Robotic Pool Cleaner Basic 13 / Classic 13 / Classic 13+ User Instructions 8151870
Robotic Pool Cleaner Basic 13 / Classic 13 / Classic 13+ User Instructions Contents 1. INTRODUCTION ...................................................................... 2 2. SPECIFICATIONS...................................................................... 2 3. WARNINGS AND CAUTIONS .................................................. 2 3.1 Warnings ............................................................................ 2 3.2 Cautions .................................................................
Robotic Pool Cleaner Basic 13 / Classic 13 / Classic 13+ User Instructions 1. INTRODUCTION Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost-effective pool cleaning. Its reliable filtration in all pool conditions and active brushing, enhance pool hygiene. Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, long-lasting performance and easy maintenance.
. POOL CLEANER PARTS Robotic Pool Cleaner Model Classic 13/ Classic 13+ Power supply options Filtration options Caddy kit - optional Robotic Pool Cleaner Basic 13 / Classic 13 / Classic 13+ | User Instructions 3
. USING THE POOL CLEANER 5.1 Setup Before using the Pool Cleaner for the first time, perform the following steps: 11 cm (4 in) 3.5 m (12 ft) Position the power supply so that it is approximately in the middle of the long side of the pool at a distance of min 3.5 m (12 ft) from the pool and placed 11 cm (4 in) above ground. 5.1.1 5.1.2 Unwind the cable and stretch it out completely so that it has no kinks. 1 2 3 5.1.
5.2 Putting the Pool Cleaner into the pool ON 5.2.1 Put the Pool Cleaner into the pool. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions. 5.2.2 Turn the power supply ON. The Pool Cleaner will now operate until it has reached the end of the cleaning cycle. 5.
5.4 Removing the Pool Cleaner from the pool CAUTION Turn OFF and unplug the power supply. 5.4.1 5.4.2 Using the floating cable, bring the Pool Cleaner to the pool’s edge. Using the handle, remove the Pool Cleaner from the pool. CAUTION 5.4.3 6 DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE. Place the Pool Cleaner on the edge of the pool and let the water drain out.
6. CLEANING THE DUAL FILTER BASKET CAUTION Make sure the power supply is switched off and unplugged. It is highly recommended to clean the filter basket after each cleaning cycle. Note: Do not let the filter panels dry out before cleaning. 6.1 Cleaning after use - removing and cleaning the dual filter basket 6.1.1 6.1.2 Upon opening the filter cover, the handle will lift independently. Open the filter cover. 1 2 6.1.3 Lift up the basket. 6.1.
6.2 Periodic filter cleaning – recommended at least once a month Dismantle the 4 ultra-fine filter panels of the outer basket, according to the following steps: 6.2.1 Holding down the handle, remove the inner net basket. 6.2.2 Dismantle the panels, starting by pressing on panel 1 using your thumbs. Continue to dismantle the panels in the order of their numbers: 2 — >3— > 4. Assemble the filter panels according to the >3— >2— > 1. following order: Panel 4 — 6.2.4 Clean the filter panels with a hose.
7. CLEANING THE IMPELLER 7.1 If you notice debris trapped in the impeller: CAUTION Make sure the power supply is switched off and unplugged. Clean the debris trapped in the impeller opening, according to the following steps: 1 2 3 7.1.1 7.1.2 7.1.3 7.1.
7.2 Assemble the impeller compartment according to the next steps: 7.2.1 7.2.2 8.
9. TROUBLESHOOTING If the suggested solutions do not solve the problem, please contact your dealer or Service Center. Symptom Possible reason Corrective action The power-supply • No voltage in the power socket in the wall. • Check that there is voltage in the power socket in the wall. or its switch led • The power supply is not switched ON. • Check that the power supply is plugged in and turned ON. are not working.
