Instruction Sheet

Figure 2 - Side by Side Classic Euro-Style
NOTE: Measurements from the side edge of the door will
depend on specific application.
2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure up
from the bottom hole to determine the location of the second
hole. Countersink both holes on the inside of the panel, ¹⁄₄"
(6.35 mm) deep and ⁵⁄₈" (1.58 cm) diameter for screw head
clearance.
3. Install two mounting studs to the custom panel using the
screws provided. Make sure the head of the screw is flush
with the panel.
4. Install handle to handle mounting studs and tighten the
setscrews. Some adjustments of the handle mounting studs
may be required to allow the handle to fit over both mounting
studs.
NOTE: For products with one refrigerator door, the setscrew
should face the hinge side of the door. For products with two
refrigerator doors, the setscrews should face the center of the
product.
5. If you have two refrigerator doors or a side-by-side freezer
door, repeat steps 1 through 4 to install the other handle.
Install the Freezer Drawer Handle
IMPORTANT: For model specific hole location and the spacing
requirements for mounting the handles onto the panels, see
Figure 3 and the following Freezer Drawer table.
1. Measure from the side of the custom panel and mark your
first hole location as shown in Figure 3 and the Freezer
Drawer table.
Figure 3 - Freezer Drawer
NOTE: Measurements from the top edge of the door will
depend on specific application.
2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure from
that hole over to the second hole. Countersink both holes on
the inside of the panel, ¹⁄₄" (6.35 mm) deep and ⁵⁄₈" (1.58 cm)
diameter for screw head clearance.
3. Install two mounting studs to the custom panel using the
screws provided. Make sure the head of the screw is flush
with the panel.
4. Install handle to handle mounting studs and tighten the
setscrews. Some adjustments of the handle mounting studs
may be required to allow the handle to fit over both mounting
studs.
NOTE: The freezer handle setscrews should face down.
#10-24 x 1" Screws
60¹⁄₂"
(153.7 cm)
26¹⁄₂"
(67.3 cm)
Handle mounting stud
46¹⁄₂"
(118.1 cm)
6⁷⁄₈"
(17.5 cm)
Setscrews
Freezer Drawer
Handle Type A B
Bottom Mount
Classic
Euro-Style
5 ¹⁄₄"
(13.34 cm)
24 ³⁄₄"
(62.87 cm)
Euro-Style 5 ²⁷⁄₃₂"
(14.84 cm)
23 ⁹⁄₁₆"
(59.85 cm)
Pro 5 ²⁷⁄₃₂"
(14.84 cm)
23 ⁹⁄₁₆"
(59.85 cm)
French Door
Bottom Mount
Classic
Euro-Style
8 ²⁷⁄₃₂"
(22.46 cm)
23 ⁹⁄₁₆"
(59.85 cm)
Euro-Style 5 ¹⁄₄"
(13.34 cm)
30 ³⁄₄"
(78.11 cm)
Pro 5 ¹⁄₄"
(13.34 cm)
30 ³⁄₄"
(78.11 cm)
Handle
Mounting Studs
Freezer
Compartment
Handle
Custom Freezer
Compartment Panel
#10-24 x 1" Screws
B
A
Setscrews