Installation Instructions

5
3. Apply masking tape to the end of a 7 mm (⁹⁄₃₂") nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and
remove by turning it counterclockwise and lifting out. Set gas
orifice spud aside.
4. Locate the nameplate on the range. It will be located on the
front frame behind the oven door or drawer front depending
on model. Identify the burner ratings for this range from the
nameplate.
Refer to the following chart for the gas to be used after the
conversion. Identify the correct replacement orifice spuds
using the nameplate burner ratings. The colors and ID
number are marked on the hex flats of the orifice spuds.
Natural Gas Orifice Spud Chart for Surface Burners
*Same orifices as shipped from factory for Natural gas.
LP Gas Orifice Spud Chart for Surface Burners
NOTE: Refer to the Model Number and Serial Number Plate
located on the oven frame behind the top left side of the oven
door for proper sizing of spuds for each burner location.
5. Save the replaced orifice spuds in a plastic bag or other
container.
6. Replace the burner base using both screws.
7. Replace burner cap.
8. Repeat steps 1-7 for the remaining burners.
To Convert Oven Bake Burner
1. Remove the oven racks.
2. Remove 2 screws at the rear of the oven bottom.
3. Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
A. Orifice spud
B. Orifice spud holder
C. Screw
D. Spark electrode
A. Hex flat
Nameplate Burner
Ratings (sea level)
Replacement Orifice - Natural
gas (high altitude)
Natural Gas LP Color Size ID
Number
18,000 BTU 14,200 BTU Red/
Orange
1.90 mm N190
17,000 BTU 14,200 BTU Red/
Orange
1.90 mm N190
15,000/
15,500 BTU
14,200 BTU Red/
Orange
1.90 mm N190
13,000/
13,500 BTU
11,000 BTU Yellow/
Magenta
1.70 mm N170
12,000/
12,500 BTU
11,000 BTU Yellow/
Magenta
1.70 mm N170
9,500 BTU 8,000 BTU Red/
White
1.40 mm N140
8,000 BTU 8,000 BTU Red/
White*
1.40 mm N140
5,000 BTU 5,000 BTU Red/
Brass*
1.10 mm N110
B
A
C
D
XXX
A
Nameplate Burner Ratings
(sea level)
Replacement Orifice - LP gas
(high altitude)
Natural Gas LP Color Size ID
Number
18,000 BTU 14,200 BTU Yellow/
Brown
0.99 mm L99
17,000 BTU 14,200 BTU Yellow/
Brown
0.99 mm L99
15,000/
15,500 BTU
14,200 BTU Yellow/
Brown
0.99 mm L99
13,000/
13,500 BTU
11,000 BTU Yellow/
Black
0.88 mm L88
12,000/
12,500 BTU
11,000 BTU Yellow/
Black
0.88 mm L88
9,500 BTU 8,000 BTU Yellow/
Green
0.84 mm L84
8,000 BTU 8,000 BTU Yellow/
Green
0.84 mm L84
5,000 BTU 5,000 BTU Yellow/
Silver
0.65 mm L65
A. Screws
B. Oven bottom
A
B