Owners Manual
Table Of Contents
- RANGE SAFETY
- Range Safety
- RANGE MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- Gas Supply Requirements
- INSTALLATION
- Unpack Range
- Install Anti-Tip Bracket
- Make Gas Connection
- Verify Anti-Tip Bracket Is Installed and Engaged
- Level Range
- Electronic Ignition System
- Warming Drawer or Premium Storage Drawer (on some models)
- Storage Drawer (on some models)
- Oven Door
- Complete Installation
- GAS CONVERSIONS
- Propane Gas Conversion
- Natural Gas Conversion
- Moving the Range
- SECURITE DE LA CUISINIERE
- Sécurité de la cuisinière
- ENTRETIEN ET REPARATION DE LA CUISINIERE
- Nettoyage général
- Programme de nettoyage
- INSTRUCTIONS D'INSTALLATION
- EXIGENCE
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en gaz
- INSTALLATION
- Déballage de la cuisinière
- Installation de la bride antibasculement
- Raccordement au gaz
- Vérifier que la bride antibasculement est bien installée et engagée
- Réglage de l’aplomb de la cuisinière
- Système d’allumage électronique
- Tiroir-réchaud ou tiroir de remisage de qualité supérieure (sur certains modèles)
- Tiroir de remisage (sur certains modèles)
- Porte du four
- Achever l’installation
- CONVERSIONS POUR CHANGEMENT DE GAZ
- Conversion pour l’alimentation au propane
- Conversion pour l’alimentation au gaz naturel
- Déplacement de la cuisinière
23
4. Turn gas pressure regulator cap counterclockwise with a 5/8"
(1.6 cm) combination wrench to remove.
NOTE: Do not remove the spring beneath the cap.
A. Plastic cover
B. Gas pressure regulator cap with hollow end
facing out
C. Gas pressure regulator cap with solid end
facing out
D. Washer
E. Gas pressure regulator cap
5. Turn over the gas pressure regulator cap and reinstall on
regulator so that the solid end faces out and the marking
“↓NG” is facing the direction shown in the above drawing.
6. Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Propane Gas to
Natural Gas)
1. Remove burner cap.
2. Remove the burner base.
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter electrode
E. Gas tube opening
3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and remove
by turning it counterclockwise and lifting out. Set gas orifice
spud aside.
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
4. Gas orifice spuds are stamped with a number on the side.
Replace the propane gas orifice spud with the correct Natural
gas orifice spud.
A. Stamped number
Refer to the following chart for the correct Natural gas orifice spud
placement.
Natural Gas Orifice Spud Chart
Burner Rating Size (mm) ID Number
18,000 BTU 2.00 200AM
17,000 BTU 1.96 196AM
15,000 BTU 1.80 180AM
9,500 BTU 1.40 140AM
8,000 BTU 1.30 130AM
5,000 BTU 1.00 100AM
NOTE: Refer to the model/serial/rating plate located on the oven
frame behind the top right-hand side of the oven door for proper
sizing of spuds for each burner location.
5. Place propane gas orifice spuds in the orifice spud bag.
IMPORTANT: Keep the propane gas orifice spuds in case of
reinstallation with propane gas.
6. Replace the burner base using both screws.
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.