MDG78PN Multiload Dryer Microprocessor User’s Manual Phase 8.3 Rev 2.2 Non-Coin / Coin Retain These Instructions In A Safe Place For Future Reference Maytag Benton Harbor, MI 1-800-662-3587 Part No.
IMPORTANT: For installation and use, please refer to the installation manual. Read all instructions before operating! State of California Proposition 65 Warnings: WARNING: This product contains a chemical known to the State of California to cause cancer. WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
General User Information Non-Coin Models “OPL Dry Mode” ____ Cold Start (Initial/First Use) ! ! This appliance has 20 preset cycles, which are ready for use. To start the unit, use the UP ( ) and DOWN ( ) ARROW keys to scroll through the preset cycles, until the desired cycle is highlighted, then press the START/ENTER ! ) key. A detailed description of the preset cycles is on a (! chart on page 8.
How to use the Keypad to Program Controls ! Non-Coin (OPL) Controllers The UP ARROW ( ) is used to increase numbers and scan through menu locations. ! The DOWN ARROW ( ) is used to decrease numbers and scan through menu locations. The START/ENTER (! ! ) key will enter program locations and save changes made. To back out of a menu location hit the STOP/PAUSE (X) key.
Quick Reference Programming Menu for Non-Coin (OPL) Models ______________ Machine Info Software Rev Program Setup Control Settings KEY FUNCTIONS Language Multi Language (Language 1, Language 2) Temp Scale (ºF, ºC) Buzzer Settings (End of Cycle, Beep Count) Backlight (0-200) ! DOWN ARROW ( ) ! Scroll down/decrease value UP ARROW ( ) Scroll up/increase value ENTER (! ) Accept selection PAUSE / STOP (X) Back out of a location Machine Settings Lint Cleaning Frequency (0-3 Hours) Axial Max Temp (10
Quick Reference Programming Menu for Coin/Debit/Free Models ______________ Machine Info Software Rev Program Setup Dry Mode Coin Dry Mode Free Dry Mode Control Settings KEY FUNCTIONS LOW Scroll down/decrease value HIGH Scroll up/increase value MEDIUM Accept selection PAUSE / STOP Back out of a location Language Multi Language (Language 1, Language 2) Temp Scale (ºF, ºC) Buzzer Settings (End of Cycle, Beep Count) Back Light (0-200) Ready Prompt (To start insert #, Ready, Custom) Machine Settings Li
! Choosing Cycle to Program ! At the “SELECT CYCLE” message, use the UP ( ) and DOWN ( ) ARROW keys to select the cycle that you would like to change. Note There is no need to enter spaces in any of the remaining character spaces. Once the " is selected, all remaining characters will become spaces.
Non-Coin (OPL) Factory Preset Programs/Parameters __________________________ The following are the default cycle descriptions: Cycle Name Cycle Type Dryness Cool Down Time Level Temp Auto / Manual Manual Only Auto Only 100º F - 160º F 38º C - 71º C 2-99 min. 70º F - 100º F 21º C - 38º C Time Reversing (Manual Only) Temp Mode Spin Stop Off / On 120-240 sec. 5-10 sec.
Each menu in Service Mode will contain a list of selectable items. The use of the HI or UP ARROW ( ) key and the LOW or DOWN ARROW ( ) key on the keypad will enable the currently selected item to change. The currently selected menu item will appear with a box around it. ! 2: TEMP SCALE – will display temperatures as degrees Fahrenheit or Celsius.
5: REVERSING MODE (feature is only available if model OFF / ON is set to reversing) 5. CLEAR COIN VAULT NO / YES 4: MED KEY SETTINGS (used on coin/debit only) 6. LEFT COIN VALUE .25 (adjustable between 1 - 2500) 1: TIME FOR AMOUNT TO START 10 (adjustable from 1 - 99 minutes) 7. RIGHT COIN VALUE .10 (adjustable between 1 - 2500) 2: TIME FOR TOP OFF 10 (adjustable from 1 - 99 minutes) 8. AMOUNT TO START (adjustable between 1 - 2500) .25 3: DRY TEMP 130 (100° - 160° F / 38° - 71° C) 9.
2: DIAGNOSTIC CYCLE The table below shows the standard features available and the feature symbol they correlate with. Diagnostic Mode enables the user to run the dryer and access items to troubleshoot a problem with the dryer. FEATURE SYMBOL When the diagnostic menu is first selected, the controls will prompt the user to start one of the defined cycles. FEATURE TEXT FEATURE EXH EXHAUST TEMP PROBE Exhaust Temperature Probe FEATURE INFORMATION (in Deg.
Faults _________________________________ Gen 2 Card Reader Communication Fault An exhaust probe fault occurs when the control detects that the exhaust temperature transducer is reading a temperature that is out of the probe’s normal operating temperature range for more than 3-seconds. There is an automatic fault clearing feature for this fault. If the fault condition no longer exists, the control will clear the fault condition and return to READY Mode.
