) P.O. Box 887 Saipan, MP 96950 TEL: (670) 234–7524 Triple J Saipan, Inc. (d.b.a. Triple J Motors) Beach Road Chalan LauLau Saipan, MP 96950 TEL: (670) 235–4868 AMERICAN SAMOA Polynesia Motors, Inc. P.O.
Customer Assistance However, in the event that you are moving to Canada permanently, Mazda vehicles built for use in the United States could be eligible for exportation to Canada with specific vehicle modifications to comply with the Canadian Motor Vehicle Safety requirements. Special Note: The above is applicable for permanent import/export situations and not related to travelers on vacation.
Customer Assistance ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or safety system; the manufacturer’s warranty doesn’t cover this. Before you install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
Customer Assistance SERVICE PUBLICATIONS Factory-authorized Mazda service publications are available for owners who wish to do some of their own maintenance and repair. When requesting any of our publications through an Authorized Mazda Dealer, refer to the chart below. If they don’t have what you need in stock, they can order it for you.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: NHTSA 400 Seventh Street, SW Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov. (Note) If you live in the U.S.A., all correspondence to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922 P.O.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. • Always use a clean sponge or car wash mitt with plenty of water for best results.
Cleaning PAINT CHIPS Your dealer has touch-up paint to match your vehicle’s color. Touch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish.
Cleaning • 2.3L DOHC I4 Engine • 3.0L DOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use cool or lukewarm water with a neutral pH shampoo.
Cleaning • If tar or grease spots are present, use Extra Strength Tar and Road Oil Remover (0000–77–410E-01), available at your authorized Mazda dealer. WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause.
Cleaning INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, dry cloth; you may also use Mazda Deluxe Leather and Vinyl Cleaner (0000–77–430E-15). • Do not use household or glass cleaners, as these may damage the finish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags (if equipped): • Remove dust and loose dirt with a vacuum cleaner.
Cleaning LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • To clean, use a soft cloth with Deluxe Leather and Vinyl Cleaner (0000–77–430E-15), available at your authorized Mazda dealer. Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Deluxe Leather Care Kit (0000–77–609E-03), available at your authorized Mazda dealer.
Maintenance and Specifications INTRODUCTION Be extremely careful to prevent injury to yourself and others or damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an authorized Mazda Dealer. Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.
Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.5) (90) ENGINE Engine valve clearance (for 2.
Maintenance and Specifications Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.
Maintenance and Specifications SCHEDULE 2 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ENGINE Engine valve clearance
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) Engine coolant (yellow) Engine coolant level ELECTRICAL SYSTEM Function of all lights CHASSIS and BODY Brake lines, hoses and connections Brake fluid level Disc brakes Drum brakes Tire (rotation), check wheel lug nut torque *4 Tire inflation pressure and ti
Maintenance and Specifications However, Mazda recommends that all maintenance services be performed at the recommended time or miles (kilometers) period to ensure long-term reliability. Refer to Fuel filter in the Maintenance and Specifications chapter for fuel filter replacement requirements. *2 If the vehicle is operated under any of the following conditions, change the spark plugs every 60,000 miles (96,000 km) or shorter. a) Repeated short-distance driving.
Maintenance and Specifications Retightening lug nuts • Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). • Refer to Wheel Lug Nut Torque Specification in the Tires, Wheels and Loading chapter for the proper lug nut torque specification. SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location.
Maintenance and Specifications Working with the engine off • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First). 2. Turn off the engine and remove the key. 3. Block the wheels. Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels.
Maintenance and Specifications 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil filler cap 9. Engine oil dipstick 10.
Maintenance and Specifications 3.0L DOHC V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. WARNING: If you operate your vehicle in temperatures below 40° F (4.5°C), use washer fluid with antifreeze protection.
Maintenance and Specifications Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm.
Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark or the lower hole, engine oil must be added to raise the level within the normal operating range.
Maintenance and Specifications • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above the MAX mark or upper hole may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
Maintenance and Specifications 3. Recheck the engine oil level. Make sure the oil level is not above the MAX or FULL mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.
Maintenance and Specifications Mazda production and replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Mazda material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Genuine Mazda oil filter (or another brand meeting Mazda specifications) for your engine application.
Maintenance and Specifications WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Maintenance and Specifications RN TU LE AD RE NOTE: • The vehicle may need to be driven to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly.
Maintenance and Specifications Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • freeze protection down to -34°F (-36°C). • boiling protection up to 265°F (129°C). • protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant gauge.
Maintenance and Specifications WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance and Specifications water to the “FULL COLD” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap.
Maintenance and Specifications Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage). Recycled engine coolant Not all coolant recycling processes produce coolant which meets Mazda recommended coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Maintenance and Specifications • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
Maintenance and Specifications operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to an authorized dealer. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low.
Maintenance and Specifications WARNING: If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. WARNING: Automotive fuels can cause serious injury or death if misused or mishandled. WARNING: Gasoline may contain benzene, which is a cancer-causing agent.
Maintenance and Specifications • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction.
Maintenance and Specifications Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/4 turn on/off feature. When fueling your vehicle: 1. Turn the engine/ignition switch to the off position. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. To install the cap, align the lugs on the cap with the threads on the filler pipe. 4. Turn the filler cap clockwise until it clicks at least once.
Maintenance and Specifications Canada, premium grade fuel generally contains more metallic additives than regular grade fuel. We recommend using regular grade fuel. In Canada, many fuels contain metallic additives, but fuels free of such additives may be available; check with your local fuel dealer. • Do not use fuel containing methanol. It can damage critical fuel system components. • Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty.
Maintenance and Specifications Cleaner air Mazda endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • The indicator may come on.
Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand.
Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually.
Maintenance and Specifications • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Maintenance and Specifications WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
Maintenance and Specifications driving cycles without these or any other temporary malfunctions present, the indicator should turn off—A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. If the indicator remains on, have your vehicle serviced at the first available opportunity.
Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. MA X MIN 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and Specifications Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2.
Maintenance and Specifications High fluid level Fluid levels above the crosshatch zone may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Maintenance and Specifications Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Mazda specifications. Refer to the Refill capacities in this chapter.
Maintenance and Specifications 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the air filter housing. 5. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid Classification High Performance DOT 3 Motor Vehicle Brake Fluid Application Capacity All Fill to line on reservoir Engine oil (including filter change) SAE 5W-20 Fuel tank N/A All Power steering fluid MERCON威 All 3.0L V6 engine API service GL-4, SAE 75W-90 Transmission fluid1 MERCON威 ATF Transfer Case 2.
Maintenance and Specifications Fluid Engine coolant4 Rear axle lubricant Windshield washer fluid Classification Application 2.3L I4 engine with manual transaxle Mazda 2.3L I4 engine yellow-colored with automatic Premium Engine transaxle Coolant 3.0L V6 engine with automatic transaxle API service GL-5, SAE 80W-90 4WD Premium Rear Axle Lubricant N/A All Capacity 5.3 quarts (5.0L) 6.3 quarts (6.0L) 10.6 quarts (10.0L ) 2.96 pints (1.4L)5 4.8 quarts (4.
Maintenance and Specifications ENGINE SPECIFICATIONS Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 2.3L I4 engine 140 87 octane 1-3-4-2 Coil on plug 0.049–0.053 inch (1.25–1.35mm) 9.7:1 3.0L DOHC V6 engine 183 87 octane 1-4-2-5-3-6 Coil on plug 0.052–0.056 inch (1.32–1.42mm) 10.
Maintenance and Specifications 1 2 3 272 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus)
Maintenance and Specifications 4 5 IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. FOR MAZDA MOTOR CORPORATION Administration Regulations require DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG FRONT GAWR: XXXXL REAR GAWR: XXXXLB that a Safety Compliance XXXXKG WITH XXXXKG WITH Certification Label be affixed to a XXXX/XXXXXXX TIRES XXXX/XXXXXXX TIRES XXXX.XX RIMS XXXX.
Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number. XXXXXXXXXXXXXXXXX The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake type and Gross Vehicle Weight Rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5.
Maintenance and Specifications TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a MFD. BY FORD MOTOR CO. IN U.S.A. FOR MAZDA MOTOR CORPORATION transmission/transaxle code on the DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG FRONT GAWR: XXXXL REAR GAWR: XXXXLB Safety Compliance Certification XXXXKG WITH XXXXKG WITH Label . The following table tells you XXXX/XXXXXXX TIRES XXXX/XXXXXXX TIRES XXXX.XX RIMS XXXX.XX RIMS which transmission or transaxle AT XXX kPa/XX PSI COLD AT XXX kPa/XX PSI COLD each code represents.
Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident.
Index A ABS (see Brakes) .....................164 Accessory delay ..........................50 Air cleaner filter ...............267, 269 Air conditioning manual heating and air conditioning system .................32 Airbag supplemental restraint system ..........................95, 104, 107 and child safety seats ..............97 description ................95, 104, 107 disposal ....................................111 driver airbag ..............97, 105, 108 indicator light .........
Index Clock adjust 6-CD in dash .............................26 AM/FM/CD .................................21 Clutch fluid ..........................................264 operation while driving ..........172 recommended shift speeds ....174 Console ........................................47 overhead ....................................47 Controls power seat .................................72 Coolant checking and adding ..............247 refill capacities ................251, 269 Cruise control ..............
Index running out of fuel .................258 safety information relating to automotive fuels .....................253 Fuses ..................................185–186 G Gas cap (see Fuel cap) ............256 Gas mileage (see Fuel economy) .................258 Gauges .........................................19 engine coolant temperature gauge .........................................21 fuel gauge ..................................21 odometer ...................................21 tachometer .................
Index doors ..........................................58 Lug nuts ....................................203 Luggage rack ...............................57 Lumbar support, seats ...............72 M Manual transaxle .......................172 fluid, checking and adding ....267 reverse .....................................174 Manual transmission fluid capacities ........................269 Mirrors ...................................47, 50 fold away ...................................50 heated ...................
Index Safety Compliance Certification Label ....................273 Seat belts (see Safety restraints) ....................................79 Seats ............................................70 child safety seats ....................115 heated ........................................74 SecuriLock passive anti-theft system ..........................................65 Servicing your vehicle ..............235 Setting the clock AM/FM single CD .....................21 AM/FM/In-dash 6 CD ................
Index Windows power .........................................49 rear wiper/washer .....................46 Windshield washer fluid and wipers checking and adding fluid .....240 282 2006 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) checking and cleaning ....240–241 liftgate reservoir .....................240 operation ...................................45 replacing wiper blades ...........241 Wrecker towing .........................
