Installation Instructions Over the Range Microwave Oven BEFORE YOU BEGIN Read these instructions • • and carefully. • Note to Consumerfuture reference. • Skill level - Installation of this appliance basic mechanical and electrical skills. and ordinances. • Proper installation installer. Note to InstallerBe sure to leave these instructions with the Consumer. • Product failure due to improper covered under the Warranty.
Installation Instructions CONTENTS General information C Important Safety Instructions Electrical Requirements ..................... 3 .............................. 3 Outside Back Exhaust ............................. Preparing Attach Damage ........................................... - Shipment/Installation 4, 5 ................. 6 Parts Included ............................................... 6 Tools You Will Need ..................................... 7 Mounting 7 Space ........
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following ductwork chart describes an example of one possible DUCT PIECES to the outside. If you plan to installation. EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct (6" Round) 12 Ft. x (1) = 12 Ft. x (1) = 5 Ft.
Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 3¼" x 10" rectangular or 6" diameter round duct should not exceed 60 equivalent feet. Maximum Outside ventilation requires a HOOD DUCT. Read the following carefully. EXHAUST Elbows, transitions, wall and roof caps, etc.
Installation Instructions DAMAGE - SHIPMENT/ INSTALLATION • PARTS INCLUDED HARDWARE If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure .....
Installation 1.PLACEMENT Instructions OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1, Remove the installation instructions, B. FINDING THE WALL STUDS Exhaust adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam. 1.
Installation C. DETERMINING Plate position - beneath Instructions WALL PLATE LOCATION UNDER YOUR CABINET flat bottom cabinet Draw a vertical line on the wall at the center of the 30" wide space. Tape the Rear Wall Template onto the wall matching the centeriine and touching the bottom of the cabinet. Plate position - beneath cabinet bottom framed recessed 33" to Cooktop Draw a vertical line on the wall at the center of the 30" space.
Installation D. ALIGNING Instructions THE WALL PLATE i i REAR WALk TEMPLATE _;:_,,_!_: ........................ Centedine notches __ Draw a Vertical Line on Wall from Center ____ of Top Cabinet o I'''- Horizontal Line o o o 7 Area E Hole B Horizontal Draw a Horizontal Line line on wall from bottom of "Rear Wall Template". CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1, Draw a Vertical line on the wall at the center of the NOTE: Holes A, B and C are inside area E.
Installation 2. INSTALLATION TYPES This microwave oven is designed for adaptation the following three types of ventilation: A. Recirculating (Non-Vented B. Outside Top Exhaust C. Outside Back Exhaust Instructions (Choose A, B or C) to NOTE: This microwave is shipped assembled for "Recirculating". And exhaust adaptor is shipped after being assembled to the filler-upper. Select the type of ventilation required for your installation and proceed to that section.
Installation A. RECIRCULATING (Non-Vented INSTALLATION OVERVIEW A1. Attach Plate to Wall Mounting Instructions Ductless) A2. Prepare Top Cabinet A3. Mount the Microwave Oven AI.__.ATTACH THE MOUNTING TO THE WALL PLATE 3. Place the mounting plate against the wall and insert the toggle wings into the holes on the wall to mount the plate.
Installation MOUNT THE MICROWAVE Instructions OVEN Cabinet Front Cabinet Bottom Shelf Filler Block _ FOR EASIER SAFETY, INSTALL INSTALLATION WE RECOMMEND THIS MICROWAVE IMPORTANT: installation. quivalent to Depth of AND PERSONAL THAT TWO OVEN. Do not grip or use handle Cabinet Recess PEOPLE igning Screw Microwave during 4, Attach the microwave NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
Installation B. OUTSIDE TOP EXHAUST INSTALLATION OVERVIEW B1. Attach Plate to Walt Mounting Instructions (Vertical Duct) B2. Prepare Top Cabinet B3. Adjust Blower B4. Check Damper Operation B5. Mount Microwave B6. Adjust Exhaust B7. Connect Oven Adaptor Ductwork Blm ATTACH THE MOUNTING TO THE WALL PLATE To use toggle bolts: Spacing for Toggles More Than Wall Thickness i i Toggle Wings i Mounting Plate _1_ O_ Wall Bolt End 3. Attach the plate to the wall using toggle bolts.
Installation B2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET Instructions 3. Carefully slide the blower motor toward the right, and lift it partially out of the opening. Note: The blower wires are long enough to allow flexible handling while performing these steps. Disconnect the wires if necessary for additional flexibility. You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout barge enough for the exhaust adaptor. f 4.
Installation 7. Secure the blower two screws sRceteawn i_ unit to the microwave removed __ screw etaining cover and secure FOR EASIER SAFETY, INSTALL it with the INSTALLATION WE RECOMMEND THIS MICROWAVE AND PERSONAL THAT TWO PEOPLE OVEN. in Step 1. 9. Attach the exhaust adaptor IMPORTANT: installation. to the rear of the microwave by sliding it into the guides center of the back of the oven.
Installation B5.m.. MOUNT THE MICROWAVE Instructions OVEN B6. ADJUST THE EXHAUST ADAPTOR (cont.) Open the top cabinet and adjust the exhaust to connect to the house duct. Cabinet Front Back of Microwave Cabinet Bottom Shelf Filler Block ._ Depth of Cabinet Equivalent to Recess For Front-to-Back Seif-Aligning or Side-to-Side Adjustment, Slide the Exhaust Adaptor as Needed. Screw Microwave Oven Top 4, Attach the microwave adaptor oven to the top cabinet.
Installation C, OUTSIDE BACK EXHAUST INSTALLATION C1. Prepare C2. Attach Instructions (Horizontal Duct) OVERVIEW Rear Wall Mounting Plate to Wall C3. Prepare Top Cabinet C4. Adjust Blower C5. Mount the Microwave Oven ÷ ...... I Clm PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rearwall exhaust. C2m ATTACH THE MOUNTING TO THE WALL PLATE for outside Attach the plate to the wall using toggle bolts.
Installation C2.__. ATTACH THE MOUNTING TO THE WALL (cont.) Instructions PLATE C4. ADAPTING MICROWAVE BLOWER FOR OUTSIDE EXHAUST To use toggle bolts" 1. Remove Spacing for Toggles More Than Wall Thickness retaining the back top center blower BACK motor door screw. I Toggle Wings Mounting Plate Blower Back of Blower Motor Screw Belt End 3. Place the mounting plate against 2. the wall and Open the blower motor by lifting it up at the back side of the microwave.
Installation Instructions MOUNT THE MICROWAVE 5. Roll the blower unit so that the right exhaust OVEN outlet faces the rear. Snap the inlet sleeve back onto the left side with the opening facing down. Note: The left side sleeve opening must always face downward. Reinstall the 2 screws holding the inlet sleeve to the motor assembly. FOR EASIER SAFETY, INSTALL INSTALLATION WE RECOMMEND THIS MICROWAVE IMPORTANT: installation.
Installation C5.__.MOUNT THE MICROWAVE Instructions OVEN (cont.) 4. Attach the microwave oven to the top cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block -_ Depth of Cabinet Recess Equivalent to gning Screw Microwave Oven Top 5. Insert 1 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Right 6, Tighten Screw. the outer two screws to the top of the microwave oven.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE 1, Make sure the microwave installed according 2, Remove all packing 6. oven has been material 7, KEEP INSTALLATION from the microwave THE LOCAL 3. Install turntable electrical and ring in cavity. house fuse or turn breaker 5, Plug power Manual. to instructions. oven. 4. Replace Read the Owner's cord into a dedicated back on. 20 amp outlet. 22 INSTRUCTIONS INSPECTOR'S USE.
Installation Instructions NOTE 23
Part No. : 8101 P679-60 Form No. : A/08/05 Code No.
