COMMERCIAL TOP LOAD WASHER INSTALLATION, USER & SET-UP INSTRUCTIONS MODELS: MAT12CS, MAT12PD, MAT13MN, MAT13PN LEAVE THESE INSTRUCTIONS WITH THE OWNER MAYTAG COMPANY, NEWTON, IOWA 50208 2207647
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, explosion, electric shock, property damage or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using the appliance. It is for use only in washing, rinsing and spin drying household textiles and garments. 2. As with any equipment using electricity and having moving parts, there are potential hazards.
16. Unplug power supply cord when not in use, before cleaning or carrying out any owner maintenance tasks on your clothes washer. 17. Do not repair or replace any part of the appliance or attempt any servicing. Repairs and servicing should only be carried out by qualified service personnel. 18. Before the appliance is removed from service or discarded, remove the lid to the wash tub.
PARTS supplied for installation: 4 washers and 2 screens for water hoses Cable tie to secure drain hose to standpipe, inlet hose or laundry tub Beaded tie to secure drain hose to cabinet (if required) Locking cam STEP 1 PREPARE WASHER 1. Remove tape on lid. Remove accessory package from tub. 2. Tip the washer backward. Loosen front leveling leg lock nuts. 3. Tip washer slightly forward. Loosen rear leveling leg lock nuts. 4. REMOVE THE TUB BLOCK. 5. Remove the inlet hoses.
If the supply cord is damaged, it must be replaced with a specially terminated cord by an authorized service agent or a similarly qualified person in order to avoid a hazard. Do not connect via a cord extension set or electrical portable outlet device. HOSE CONNECTION 1. Never reuse old hose sets. Insert the rubber hose washer from accessory package into the SAE threaded end of the inlet hose. The SAE threaded end is pointed to by the flow arrow on the hoses.
SIPHON BREAK INSTALLATION If a 91 cm (36 in.) minimum standpipe is not available, or for floor drain installation and in cases where a tight connection is made between the drain hose and drain (standpipe, etc.) the 12001586 siphon break accessory is required. To install siphon break: 1. Cut the corrugated drain hose at the center of the larger straight section position B. Mounting Clamp 2. Position a hose clamp onto the cut end of the drain hose leading to the machine pump.
STEP 3 SETUP WASHER After the washer has been properly installed there are still a few steps required before the washer is ready for operation. Make the following revisions: CS MODELS (COIN SLIDE) These models are activated by coin slide in the control center. Install the coin slide (NOT provided with the product) as follows: First, remove coin slide actuator from accessory package that is found in the back of the coin vault. Two (2) screws from the package attach the actuator bracket to the coin slide.
GENERAL USER INFORMATION- PD & PN models BLANK DISPLAY – This condition indicates the appliance is inoperative. Enter set-up mode to view diagnostic code. “0 MINUTES” SHOWING IN DISPLAY – This condition indicates the appliance cannot be operated. Coins dropped during this condition will be stored in escrow but cannot be used until normal operation is restored by opening and closing the lid.
HOW TO USE THE KEY PADS TO PROGRAM THE CONTROLS 1. The LOWER LEFT key pad is used to adjust the values associated with set-up codes. Pressing the key pad will increment the value. Rapid adjustment is possible by holding the key pad down. 2. The LOWER MIDDLE key pad will advance you through the set-up codes. Pressing the key pad will advance you to the next available set-up code. Holding the key pad down will automatically advance through the set-up codes at a rate of one (1) per second. 3.
1.00 1. 00 0C MONEY COUNTER OPTION This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’. Not Selected ‘OFF’. Selected ‘ON’. Press the LOWER RIGHT key pad 3 consecutive times to select ‘ON’ and 3 consecutive times to remove (Not Selected ‘OFF’.) Counter resets by going from ‘OFF’ to ‘ON’. Press the LOWER MIDDLE key pad once to advance to next code or permanently select money count option by the following procedure. 2.00 C0 Selected ‘ON’ and not able to be deselected.
A.00 A. 00 SC VAULT VIEWING OPTION This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’. Not Selected ‘OFF’. Selected ‘ON’. Press the LOWER RIGHT key pad once for this selection. When selected, the money and/or cycle counts will be viewable (if counting is selected), when the coin box is removed. Press the LOWER MIDDLE key pad once to advance to next code. b.05 b. 05 VALUE OF COIN 1. This represents the value of coin 1 in number of coin units. (See NOTE ON COIN UNITS.) 5 x coin unit = 0.25.
J.Cd J. Cd C_ _d COIN OPTION Coin selected. Coins selected. Coins disabled. Press the LOWER RIGHT key pad 3 consecutive times for this selection. PN MODELS ONLY: Must be set for _d. Press the LOWER MIDDLE key pad once to advance to next code. L.00 L. 00 PS PRICE SUPPRESSION OPTION This option causes the customer display to show ‘ADD’ or ‘AVAILABLE’ rather than the amount of money to add. Not Selected ‘OFF’. Selected ‘ON’. Press the LOWER RIGHT key pad once for this selection.
DIAGNOSTIC CODES If the set-up mode is entered and one of the following has occurred, the appropriate diagnostic code will be in the display. d1 Water level detection error on control board or due to power line interference (cycles and customer display disabled until diagnostic code is manually cleared). d3 Water temperature sense error when equipped with temperature sensing water valve (cycles will fill with unregulated default water temperatures while the error persists).
TOP LOAD WASHER HELP MODE This mode is entered by pressing the LOWER LEFT key pad while in special pricing option mode 2.XX (or while dAS displays if operating with Maytag Data Acquisition setup). In help mode, the LOWER MIDDLE keypad can be used to advance through three help codes (displayed as 1h.XX, 2h.XX and 3h.XX). Pressing the LOWER RIGHT keypad while any of the help codes are displayed clears the help codes. The help modes are followed by the Energy Saving indication screen (displayed as hE.
INSTALLATION ACCESSORY KITS Part No. Description Application 12001875 Earthing Kit Additional external earth bonding kit. 12001585 Drain Hose Extension Extends drain hose for drain facilities higher than 1.2 m (4 ft.) 12001586 Siphon Break Used when an air-tight connection exists between drain hose and drain facility or for floor drain facilities. 12001599 Small Diameter Standpipe Drain Hose Used when standpipe diameter is too small to receive end of drain hose.
