® GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS PART NUMBER (s): APPLICABLE MODELS: REMOTE START SYSTEM 0000-8F-N02B 2007 > MAZDA CX-9 ALL MODELS NOTE: BOTH VEHICLE IGNITION KEYS ARE REQUIRED AT TIME OF INSTALLATION. DO NOT BEGIN INSTALLATION WITHOUT BOTH KEYS.
0 ELECTRICAL SYSTEM GENERAL PROCEDURES Wire color code Connector diagrams Two-color wires are indicated by a two-letter symbol.The first indicates the base color of the wire, the second the color of the stripe. For example: W/R is a white wire with a red strip BR/Y is a brown wire with a yellow strip Connector diagrams show connectors on the harness side. The terminal indicates the view from the harness side.
0 ELECTRICAL SYSTEM GENERAL PROCEDURES; continued Wire Tie Procedure 1.Wrap wire tie around the harnesses you wish to secure together. 3.Pull the Tapered End through the Wire Tie Head until the wire tie is snug. 2.Insert the Tapered End of the wire tie into the Wire Tie Head. 4.Trim wire tie end after tightening. Tapered End Wire Tie Head 1 VEHICLE PREPARATION 1. Disconnect and Remove Battery a. Disconnect and isolate the negative and positive battery terminals. (FIGURE A) b.
1 VEHICLE PREPARATION; continued b. Remove the driver’s side kick panel by removing the plastic nut. (FIGURE C) Partially peel back the rubber weatherstrip away from the kick panel. Insert a fiber stick between the body and kick panel to disengage the retaining clip. Gently pull the kick panel toward the passenger’s side of the vehicle to remove. Plastic Nut Fig. 1-4 FIGURE C c.
2 REMOTE START CONTROL MODULE PREPARATION 1. Insert the supplied fuses into the remote start control module as shown below. (FIGURE F) The fuses fit tightly, so use the flat tip of a fiber stick to push them in place, if necessary. 2. Install DNA card into the remote start control module as shown below. (FIGURE G) ! CAUTION: Use care to assure that both rows of the multi-pin connector are aligned and seated properly or the remote start system will NOT operate properly. 3.
4 DIPOLE ANTENNA MOUNTING A-PILLAR UPPER TRIM B 1. Driver’s A-Pillar Trim Removal/Installation A a. Partially peel back the rubber weatherstrip away from the A-pillar trim. A TAB b. Pull the A-pillar trim, then disengage clips A. (FIGURE K) CLIP B c. Pull the A-pillar trim, then disengage clip B (Picture 1). CLIP A GROMMET d. Pull the A-pillar trim upward, then disengage clip B from the A-pillar trim (Picture 2). A-PILLAR UPPER TRIM FIGURE K (1) (2) e.
5 HOOD SAFETY SWITCH MOUNTING 1. Using (2) supplied, 1/4” self drilling screws and (2) supplied lock washers, secure the hood safety switch to the drivers side of the vehicle’s hood 105 mm above the top of the hood mounting bracket and 70 mm from the side edge of the hood. (FIGURE P & Q) 2. Route the hood safety switch wiring down into the engine compartment along the inside of the hood hinge and secure using (1) supplied, short wire tie. (FIGURE Q) 3.
5 HOOD SAFETY SWITCH MOUNTING, continued 4. Using fish wire, pull the hood safety switch wiring and WHITE/BLACK tach wire from the remote start harness through the main wire harness grommet: a. From inside of the vehicle, bend approximately three (3) inches of tach wire at wire end. b. Using electrical tape, secure fish wire to tach wire as shown. (FIGURE S) c. Insert the fish wire along with tach wire through the main wire harness grommet into the engine compartment.
6 HOOD SAFETY SWITCH WIRE CONNECTIONS 1. Locate the BLACK and GRAY/RED wires from the remote start harness. 2. Using the (2) supplied IDC wire taps (in hood safety switch parts bag), connect the wires listed below together and crimp the IDC wire taps in place using pliers. Ensure that a complete and secure connection is made. HOOD SAFETY SWITCH WIRE REMOTE START HARNESS WIRE Dark GRAY Dark GRAY GRAY/RED BLACK NOTE: Switch is not polarity sensitive.
8 WIRE HARNESS CONNECTIONS - STEERING COLUMN IGNITION SWITCH CONNECTOR 1. Route the remote start ignition harness with 6-pin male and female ignition connectors over the factory harness, along the left side of the steering column. Do not secure harness at this time. 6-pin male ! CAUTION: EXTREME CARE MUST BE TAKEN TO ROUTE THE REMOTE START HARNESS AWAY FROM THE STEERING COLUMN ADJUSTER SPRING. 2. Locate the 6-pin WHITE ignition connector, on the left side of the steering column. 3.
8 WIRE HARNESS CONNECTIONS - STEERING COLUMN, continued KEY-IN-SENSE & PUSH WIRE ROUTING 1. Route the remote start harness YELLOW/BLUE and BROWN/BLACK wires along with the immobilizer interface ribbon cable behind the vehicle’s steering column harness to protect the wires from any potential damage from the steering column cover and tilt and telescopic steering wheel mechanism. (FIGURE Z) 2. Using (2) supplied, short wire ties, secure the remote start harness wires to the vehicle’s harness.
8 WIRE HARNESS CONNECTIONS - STEERING COLUMN, continued KEY-IN-SENSE CONNECTION 1. Locate the 12-pin (Smart-Key equipped) or 2-pin (Retractable Key equipped) WHITE key-in-sense connector under the ignition switch. (FIGURE AA) 2. Using a razor knife carefully cut back 1”-2” of the electrical tape to expose the wiring. ( ! CAUTION: BE EXTREMELY CAREFUL NOT TO DAMAGE ANY OF THE WIRES.) 12-pin/2-pin FIGURE AA I G E C K 3.
9 IMMOBILIZER INTERFACE RIBBON CABLE MOUNTING 1. Route the immobilizer interface ribbon cable to the ignition switch. 2. Following the instructions on the supplied adhesive primer stick, apply a thin coating to the outer surface of the immobilizer antenna coil (black plastic ring around ignition switch) and to the ribbon cable.
10 WIRE HARNESS CONNECTIONS - SECURING 1. Using (2) supplied, short wire ties, secure the remote start harness and immobilizer interface harness to the vehicle’s factory ignition wire harness. (FIGURE KK) NOTE: IT IS EXTREMELY IMPORTANT THAT THE WIRING IS SECURED IN A MANNER THAT WILL ALLOW THE TILT AND TELESCOPIC STEERING WHEEL TO MOVE FREELY AND STILL ALLOW FOR REASSEMBLY OF THE STEERING COLUMN SHROUD. CHECK FUNCTIONALITY OF THE TILT STEERING WHEEL PRIOR TO REASSEMBLY.
12 WIRE HARNESS CONNECTIONS - DRIVER’S KICK PANEL, continued DOME LIGHT CONNECTION 1. Locate the 6-pin WHITE connector at the Body Control Module mounted in the left kick panel area. (FIGURE PP) 2. Using a razor knife carefully cut back 1”-2” of the electrical tape to expose the wiring. ( ! CAUTION: BE EXTREMELY CAREFUL NOT TO DAMAGE ANY OF THE WIRES.) 6-pin 3. Using (1) supplied IDC wire tap, connect the wires listed below and crimp the IDC wire tap in place using pliers.
13 WIRE HARNESS CONNECTIONS - ENGINE COMPARTMENT TACHOMETER CONNECTION 1. Locate the upper 66-pin BLACK (2007 - 2010 Models) or the middle 70-pin BLACK (2011 Models) connector at the Powertrain Control Module mounted to the backside of the driver’s side strut tower in the engine compartment. (FIGURE TT) 2. Using a razor knife carefully cut back 1”-2” of the electrical tape to expose the wiring. ( ! CAUTION: BE EXTREMELY CAREFUL NOT TO DAMAGE ANY OF THE WIRES.) 3.
14 EMERGENCY OVERRIDE/PROGRAMMING BUTTON MOUNTING 1. Locate the previously removed driver’s side kick panel cover. 2. Drill a 9/32” hole at the top of the panel, exactly 12 mm down and 95 mm from the far edge. 3. Route the emergency override/programming button from the remote start harness down to the kick panel. 4. Mount the emergency override/programming button in the drilled hole from behind and screw the mounting cap in place.
15 RE-ASSEMBLY, continued f. Re-install the driver’s side scuff plate by engaging all three clips. (FIGURE ZZ) FIGURE ZZ 2. Re-install and Reconnect Battery: a. Carefully re-install battery into vehicle’s battery tray. b. Re-install battery hold-down bracket by engaging lower retainers into battery tray, away from vehicle dashwall and tightening both 10 mm nuts to 78-121 inch/pounds. (FIGURE AAA) 10 mm Socket c. Reconnect the positive battery terminal only, at this time.
18 TACHOMETER PROGRAMMING 1. Tachometer Programming - Make sure engine hood is closed! a. Turn the ignition key to the RUN position. b. Press and hold the programming button. After 10 seconds the horn will beep 3 times. c. Release the programming button. d. Press and release the programming button a second time. The horn will beep 4 times, indicating that the system has entered option learn mode. e. Press and release the brake pedal.
19 IMMOBILIZER INTERFACE PROGRAMMING NOTE: THE TACHOMETER SIGNAL MUST BE PROGRAMMED TO THE DNA CARD FOR THE REMOTE ENGINE START FUNCTION TO OPERATE. (READ ENTIRE PROGRAMMING PROCEDURE PRIOR TO PROGRAMMING.) 1. Transponder interface programming: NOTE: Two programmed ignition keys are required for this step and engine hood must be closed. For Smart-Key equipped vehicles, remove keys from Smart-Key transmitters and place transmit ters at least 10 feet away from vehicle during programming. a.
FUNCTION TEST Car Find 1. Press and hold START button - Horn should beep six times and parking lights should flash six times. Remote Engine Start Functions 1. REMOTE ENGINE START - Make sure the key is removed from the ignition switch and the engine hood is closed. Press the START button twice within 3 seconds. The parking lights should flash one time, the horn should beep once, then the vehicle should crank and start.
TROUBLESHOOTING GUIDE 1. Horn honks 4 times & vehicle does not remote start - No tachometer signal learned to DNA card. a. Ensure good connection and correct vehicle wire at PCM in engine compartment (See Section 13). b. Re-program tachometer signal (See Section 18). 2. Starter cranks too long during remote start operation. a. Re-program tachometer signal (See Section 18) and allow engine to warm up to a normal idle rate (Less than 1000 RPMs). 3.
22 TROUBLESHOOTING GUIDE, continued 9. Vehicle’s Perimeter Alarm sounds during remote start operation. a. Ensure remote start dome light fuse is placed in the (+) positive position (See Section 2). b. Ensure the Yellow/Blue remote start wire is routed properly and is not cut or shorted on any vehicle components (See Section 8). c. Ensure good connection and correct vehicle wire at Key-in-sense connector (See Section 8). 23 FINALIZING THE INSTALLATION 1.
HOOD SAFETY SWITCH ADJUSTMENT The hood safety switch will need to be adjusted to shut down the vehicle when the engine hood is raised to the full upright position. 1. Raise and prop the vehicle’s engine hood. 2. The hood switch cylinder should be bend away from the hood to approximately 15 degrees above parallel with the ground. (FIGURE CCC) 3. After the adjustment has been made, verify that remote engine start does not engage when the vehicle’s engine hood is open. 4.
SYSTEM LAYOUT 25 4280159 Rev.
FINAL INSPECTION • Inspect the installed / reinstalled parts for the following items: Inspection Items ( ) Inspection Parts Clearance / Fit Scratches / Dirt / Harness Interference Installation / Tightening / Engagement Negative battery terminal and battery hold downs Driver-side scuff plate Driver-side door seal Driver-side kick plate Driver-side A-pillar trim Driver-side lower dash panel Steering column cover Programming button installed Remote Engine Start features: - car find - remote start/stop - u
