Dolphin Wave 75 Pool Cleaner EN Operating Instructions 8152240
EN Robotic Pool Cleaner Dolphin Wave 75 Operating Instructions Contents 1. INTRODUCTION .............................................................................3 2. SPECIFICATIONS ............................................................................3 3. WARNINGS AND CAUTIONS ........................................................3 3.1 Warnings .................................................................................3 3.2 Cautions ........................................................
Robotic Pool Cleaner Dolphin Wave 75 Operating Instructions 1. INTRODUCTION Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions and all-surface climbing brush enhance maximum pool hygiene. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting performance and easy maintenance. 2.
. POOL CLEANER PARTS Robotic Pool Cleaner Model Dolphin Wave 75 Remote control unit Brushes Combined Brush All surface climbing brush ideal for most pool surfaces Optional Brushes Wonder Brush For smooth ceramics. PVC Brush For concrete, PVC, fiberglass and liner.
. USING THE POOL CLEANER 5.1 Set Up Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up with the groove in the socket on the power supply and turning clockwise (2). 40°C Max 104°F Max GFI/ELI <30 VDC; IP <30 VDC; 54 IP 54 3.5 m (12 ft) 5.2 Putting the Pool Cleaner into the pool If Wonder brush/ Wonder rings are dry, soak them in water until soft. ° ° Shake the robot from side to side or turn it upside down to release trapped air.
5.3 Removing the Pool Cleaner from the pool OFF The robot will perform automatic shut-off at the end of the cleaning cycle. CAUTION <30 VDC; IP 54 Turn OFF and unplug the power supply. B A C Using the floating cable, bring the Pool Cleaner to the pool’s edge. Using the handle remove the Pool Cleaner from the pool. CAUTION DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE. 5.4 Maintenance Filter bag Clean the filter bag with a hose. Periodically clean the brushes with a hose.
Cleaning the impeller Unplug the power supply. If you notice debris trapped in the impeller open the impeller and remove the debris. Ph Ph A No. 2 B Cable To remove the kinks, stretch the cable out completely and let it sit for at least a day in the sun. 5.5 Off-season storage If the pool cleaner will not be in use for an extended period, perform the following storage steps: • Make sure that no water is left in the pool cleaner. • Thoroughly clean the filter bag and insert in place.
6. POWER SUPPLY Digital “Switch-Mode” Power Supply with full filter bag and delay indicator. • • • • • Input - 100 VAC – 250 VAC 50 Hz – 60 Hz 180 W Output - <30 VDC IP 54 <30 VDC; IP 54 Delay indicator Full filter bag indicator <30 VDC; IP 54 On/Off switch Reset button Full filter bag indicator and Reset button The power supply is equipped with a filter bag status indicator. The red LED indicates two filter conditions. • When blinking - The filter is partially blocked.
7. REMOTE CONTROL UNIT The Control Panel Radio reception meter When no black lines are showing, move closer to the power supply unit Battery level meter When flashing, change the batteries The remote control unit offers two operation modes Automatic mode and manual direction control mode. Manual control indicator When flashing, you are in manual direction control mode Cleaning cycle icons In automatic mode, the cleaning parameters can be changed.
Press the Manual/Automatic select button and then choose the desired parameters according to the following table: Cleaning cycle indicator This determines the length of the cleaning cycle. Fast 2-hour cycle Efficient 3-hour cycle for everyday use. (Default setting) Extra 4-hour cycle Delay time indicator This determines when the pool cleaner starts to work. Delaying allows the dirt to settle to the bottom of the pool.
Dolphin Wave 75 Pool Cleaner EN Caddy assembly 11
1 1 DIN 7985 A2 M5X35 x2 2 DIN 127B A2 M5 x2 3 DIN 1587 A2 M5 x2 4 WN 1412 A2 KA50X16 x6 2 4 4 3a 3b 4 4a 4b 4c * For Liberty models 12
5 6 3 3 2 1 8mm (5/16”) 2 1 7 8 4 4 9 10 * For Remote Control models 13
Dolphin Wave 75 Pool Cleaner 8152240 www.maytronics.
