MAV (ATLANTIS) WASHER INSTALLATION INSTRUCTIONS
i SECTION 1. GENERAL INFORMATION WASHER PRE-INSTALLATION REQUIREMENTS NOTE: Proper installation sibility of the purchaser, • Do not store or operate washer in tern peratures below freezing. This can ¢aus_ damage to the pump, hoses and othe is the respon- components. (See page 1-5 for long ten storage.) Checkpoints for proper installation: Water pressure of 20 - 120 P.S.I.is require to fill the washer in the appropriate tim frame. Pressuresof less than 20 P.S.I.
grounding will reduce the risk of electrical shock by providing a path of least resistance for electrical current, The washer is equipped with a power supply cord which has a grounding conductor and three-prong grounding plug. For proper grounding, the threeprong grounding plug must be plugged into an appropriate three-prong grounded receptacle or outlet (see the following figure).
mately two (2) feet away. Carefully lay the washer on its back on top of INSTALLATION NOTE: Proper installation is the respon sibility of the purchaser. the corner posts, DO NOTLOWER OR RAISE THE WASHER B Y THE CONTROL PANEL. 4 Remove the crate bottom from the washer. Pop the plastic loose from the screw located between the back feet, or remove the screw entirely with a screwdriver. (Figure 1-2) Pull the plastic base away from the back feet.
(Back Of Control Console) _'_.. _'_., i Beaded Tie Clip (Rear Wall of Cabinet _l _ Figure 1-4 Figure 1-3 7. Pull the drain hose up vertically and snap the hose into the retaining clip positioned on the upper rear cabinet wall. (Figure 14) / 8. Install gooseneck end of drain hose into drain standpipe. Be sure the connection is not airtight between the drain hose and the standpipe. Standpipe must be at least 36" high.
14. Secure the drain hose to the standptpe or drain facility with the cable strap provided. This will ensure the drain hose will not fall out of the drain facility. (Figure 1- TOP VIEW OF WASHER 15. Connect inlet hoses to water supply using screenwashers at faucet connections, with the domed screen facing the faucet. (Figure 1-7) Tighten hose connections by hand until snug. Then, turnanother 2/3 of a turn with the pliers.
• Turn off hot and cold water faucets. • Disconnect both water inlet hoses at the faucets. Lower them to the floor. • With the service cord connected to the electrical outlet, rotate the timer to the normal start or fill position and pull timer knob to start washer. Turn water temperature selector switch to warm. • When water stops draining from the hoses, disconnect service cord. • Lower the drain hose to the floor and allow it to drain into a floor drain or shallow pan.
SPECIFICATIONS - WASHER (Lower Half Section) 71.8cm _" _ 363/8"1 8_.4 _n ° T " 68.6em I h102err ° CN ' CAPACITY 3.2 Cubic Feet ELECTRICAL 120 Volts, 60 Hz; Requires 15 amp circuit breaker or fused electrical supply. Power cord must be connected to a properly grounded and polarized outlet, MOTOR 1/2 H.P., reversible,2 Speed, 115 volt, 60 cycle A.C. POWER USAGE Motor Input: During Agitation* - 480 Watts Max (Fast)370 Watts Max. (Slov During Pump Out* - 760 Watts (Fast) 510 Watts Max.
Setting Gallons *Depth Inches Mini 10.5 6" 3 1/2" Medium 14.1 8 1/2" 5" High 19,5 11" 7" 13 1/2" 9 1/4" Super 23.3 *Allowable variations are plus or minus 1/2 inch. AGITATOR I SPEED Regular Cycle Slow (Delicate) Cycle SPIN *Basket Perforations 88 Oscillations per minute 57 Oscillations per minute ! i 155 DegreeArc 155 DegreeArc SPEED Regular Cycle Slow (Fine Wash) Cycle 620 R.P.M. 410 R.P.M. TABLE 1-1. AMPERAGE CHART WATER LEVEL Agitate-Regular Full Tub 10.
