Table of Contents Introduction Instrument Cluster 4 12 Warning and control lights Gauges 12 18 Entertainment Systems 21 AM/FM AM/FM AM/FM AM/FM stereo stereo with single CD stereo with CD stereo cassette with single CD Climate Controls Heater only Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Speed control 21 25 32 45 68 68 69 73 73 75 75 82 82 83 85 89 Locks and
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving 105 107 119 131 148 Starting Brakes Transmission operation Vehicle loading Trailer towing 148 153 158 170 172 Roadside Emergencies 181 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing Customer Assistance Reporting safety defects (U.S.
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Refill capacities Lubricant specifications Engine data 224 234 238 243 250 272 275 276 Accessories 279 Index 280 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Mazda Motor Corporation.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control, vehicle rollover, personal injury or death. Be sure to read Driving off road in the Driving chapter.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Window Lockout Panic Alarm System Feature Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing.
Instrument Cluster Instrument panel dimmer control (pg. 74) Instrument cluster (pg. 12) Headlamp control (pg. 73) DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 30 20 1 CHECK FUEL CAP F ABS 10 0 P ! E 60 70 80 0 0 0 80 100 40 90 120 60 2 C 50 40 RPMx1000 140 000000 20 MPH R N D 2 1 160 100 180 110 km/h 120 H SPEED CONT L 4WD HIGH H 4WD LOW L THEFT BRAKE O/D OFF OFF DIM ON SET ACC OFF Turn signal and wiper/washer control (pg. 75) COAST Speed control* (pg.
Instrument Cluster Audio system (pg. 21) 4wd control* (pg. 167) 2WD 4X4 HIGH Auxiliary power point (pg. 84) VOL PUSH ON 4X4 LOW TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM OFF ON OFF OFF PASSENGER AIRBAG Fog lamp control (pg. 73) Passenger air bag deactivate switch (pg. 128) Climate control system (pg.
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the light remains on, have your vehicle serviced at the first available opportunity. CHECK NOTE: The ENGINE light will illuminate if vehicle refueling is conducted with the engine running. WARNING: Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your catalytic converter.
Instrument Cluster level or a brake system malfunction and the brake system should be serviced immediately by a qualified technician. Refer to Brakes in the Driving chapter for more information. WARNING: Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately. Anti-lock brake system (ABS) Illuminates to ensure the circuit is functional.
Instrument Cluster Passenger Air bag Deactivation switch warning light Illuminates to warn that the passenger air bag is deactivated, refer to Passenger Air Bag ON/OFF Switch in the Seating and Safety chapter. Charging system Illuminates when the battery is not charging properly. Check fuel cap Illuminates when the fuel cap is not CHECK installed correctly. Check the fuel FUEL cap for proper installation.
Instrument Cluster O/D off Illuminates when the overdrive function has been turned OFF using the transmission control switch (TCS). O/D OFF If the light does not come on or the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur. Turn signals Illuminates when the turn signals or the hazard lights are turned on. If the lights stay on continuously or flash faster, check for a burned-out bulb.
Instrument Cluster Four wheel drive low (if equipped) Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. 4WD LOW Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinderY chime Sounds intermittently to remind you to fasten your safety belts. Supplemental restraint system (SRS) warning chime Sounds when a malfunction in the supplemental restraint system (front or side airbags) has been detected.
Instrument Cluster GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. H C Refer to Engine coolant in the Maintenance and specifications chapter.
Instrument Cluster Engine oil pressure gauge Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range (the area between the “L” and “H”); H if the needle goes below the normal range, stop the vehicle as L soon as safely possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and Specifications chapter).
Instrument Cluster Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 50 40 60 70 80 0 0 0 80 100 60 30 20 10 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems AM/FM STEREO VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. 3 4 AM/FM VOL PUSH ON VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment Systems AM/FM select The AM/FM select control works in radio mode. AM/FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
Entertainment Systems Radio station memory preset 1 2 3 4 The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the TONE control three times, then use the volume knob to adjust the desired level. Setting the clock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control: • to decrease hours and • to increase hours.
Entertainment Systems when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock. In media mode, the media information will always be displayed.
Entertainment Systems Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Entertainment Systems Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next • Press listenable station up the frequency band. SEEK TUNE DISCS Seek function for CD mode • Press to seek to the previous SEEK track of the current disc. If a selection has been playing for TUNE DISCS three seconds or more and you , the CD changer will press replay that selection from the beginning.
Entertainment Systems Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE CD select • To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. AM FM CD This player is designed to use standard 4 5⁄8 compact discs.
Entertainment Systems Fast forward The fast forward control works in CD mode. To fast forward in CD mode, press CD the CD control (preset 2). 2 Pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. Eject function Press the control to stop and eject a CD. EJ Compression feature Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level.
Entertainment Systems Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. To set the hour, press and hold the CLK control. SCN CLK Press the SEEK control: • to decrease hours and • to increase hours. SEEK TUNE DISCS To set the minute, press and hold the CLK control. SCN CLK Press the TUNE control: • to decrease minutes and • to increase minutes.
Entertainment Systems MACHT MP3 MUSIC SYSTEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 32 ON/OFF and volume control AM/FM control Bass control Treble control Fade control Balance control Seek control Scan control Clock control Tune/Directory control 11. 12. 13. 14. 15. 16. 17. 18. 19.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Entertainment Systems • Press to move to the next frequency up the band. Hold for quick movement through the frequencies. When the top of the band is reached, the tuner will continue to select from the lowest frequency upward. When a radio frequency is in tune, the ST icon will appear in the display for stereo broadcasts. MP3 functions Your audio system is equipped with MP3 capability which allows you to listen to songs in MP3 flat file mode and MP3 directory mode.
Entertainment Systems Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD, MP3 flat file and MP3 directory modes • Press to select and play the previous track on the disc. If the current track is the first track on will select the disc, pressing the last track on the disc. to select and play the • Press next track on the disc.
Entertainment Systems Scan function in CD mode Press SCN to engage scan mode and to hear a brief sampling of all tracks on the disc. The track number in the display will blink while the scan function is enabled. When the end of the disc is reached, the player will continue to scan from the first track forward. Press SCN again to disengage scan mode. Scan function in MP3 flat file mode The scan function in MP3 flat file mode allows you to briefly audition all tracks on the MP3 disc.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select The CD select function allows you to play CDs.
Entertainment Systems Playing a CD • If a CD is already loaded, press the CD control. CD play will begin where it stopped last. • If a CD is not already loaded, insert the CD into the system. CD will briefly appear in the display and then the first track on the disc will begin playing. Playing an MP3 disc in MP3 flat file mode and MP3 directory mode • Insert an MP3 disc into the player. CD and LOAD will appear in the display.
Entertainment Systems • Press on the TUNE DIR control to advance to the next directory on the MP3 disc. If the current directory is the last directory on the disc, pressing will select the first directory on the disc. Press and hold for fast selection. • Press on TUNE DIR to revert to the previous directory on the MP3 disc. If the current directory is the first directory on the disc, pressing will select the last directory on the disc. Press and hold for fast selection.
Entertainment Systems Compression feature The compression feature works in CD, MP3 flat file mode and MP3 directory mode. Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate compression adjust. The compression icon (c) will illuminate in the display while the compression function is enabled. Press the COMP control again to disengage the feature.
Entertainment Systems • Press the SHUFFLE control to engage random play. SHF and then ON will briefly appear in the display. The player will then begin random play. • To select another random track or on on the disc, press the SEEK control. • Press SCN to scan through random tracks. The track number will flash in the display. The shuffle function will remain enabled. • Press SHUFFLE again to disengage the shuffle feature. SHF and then OFF will briefly display and the current track will continue to play.
Entertainment Systems • Press the SCN control to scan through random tracks in the current directory. The track number will flash in the display. The shuffle feature will remain enabled. To shuffle tracks in another directory, press or on the TUNE DIR control to select the desired directory. The shuffle function still remains enabled. Press the SHUFFLE control again to disengage the SHUFFLE feature. SHUF and OFF will briefly display and the current track will continue to play.
Entertainment Systems Repeat track function in MP3 flat file mode and MP3 directory mode. Press the REPEAT control to repeat the current track. The repeat icon will display and the current track will continue to repeat until the repeat function is disengaged. Press the REPEAT control again to disengage the feature. Error messages You may experience an error message for the following situations: • NO DISC when the CD control is pressed and there is not a CD present.
Entertainment Systems Saving and naming MP3 files • Your MACHt MP3 music system supports discs containing up to 255 files in 255 directories. Discs containing more than 255 files will not play. • Always save MP3 files with the .mp3 extension. The player recognizes an MP3 file by the .mp3 extension, so MP3 files saved with different extensions will not be played. Never save a non-MP3 file with the .mp3 extension as the file will not play properly and damage may occur to the player or your sound system.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the TAPE/CD select control. VOL - PUSH ON Turn control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment Systems • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next listenable station up the frequency band. • Press Seek function in tape mode • Press to listen to the previous selection on the tape.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with AM FM the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS TREB Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: • BASS TREB to decrease the treble output and • to increase the treble output.
Entertainment Systems Tape/CD select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • To begin CD play (if CD is loaded), press the CD control. TAPE CD The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last. Rewind The rewind control works in tape REW and CD modes.
Entertainment Systems Eject function Press the EJ control to stop and eject a tape or CD. DolbyT noise reduction Dolbyt noise reduction operates in tape mode. Dolbyt noise reduction reduces the amount of hiss and static during tape playback. EJ EJ control to activate Press the (and deactivate) the Dolbyt noise reduction. 4 Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing are registered Corporation.
Entertainment Systems Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press TUNE: AUTO CLK • to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Entertainment Systems Mute mode Press the MUTE control to mute the playing media. Press the MUTE control again to return to the playing media. EJ MUTE PREMIUM AM/FM STEREO IN DASH SIX CD RADIO SHUF DISC TUNE SCAN SEEK REW FF COMP MUTE EJ LOAD BASS BAL SEL TREB FADE PUSH ON AM FM CD 1 2 3 4 5 6 MENU Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Entertainment Systems AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune/disc adjust The tune control works in radio or CD mode.
Entertainment Systems Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. to find the next listenable station up the frequency band. • Press SEEK UP will display. Seek function in CD mode • Press to seek to the previous track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing.
Entertainment Systems Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the AM display as the frequency band is FM scrolled through. CD 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are fewer than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Entertainment Systems CD select CD mode may be entered by AM CD pressing the CD control and the FM LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs. NO CD will display if the CD control is activated when there is not a CD present in the audio system.
Entertainment Systems Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2.
Entertainment Systems Rewind The rewind control works in CD REW FF modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode. When in rewind mode, your audio system will automatically lower the volume level of the playing media. Fast forward The fast forward control works in REW FF CD modes. Press and hold the FF control until the desired selection is reached.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble.
Entertainment Systems While in FM mode, two menus are available. If RDS is turned OFF, you can access the following: • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES — Refer to Setting the clock. • RDS OFF — Refer to Radio data system feature. If RDS is turned ON, you can access the following: • TRAFFIC ON/OFF-Refer to Traffic announcements. • FIND type-Refer to Program type. • SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature. • RDS ON— Refer to Radio data system feature.
Entertainment Systems This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level. To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF.
Entertainment Systems • Press the MENU control until TRAFFIC is displayed. • Press the SEL control to engage the feature. The display will read TRAFFIC ON. This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level.
Entertainment Systems Show This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display. MENU + SEL With RDS activated, press the MENU control until SHOW is MENU + SEL displayed. Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display). Mute mode Press the control to mute the playing media.
Entertainment Systems MP3 DISC QUALITY FACTORS The MACHt MP3 music system is designed for use with CD-DA (regular audio discs), CD-R and CD-RW discs. Discs must comply with ISO 9660 and Joliet standards. Several factors can effect disc playback quality: • Disc capacity — Each disc contains about 650 MB of storage capacity. We do not recommend using high capacity discs containing 700MB of storage. • Disc type — Some CD-RW discs may operate inconsistently and may cause an error message to appear.
Entertainment Systems • Never insert any object other than a compact disc into the player, as doing so may damage the player and may cause injury to you. • Do not disassemble the player. The laser used in disc playback is extremely harmful to the eyes. CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players.
Entertainment Systems RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Climate Controls HEATER ONLY SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of the vehicle. • (Panel) – Distributes outside air through the instrument panel registers. • OFF – Outside air is shut out and the fan will not operate.
Climate Controls Operating tips • In humid weather, place the climate control system in DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, select any desired position. • To reduce humidity buildup inside the vehicle, do not drive with the climate control system in the OFF position. • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than OFF position when the vehicle is parked.
Climate Controls Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode Selector Control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor can operate in all modes except and . However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher.
Climate Controls • OFF – Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. • (Panel and floor) – Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
Climate Controls • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open.
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. OFF FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beams position. Press the foglamp control to activate the fog lamps. The fog lamp indicator light will illuminate. When the highbeams are activated, the fog lamps will not operate.
Lights High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. • In vehicles equipped with daytime running lights, use of the turn signals will shut off the highbeams in daytime driving. COURTESY/READING LAMPS (IF EQUIPPED) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF.
Lights Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to assure lamp performance, light brightness and pattern and safe visibility. NOTE: The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Lights Replacing headlamp bulbs WARNING: Handling Halogen Bulbs: When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass. If the glass portion of the bulb is touched with bare hands, body oil could cause the bulb to overheat and explode when lit. Never touch the glass portion of the bulb with your bare hands and always wear eye protection when handling or working around halogen bulbs.
Lights To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hands could cause the bulb to break the next time the headlamps are operated. NOTE: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly.
Lights 3. Remove screw(s) from lamp assembly. 4. Disengage lamp assembly (it has a snap fit). 5. Rotate bulb socket counterclockwise and remove from lamp assembly. 6. Carefully pull bulb straight out of socket and push in the new bulb. 7. Install the bulb socket in lamp assembly by turning clockwise. 8. Align the lamp on the vehicle and push to snap in place. 9. Install screw(s) on lamp assembly. 10. Install the headlamp on vehicle, push rearward and secure with two retainer pins.
Lights Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the tailgate to expose the lamp assemblies. 2. Remove the four screws and the lamp assembly from vehicle. 3. Rotate bulb socket counterclockwise turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket and push in the new bulb. 5.
Lights 3. Connect the electrical connector to the new fog lamp bulb. 4. Install the bulb socket in the fog lamp turning clockwise. Replacing high-mount brake lamp and cargo lamp bulbs The replacement of the high-mount brake lamp bulb and cargo lamp bulb is basically the same. This procedure covers the high-mount brake lamp bulb. To remove the brake lamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it counterclockwise. 3.
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds).
Driver Controls Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Driver Controls WARNING: Never adjust the steering wheel when the vehicle is moving. You could lose control of the vehicle. AUXILIARY POWER POINT SEEK 12V TUNE 1 2 3 4 AM-FM OFF A/C MAX A/C Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel.
Driver Controls POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
Driver Controls AUTOMATIC DIMMING REAR VIEW MIRRORS (IF EQUIPPED) Your vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the inside rear view mirror. When the inside rear view mirror detects bright light from behind the vehicle, the inside rear view mirror will automatically adjust (darken) to minimize glare.
Driver Controls OUTSIDE AIR TEMPERATURE Display operation of the mirror with the compass feature: • Press the right button to toggle the display between the compass direction and no display. Display operation of mirror with temperature and compass feature: • Press the right button once to display temperature °F and compass. • Press the right button twice to display temperature °C and compass. • Press the right button three times to turn the display OFF.
Driver Controls 3. To change the zone setting, push and hold the right button until ZONE appears in the display. 4. Press the right button repeatedly until desired compass zone number is displayed. The display will change back to the compass direction after 3 seconds when the button is not activated. COMPASS CALIBRATION ADJUSTMENT The compass calibrates itself under normal driving conditions. There is not a need for manual compass calibration. If calibration is still desired, follow these instructions: 1.
Driver Controls POWER MIRROR CONTROL (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left to adjust the right mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. NOTE: Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
Driver Controls To turn speed control off • Press OFF. NOTE: Once speed control is turned off or the ignition is switched off, the previously programmed set speed will be erased. ON OFF To set a speed • Press SET ACC. NOTE: For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Driver Controls To set a higher set speed • Press and hold SET ACC. Release the control when the desired vehicle speed is reached or • Press and release SET ACC to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACC. RSM SET ACC COAST NOTE: You can accelerate with the accelerator pedal at any time during speed control usage.
Driver Controls To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). NOTE: Disengaging the speed control will not erase the previously programmed set speed. NOTE: Fully depressing the clutch pedal may cause a flare in engine RPM as the throttle is returned to idle. This is normal. NOTE: Pressing OFF will erase the previously programmed set speed.
Driver Controls To return to a previously set speed • Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SPEED SET ACCEL or RES controls are pressed. It turns off when the speed CONT control OFF control is pressed, the brake or clutch is applied or the ignition is turned to the OFF position.
Driver Controls To return to normal overdrive mode, press the Transmission Control O/D ON/OFF Switch again. The O/D Off indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode. For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter.
Driver Controls CARGO AREA FEATURES Cargo area shade (if equipped) Your vehicle may be equipped with notches in the side trim panels that are used for a cargo area shade. See your dealer for more information. BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each side of the extender to release it from the pickup box. 3. Pivot extender on to the tailgate.
Driver Controls 4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security. To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 46 kg (100 lbs.) on the tailgate.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLocky Passive Anti-Theft System for more information. POWER DOOR LOCKS (IF EQUIPPED) Press the top of the control to unlock all doors and the bottom to lock all doors.
Locks and Security Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash.
Locks and Security Power door lock disable feature This feature will help protect your vehicle from unauthorized entry. The UNLOCK function on the power door control will not operate with the ignition OFF and twenty seconds after the doors are closed and electronically locked by the remote entry transmitter, key pad, or power door control (if pressed while the door was open).
Locks and Security Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Panic alarm will only operate with the ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Locks and Security Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself.
Locks and Security • When you have completed programming the remote transmitters, turn the ignition to 3 (OFF). Again the doors will lock/unlock to confirm programming has been completed. SECURILOCKY PASSIVE ANTI-THEFT SYSTEM SecuriLocky passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key is used. NOTE: The SecuriLocky passive anti-theft system is not compatible with non-Mazda aftermarket remote start systems.
Locks and Security Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your authorized Mazda dealership. Your dealership can program your key or you can “do it yourself.” Refer to Programming spare keys. The SecuriLocky passive anti-theft system is not compatible with aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Locks and Security If two previously programmed coded keys are not available, you must bring your vehicle to your dealership to have the spare coded key(s) programmed. NOTE: Please read and understand the entire procedure before you begin. NOTE: This procedure must be completed within the specified times. If not completed within the specified time period, the reprogramming procedure must be restarted from the beginning. 1.
Seating and Safety Restraints SEATING Adjusting the front manual seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. Sudden braking or a collision could cause serious injury. Adjust the seat only when the vehicle is stopped. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard and down on the seat handle. To stow the seat, pull seat bottom back to the fully upright position. WARNING: Do not install a child seat in a center facing jump seat.
Seating and Safety Restraints Center facing jump seat (4 door CabPlus) (if equipped) To open, pull seat assembly down, then raise seatback. To stow the seat, fold seat back down and raise seat assembly to the fully upright position. WARNING: Do not install a child seat in a center facing jump seat. SAFETY RESTRAINTS Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints WARNING: In a rollover crash, an unbelted person is significantly more likely to die or be seriously injured than a person wearing a seat belt. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger outboard safety belt has two types of locking modes described below: Energy Management Feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
Seating and Safety Restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints WARNING: After any vehicle collision, the entire seat belt system should be checked for proper operation by a qualified technician. Verify that the (automatic locking retractors” in all outboard seating positions are functioning properly. Additionally check that the (automatic locking mode( feature for child safety seat in the passenger outboard seating position is functioning properly.
Seating and Safety Restraints • Regular Cab and 4–door Cab Plus • 2–door Cab Plus To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder.
Seating and Safety Restraints Lap belts Adjusting the center lap belt The lap belt does not adjust automatically. WARNING: The lap belts should fit snugly and as low as possible around the hips, not around the waist. Failure to position the lap belt correctly may cause serious injury in an accident. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from).
Seating and Safety Restraints WARNING: The lap belts should fit snugly and as low as possible around the hips, not around the waist. Failure to position the lap belt correctly may cause serious injury in an accident. If you need to lengthen the belt, unfasten it and repeat the procedure above. To unfasten the belt, push in the release button prior to opening the rear door.
Seating and Safety Restraints BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... 9Crashes are rare events9 9I’m not going far9 9Belts are uncomfortable9 9I was in a hurry9 9Seat belts don’t work9 9Traffic is light9 9Belts wrinkle my clothes9 9The people I’m with don’t wear belts9 116 Consider... 36,700 crashes occur every day. The more we drive, the more we are exposed to 9rare9 events, even for good drivers.
Seating and Safety Restraints Reasons given... 9I have an air bag9 9I’d rather be thrown clear9 Consider... Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T 9PICK OUR CRASH9. WARNING: Do not sit on top of a buckled safety belt to avoid the Safety Belt Warning Light.
Seating and Safety Restraints BeltMinder activation and deactivation procedure 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation. 4.
Seating and Safety Restraints make sure there are no nicks, tears or cuts, replacing if necessary.
Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. WARNING: Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module. Always wear your safety belt.
Seating and Safety Restraints WARNING: Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off. See Passenger airbag ON/OFF switch in this chapter. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided.
Seating and Safety Restraints WARNING: Modifications to the front end of the vehicle, including frame, bumper, front end body structure, tow hooks and snow plows may effect the performance of the air bag sensors increasing the risk of injury. Do not modify the front end of the vehicle. WARNING: Additional equipment may effect the performance of the air bag sensors increasing the risk of injury. Consult your authorized Mazda dealership before installation of additional equipment.
Seating and Safety Restraints WARNING: Never place a rearward facing child safety restraint in front of an airbag. Airbags have been known to kill or injure children in front facing child safety restraints. Whenever placing a child safety seat in a front seating position (including center if equipped), turn off the passenger side air bag switch after being certain the child is properly restrained.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and Safety Restraints WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation or you may be burned. WARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints If any of these things happen, even intermittently, have the SRS serviced at your authorized Mazda dealership immediately. WARNING: Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles (including safety belt pretensioners) For disposal of air bags or air bag equipped vehicles, see your authorized Mazda dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel.
Seating and Safety Restraints WARNING: If the OFF light fails to illuminate when the passenger air bag switch is in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at you authorized Mazda dealership. WARNING: In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1.
Seating and Safety Restraints WARNING: The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the air bags in certain types of crashes. When you turn OFF your air bag, you not only lose the protection of the air bag, you also may reduce the effectiveness of your safety belt system, which was designed to work with the air bag.
Seating and Safety Restraints • the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front so that the driver can constantly monitor the child’s condition. 2. Child age 1 to 12.
Seating and Safety Restraints Transport Canada air bag deactivation criteria (Canada Only) 1. Infant: An infant (less than 1 year old) must ride in the front seat because: • my vehicle has no rear seat; • the rear seat in my vehicle cannot accommodate a rear-facing infant seat; or • the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can monitor the infant’s condition. 2.
Seating and Safety Restraints WARNING: This vehicle has special energy management safety belts for the driver and/or right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision. The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant’s chest and reduce the risk of certain bone fractures and injuries to underlying organs.
Seating and Safety Restraints WARNING: An air bag can kill or injure a child in a child seat. Child seats should never be placed in the front seats, unless passenger air bag switch is turned off, See Passenger air bag on/off switch. WARNING: Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off. WARNING: Do not install a child seat in a center facing jump seat.
Seating and Safety Restraints bend comfortably. Booster seats also make the shoulder belt fit better and more comfortably for growing children. When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs. The shoulder belt should cross the chest, resting snugly on the center of the shoulder.
Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and Safety Restraints • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps.
Seating and Safety Restraints WARNING: Rear facing child seats should NEVER be placed in the front seats unless the passenger air bag switch is turned off. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and Safety Restraints Installing child safety seats in the center front seating position WARNING: Use the appropriate tether anchor when mounting a child safety seat in the center seating position. See Child safety seats with tether straps in this chapter. 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The tether anchors in your vehicle are located on the back of the front seat cushion.
Seating and Safety Restraints WARNING: This anchor information applies to child safety seats equipped with tether straps. For child safety seats equipped with LATCH anchors, refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors in this chapter. 1. Position the child safety seat on the front seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position.
Seating and Safety Restraints The tether anchor is located on the rear lower portion of the passenger seat. 4. Clip the tether strap to the anchor. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Seating and Safety Restraints Center seating location 60/40 seats with folding armrest When installing a child safety seat in the center position, route the tether strap over the center arm rest and clip it to the center anchor. See next page for center seating location of vinyl 60/40 seat. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Seating and Safety Restraints Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinyl seat, route the tether strap through the guiding sleeve and clip it to the center anchor. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor.
Seating and Safety Restraints WARNING: Do not put the LATCH type seat in the center seat position — it only has one possible anchor point and the seat will not be properly attached. WARNING: If there are two LATCH seats to install — you can only mount one LATCH seat in this vehicle with the LATCH anchor bars. You need to mount the second seat with the center seat belt using the normal lap belt method. WARNING: Do not attach two seats to one LATCH anchor bar.
Seating and Safety Restraints WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as 4 the radio to operate while the 3 engine is not running. 5 2. LOCK, locks the steering wheel, automatic transmission gearshift 2 lever and allows key removal. 3. OFF, shuts off the engine and 1 all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Driving 1. Turn the key to 5 (START) without pressing the accelerator 4 pedal and release as soon as the 3 engine starts. The key will 5 return to 4 (ON). 2. If the temperature is above –12° 2 C (10° F) and the engine does not start within five seconds on the first try, turn the key to 1 OFF, wait 10 seconds and try again. If the engine does not start in two attempts, press the accelerator all the way to the floor and hold. Turn the key to the START position. 3.
Driving If you should experience cold weather starting problems on (Ed85) ethanol, and neither an alternative brand of (Ed85) ethanol nor an engine block heater is available, the addition of unleaded gasoline to your tank will improve cold starting performance. Your vehicle is designed to operate on (Ed85) ethanol alone, unleaded gasoline alone, or any mixture of the two. If the engine fails to start using the preceding instructions 1. Press the accelerator pedal 1/3 to 1/2 way to floor and hold. 2.
Driving WARNING: If you ever smell exhaust fumes of any kind inside your vehicle, have your authorized Mazda dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and result in accident or death. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service. • the sound of the exhaust system changes. • the vehicle has been damaged in a collision.
Driving squeal or groan noises when the brakes are applied. Such noises are usually heard during the first few brake applications in the morning; however, they may be heard at any time while braking and can be aggravated by environmental conditions such as cold, heat, moisture, road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by an authorized Mazda dealership.
Driving Using four wheel ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous force on the brake. The ABS will be activated immediately, thus allowing you to retain full steering control of your vehicle and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. WARNING: The Anti-Lock system does not reduce stopping distance.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! BRAKE WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle.
Driving If the steering wanders or pulls, the condition could be caused by any of the following: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn suspension components TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle.
Driving WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles.
Driving 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside emergencies chapter. WARNING: Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern.
Driving When the battery is disconnected or a new battery installed, the transmission must learn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will fully update transmission operation to its optimum shift feel. Understanding gearshift positions WARNING: Hold the brake pedal down while you move the gearshift lever from P (Park) to another position.
Driving (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. O/D ON/OFF O/D OFF Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in (Overdrive) position.
Driving 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear and will shift to 1 (First) after the vehicle decelerates to the proper vehicle speed. Forced Downshifts To gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor.
Driving PARKING 1. Apply the brake, depress the clutch and shift into N (Neutral). 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Driving RECOMMENDED SHIFT SPEEDS Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) Shift from: 4H 4L 1-2 14 km/h (10 mph) 5 km/h (4 mph) 2-3 32 km/h (22 mph) 11 km/h (9 mph) 3 -4 50 km/h (33 mph) 19 km/h (13 mph) 4 - 5 (Overdrive) 71 km/h (41 mph) 27 km/h (17 mph) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: 4H 4L 1 -2 16 km/h (10 mph) 6 km/h (4 mph) 2-3 26 km/h (19 mph) 10 km/h (8 mph) 3-4 43 km/h (28 mph)
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and 4WD Low is selected while the vehicle is moving, the 4WD system will not engage.
Driving Shifting from 2WD (2WD high) to 4X4 HIGH (4WD high) Move the 4WD control to the 4X4 HIGH position. 4X4 4X4 HIGH LOW 2WD Do not shift into 4X4 HIGH with the rear wheels slipping. Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WD 4X4 position at any forward speed. 4X4 HIGH LOW 2WD • You do not need to operate the vehicle in R (Reverse) to disengage your front hubs. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3.
Driving Shifting from 4X4 LOW (4WD low) to 2WD (2WD high) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 2WD position. 4X4 2WD HIGH 4X4 LOW Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4.
Driving Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern.
Driving Driving through deep water may damage the transmission. Replace rear axle lubricant any time the axle has been submerged in water. The rear axle does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair is required. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. You could lose traction and slip sideways.
Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
Driving • Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow.
Driving Special loading instructions for owners of pickup trucks and utility-type vehicles WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter. WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Driving Engine 2.3L 3.0L Dual Sport 4x2 w/manual transmission Rear axle Maximum Maximum Maximum ratio GCWR - kg trailer weight frontal area (lbs.) - kg (lbs.) of trailer m2 (ft2) Regular Cab All 2,177 (4,800) 744 (1,640) Equal to frontal area of vehicle All 2,722 (6,000) 1,161 (2,560) 4.64 (50) Cab Plus 3.0L Dual All 2,722 (6,000) 1,070 (2,360) 4.64 (50) Sport 4.0L Dual All 3,175 (7,000) 1,488 (3,380) 4.64 (50) Sport For high altitude operation, reduce GCW by 2% per 300 meters (1, 000 ft.) elevation.
Driving 4x4 w/manual transmission For definition of terms used in this table, see Vehicle loading earlier in this chapter. To determine maximum trailer weight designed for your vehicle, see Calculating the load earlier in this chapter. Maximum trailer weight is shown. The combined weight of the completed towing vehicle (including hitch, passengers and cargo) and the loaded trailer must not exceed the Gross Combined Weight Rating (GCWR). Engine 2.3L 3.
Driving 4x4 w/automatic transmission Rear axle Maximum Maximum Maximum ratio GCWR - kg trailer frontal area (lbs.) weight - kg of trailer (lbs.) m2 (ft2) Regular Cab 3.0L All 3,402 (7,500) 1,742 (3,840) 4.64 (50) Cab Plus 3.0L All 3,402 (7,500) 1,651 (3,640) 4.64 (50) 4.0L All 4,309 (9,500) 2,504 (5,520) 4.64 (50) For high altitude operation, reduce GCW by 2% per 300 meters (1, 000 ft.) of elevation. For definition of terms used in this table, see Vehicle loading earlier in this chapter.
Driving Do not install a single or multi-clamp type bumper hitch, or a hitch which attaches to the axle. Underbody mounted hitches are acceptable if they are installed properly. Follow the towing instructions of a reputable rental agency. Whenever a trailer hitch and hardware are removed, make sure all mounting holes in the underbody are properly sealed to prevent noxious gases or water from entering.
Driving The rated capacities (as shown in this guide) for trailer towing with the factory bumper are only valid when the trailer hitch ball is installed directly into the ball hole in the bumper. Addition of bracketry to either lower the ball hitch position or extend the ball hitch rearward will significantly increase the loads on the bumper and its attachments. This can result in the failure of the bumper or the bumper attachments. Use of any type of hitch extensions should be considered abuse.
Driving Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling. (For additional information, refer to the Driving with a 4–speed automatic transmission section in this chapter. • Anticipate stops and brake gradually.
Driving Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper. • do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper.
Driving 4x2 and 4x4 vehicles equipped with automatic transmissions: 4x2 vehicles with automatic transmissions or 4x4 vehicles with manual transfer cases and automatic transmissions, follow these guidelines for recreational towing: • Release the parking brake. • Turn the key in the ignition to the OFF/UNLOCKED position. • Place the transmission in N (Neutral). • Do not exceed a distance of 80 km (50 miles). • Do not exceed 56 km/h (35 mph) vehicle speed.
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Mazda Motor Corporation offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 60,000 km (36,000 miles), whichever occurs first on Mazda vehicles, and four years or 80,000 km (50,000 miles) on Mazda vehicles.
Roadside Emergencies If you need to arrange roadside assistance for yourself, Mazda Corporation will reimburse a reasonable amount. To obtain reimbursement information, U.S. Mazda vehicle customers call 1-800-241-3673. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006. ROADSIDE COVERAGE BEYOND BASIC WARRANTY In the United States, you may purchase additional roadside assistance coverage beyond this period through the Mazda Auto Club by contacting your Mazda dealer.
Roadside Emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside Emergencies Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. 28 24 20 16 12 8 4 To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 186 Fuse Amp Rating 5A 10A Passenger Compartment Fuse Panel Description Power mirror switch Daytime Running Lights (DRL), Back-up lamps, Transmission, Passenger air bag deactivation switch, Blower motor relay 7.5A Right stop/turn trailer tow connector — Not used 15A 4x4 control module 2A Brake pressure switch 7.5A Left stop/turn trailer tow connector — Not used 7.
Roadside Emergencies Fuse/Relay Location 18 19 Fuse Amp Rating — 25A 20 21 22 23 24 7.5A 15A 20A — 7.5A 25 26 — 10A 27 28 29 30 31 32 33 — 7.
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies 2.
Roadside Emergencies 190 Fuse/Relay Location 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Fuse Amp Rating — — — 40A** 20A** — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* 32 33 — 15A* 34 35 36 37 38 39 40 41 — — — — 10A* — — 20A* Power Distribution Box Description Not used Not used Not used Blower motor Auxiliary cooling fan Not used Not used Not used PCM memory Not used Fuel pump motor Headlamps A/C clutch relay Not used Not used ABS module Not used Trailer Tow Foglamp, Daytime Runnin
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 42 10A* 43 — 44 — 45A — 45B — 46A — 46B — 47 — 48 — 49 — 50 — 51 — 52 — 53 — 54 — 55 — 56A — 56B — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Right headlamp low beam (Resistor) Not used Wiper HI/LO relay Wiper park/run relay Fuel pump relay Trailer tow relay Starter relay Auxiliary cooling fan Not used Not used Not used Not used PCM Diode PCM Relay Blower motor relay A/C clutch relay Front washer pump relay 191
Roadside Emergencies 3.0L and 4.
Roadside Emergencies Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Fuse Amp Rating — — 40A** — — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* 32 33 34 35 36 37 38 39 40 41 42 43 — 15A* — — — — 10A* — — 20A* 10A* — Power Distribution Box Description Not used Not used Blower motor Not used Not used Not used Not used PCM memory Not used Fuel pump motor Headlamps A/C clutch solenoid Not used Not used ABS module Not used Trailer tow Foglamps, Daytime Running Lamps (DRL) Not used
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 44 — 45A — 45B — 46A — 46B — 47A — 47B — 48A — 48B — 51 — 52 — 53 — 54 — 55 — 56 — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Not used Wiper HI/LO Wiper park/run Fuel pump Trailer tow A/C clutch solenoid Front washer pump Fog lamps Fog lamp relay Not used Not used PCM Diode PCM Blower Starter CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Roadside Emergencies Temporary spare tire information Your vehicle may have a temporary or conventional spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible. It is not recommended that the vehicle be operated in 4WD modes with a temporary spare.
Roadside Emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, jack handle, wheel nut wrench Key, spare tire lock (if equipped) Location Under the vehicle, just forward of the rear bumper Regular Cab: behind seats and underneath the jack and tools cover SuperCab: stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Four-door models: stowed behind the front seats, be
Roadside Emergencies 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5.
Roadside Emergencies 4. If your vehicle is equipped with P265/75 R15 AT tires, do not stow a flat or inflated full size spare tire in the spare tire carrier. The flat full size tire should be stowed and tied down in the pickup box bed until it can be repaired. 5. If removed, install the spare tire carrier lock on the access hole above the bumper.
Roadside Emergencies 3. Block the diagonally opposite wheel. 4. Insert tapered end of the lug wrench behind hub caps and twist them off. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Roadside Emergencies • Rear WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. Never use the differential as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured. 7. Remove the wheel lug nuts with the lug wrench. 8.
Roadside Emergencies 10. Remove the jack and fully tighten the lug nuts in the order shown. 11. Stow the flat tire. Refer to Stowing the spare tire. 12. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13. Unblock the wheels. 1 3 4 5 2 JUMP STARTING YOUR VEHICLE WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Roadside Emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Mazda Motor Corporation has not approved a slingbelt towing procedure. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
Customer Assistance CUSTOMER ASSISTANCE (U.S.A.) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Customer Assistance CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer.
Customer Assistance Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer’s service facilities. personnel and equipment. We urge you to follow the above three steps in sequence therefore for most effective results. MEDIATION/ARBITRATION PROGRAM Occasionally a customer concern cannot be resolved through Mazda’s Customer Satisfaction Program. If after exhausting procedures in this manual, your concern is still not resolved, you have another option.
Customer Assistance Provincial Administrators may be reached locally as listed below: Province/Territory CAMVAP Number British Columbia & Yukon (604) 681–0312 Territories Alberta & Northwest Territories (403) 426–0650 Saskatchewan (306) 352–9259 Manitoba (204) 942–7166 Ontario (416) 596–8824 Atlantic Canada (902) 422–5413 Quebec (418) 649–1330 REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc.
Customer Assistance CUSTOMER ASSISTANCE (PUERTO RICO) Your complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Customer Assistance MAZDA IMPORTERS/DISTRIBUTORS U.S.A (Importer/Distributor) Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 TEL: 1 (800) 222–5500 (in U.S.A.) (949) 727–1990 (outside U.S.A.) (Distributor in each area) CANADA Mazda Canada Inc. 305 Milner Avenue, Suite 400 Scarborough, Ontario M1B 3V4 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO Plaza Motors Corp. (Mazda de Puerto Rico) P.O.
Customer Assistance ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle’s performance or safety system; the manufacturer’s warranty doesn’t cover this. Before you install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
Customer Assistance OUTSIDE THE UNITED STATES AND CANADA Government regulations in the United States require that automobiles meet specific emission regulations and safety standards. Therefore, vehicles built for use in the United States, its territories, and Canada may differ from those sold in other countries. The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries.
Customer Assistance (Note) If you live in the U.S.A., all correspondence to Mazda Motor Corporation should be forwarded to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922 P.O. Box 19734 Irvine, CA 92623–9734 Customer Assistance Center or toll free at 1 (800) 222–5500 If you live outside of the U.S.A., please contact the nearest Mazda Distributor. ( See the Mazda Importers/Distributors section of this manual).
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. • Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning PAINT CHIPS Your dealer has touch-up paint to match your vehicle’s color. Touch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND COVERS Aluminum wheel rims or covers are coated with a clearcoat paint finish.
Cleaning • 2.3L Engine • 3.
Cleaning • 4.0L Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use One Step Wash and Wax Concentrate, available at your local Mazda dealer. • If tar or grease spots are present, use Extra Strength Tar and Road Oil Removal, available at your local Mazda dealer.
Cleaning • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly. CLEANING THE INSTRUMENT PANEL Clean the instrument panel with a damp cloth, then dry with a dry cloth. Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel.
Cleaning WARNING: Do not use chemical solvents or strong detergents when cleaning the seat where the side air bag is mounted. Such products may contaminate the side air bag system and affect performance of the side air bag in a collision. The air bag may not function correctly and not provide any injury reduction benefits. LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • To clean, use a soft cloth with Deluxe Leather and Vinyl Cleaner.
Maintenance and Specifications INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer. Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.
Maintenance and Specifications Chart symbols I: Inspect, and if necessary correct, clean or replace A: Adjust R: Replace L: Lubricate Normal driving service intervals – perform at the months or distances shown, whichever occurs first.
Maintenance and Specifications Maintenance Interval (Number of months or km (miles), whichever comes first) Maintenance Item Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Miles 5 10 15 20 25 30 35 40 45 50 55 60 (x 1000 km) Drum brake system, lines and hoses Exhaust system for leaks, damage, looseness Manual transmission fluid Automatic *2 transmission fluid Exhaust system shielding (for trapped material) Propeller shaft U-joints (if equipped with grease fittings) Parking brake
Maintenance and Specifications 5. The California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty nor limit recall liability prior to completion of the vehicle’s useful life.
Maintenance and Specifications Maintenance Interval (Number of months or Miles (km), whichever comes first) Maintenance Item 52 56 60 64 68 72 76 80 x 1000 Miles 65 Months 70 75 80 85 90 95 100 105 110 115 120 84 88 92 96 (x 1000 km) (104) (112) (121) (128) (136) (144) (152) (160) (168) (176) (184) (192) Exhaust system for leaks, damage, looseness Manual transmission fluid Automatic *2 transmission fluid Exhaust system shielding (for trapped material) Propeller shaft U-joints (if equi
Maintenance and Specifications 5. The California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty nor limit recall liability prior to completion of the vehicle’s useful life. SCHEDULE II – SPECIAL OPERATING CONDITIONS If your driving habits FREQUENTLY include one or more of the following conditions: • Short trips of less than 16 km (10 miles) when outside temperatures remain below freezing.
Change Transfer Case Fluid (4x4) Lubricate Front Wheel Bearing (4x2) Inspect and Lubricate U-Joints Change Manual Transmission Fluid Replace Engine Air Filter Replace Spark Plugs Change Automatic Transmission Fluid Replace Fuel Filter Inspect Brake System Special Operating Conditions Replace Engine Oil and Filter Maintenance and Specifications 3,000 5,000 15,000 30,000 60,000 As As As 30,000 60,000 Suggested Maintenance miles or miles miles miles miles required required required miles miles Inte
Maintenance and Specifications • Note any changes in the sound of the exhaust or any smell or exhaust fumes in the vehicle. • Check for vibrations in the steering wheel. Notice any increased steering effort or looseness in the steering wheel, or change in this straight ahead position. • Notice if your vehicle constantly turns slightly or “pulls” to one side when traveling on a smooth, level road.
Maintenance and Specifications • Check battery water level (non-maintenance free). • Check battery connections and clean if necessary. SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance section which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Maintenance and Specifications • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 3.0L V6 engine 1 2 3 4 5 6 7 8 11 10 9 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Transmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (manual transmission) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11.
Maintenance and Specifications WINDSHIELD WASHER FLUID Windshield washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a UID SHER FL WA Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. ON LY RADIATOR COOLANT ONLY Only use a washer fluid that meets Mazda specification . Refer to Lubricant specifications in this chapter.
Maintenance and Specifications ENGINE OIL Checking the engine oil Refer to the service maintenance section for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and Specifications • 3.0L V6 engine • 4.
Maintenance and Specifications 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • 2.3L I4 engine • 3.
Maintenance and Specifications • 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use an equivalent oil Mazda specification. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and Specifications SAE 5W-30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use an equivalent Mazda Specification. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. Change your engine oil according to the appropriate schedule listed in the service maintenance section.
Maintenance and Specifications If possible, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Maintenance and Specifications RN LE TU AD RE 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift lever in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process.
Maintenance and Specifications A 50/50 mixture of distilled water and Mazda Genuine Engine Coolant provides: • maximum cooling system efficiency. • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant gauge. The engine coolant must be maintained at the correct fluid level and concentration to work properly.
Maintenance and Specifications • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the service maintenance section for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Maintenance and Specifications When the engine is cool, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir, until the coolant is at the “cold fill level” or within the “cold fill range” as listed in the engine coolant reservoir (depending upon application). • NEVER increase the coolant concentration above 60%. • NEVER decrease the coolant concentration below 40%.
Maintenance and Specifications Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter.
Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.
Maintenance and Specifications • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water.
Maintenance and Specifications WARNING: Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures, damage may occur and your warranty may be invalidated. WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.
Maintenance and Specifications 5. Turn the filler cap clockwise 1/8 of a turn until it stops. “Check Fuel Cap” illuminates when the ignition is turned to the ON position to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the Check Fuel Cap light on, can activate the Service Engine Soon warning. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving.
Maintenance and Specifications Octane recommendations Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are (R+M)/2 METHOD using fuel with the recommended octane rating, see your authorized Mazda dealership to prevent any engine damage. Unleaded Gasoline engines Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87.
Maintenance and Specifications Unleaded Gasoline engines If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your authorized Mazda dealership.
Maintenance and Specifications Replace the fuel filter with an authorized Mazda part. The customer warranty may be void for any damage to the fuel system if an authorized Mazda fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Maintenance and Specifications • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4.
Maintenance and Specifications • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy.
Maintenance and Specifications • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle.
Maintenance and Specifications Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the service maintenance section for the service interval schedules. If adding fluid is necessary, use only MERCONt ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3.
Maintenance and Specifications BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the service maintenance section for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened MAX container until the level reaches MAX. Do not fill above this line. 4.
Maintenance and Specifications CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to the service maintenance section for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Mazda specification. Refer to Lubricant Specifications in this chapter. WARNING: Brake fluid is toxic.
Maintenance and Specifications temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3.
Maintenance and Specifications The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Maintenance and Specifications Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Mazda specifications. Refer to Lubricant Specifications in this chapter.
Maintenance and Specifications Checking and adding transfer case fluid (if equipped) Vehicle must be on level surface. 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Mazda specifications. Refer to Lubricant Specifications in this chapter.
Maintenance and Specifications INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Maintenance and Specifications Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Maintenance and Specifications • Four tire rotation • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Maintenance and Specifications WARNING: When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely and an accident can occur.
Maintenance and Specifications • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously. If you hear the cables rub or bang against the vehicle, stop and retighten them. If this does not work, remove the cables to prevent vehicle damage. • If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads.
Maintenance and Specifications Fluid Mazda Part Name Mazda MERCONt ATF Mazda MERCONtV ATF Transmission fluid 1 Engine coolant 4 Application Capacity 5-speed manual 2.65L (2.8 quarts) 2 9.4L (9.9 quarts) 3 4x2 vehicles with automatic and 2.3L I4 engine 4x2 vehicles with automatic and 3.0L or 4.0L engines 4x4 vehicles with automatic and 3.0L or 4.0L Premium Engine 2.3 L I4 engine Coolant with manual transmission 2.3L I4 engine with automatic transmission 3.0L V6 engine with manual transmission 3.
Maintenance and Specifications Fluid Fuel tank Transfer Case Fluid Front axle lubricant Mazda Part Name N/A Application Capacity Regular cab (Short wheel base) Regular cab (Long wheel base) SuperCab 62.4L (16.5 gallons) 75.7L (20.0 gallons) 73.8L (19.5 gallons) 1.2L (1.25 quarts) 1.7L (3.6 pints) Mazda 4x4 Vehicles MERCONt ATF Mazda SAE 4x4 Vehicles 80W-90 Premium Rear Axle Lubricant Mazda SAE All 2.4-2.5L (5.0-5.
Maintenance and Specifications 5 Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier meeting Mazda specifications for complete refill of Traction-Lok axles. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole.
Maintenance and Specifications 1 Add 118 ml (4 oz.) of Additive Friction Modifier meeting Mazda specifications for complete refill of Traction-Lok axles. If submerged in water, the rear axle lubricant should be changed. 2 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCONt and MERCONt V are not interchangeable. DO NOT mix MERCONt and MERCONt V.
Maintenance and Specifications 3 5 2 4 1 277
Maintenance and Specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Accessories CELL PHONES Use of cell phones and other devices by driver: WARNING: Although not Mazda products, use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’s hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident.
Index A ABS (see Brakes) .....................154 Air bag supplemental restraint system ................................119–120 and child safety seats ............122 description ..............................120 disposal ....................................126 driver air bag ..........................124 indicator light .............14–15, 125 operation .................................124 passenger air bag ...................124 passenger deactivation switch ......................................
Index attaching with tether straps ..140 in front seat ............................136 in rear seat ......................136, 139 LATCH .....................................145 tether anchorage hardware ...140 Cleaning your vehicle engine compartment ..............219 exterior ....................................223 instrument cluster lens ..........222 instrument panel ....................222 interior .....................................222 mirrors .....................................221 plastic parts .
Index filter, specifications ................242 recommendations ...................242 refill capacities ........................272 specifications ..................275–276 Exhaust fumes ..........................152 F Flexible Fuel Vehicle (FFV) ....250 Fluid capacities .........................272 Foglamps .....................................73 Four-Wheel Drive vehicles ..........................16–17, 165 description ..............................165 driving off road .......................
Index warning chime ..........................17 Heating heater only system ...................68 heating and air conditioning system .......................................69 Hood ..........................................233 I Ignition ...............................148, 276 Infant seats (see Safety seats) ..135 Inspection/maintenance (I/M) testing ........................................260 Instrument panel cleaning ...................................222 cluster ................................
Index Mirrors automatic dimming rearview mirror ........................................86 cleaning ...................................221 side view mirrors (power) .......89 Motorcraft parts ........................255 O Octane rating ............................254 Odometer .....................................20 Oil (see Engine oil) ..................238 Overdrive .....................................93 P Panic alarm feature, remote entry system ..............................100 Parking brake ...........
Index Special notice ambulance conversions ..............7 utility-type vehicles ....................7 Specification chart, lubricants ...........................275–276 Speed control ..............................89 Speedometer ...............................20 Starting your vehicle ........148–150 jump starting ..........................201 Steering wheel controls ................................83, 89 tilting .........................................83 T Tachometer .................................
