Technical information

Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
June 2006 16027174
©2006 Maytag Services RPL 16023431
7
IN
Selection
Function
Display
Rotary Cycle Selector
Set To Normal
Press Start Pause
Lock State
UL LO or
Rotary Cycle Selector
Set To Wrinkle Control
Press Start Pause
High Water
Level
Rotary Cycle Selector
Set To Colors
Press Start Pause
Low Water
Level
Rotary Cycle Selector
Set To Hand Wash
Press Start Pause
*Tub Balance
Press Delay Start
Water
Temperature
Degrees F
Rotary Cycle Selector
Set To Delicates
Press Start Pause
Water
Temperature
Degrees C
Rotary Cycle Selector
Set To Heavy Duty
Press Start Pause
Main Relay
Selection
Component
Function
Off To On
or
On To Off
Rotary Cycle Selector
Set To Normal
Press Start Pause
Hot Water
Valve
Rotary Cycle Selector
Set To Wrinkle Control
Press Start Pause
Cold Water
Valve
Rotary Cycle Selector
Set To Delicates
Press Start Pause
Bleach Valve
Rotary Cycle Selector
Set To Quick Wash
Press Start Pause
Drain Pump
Motor
Door Lock
1 Attempt To Unlock
Valve On
2nd Press
Valve Off
Valve On
2nd Press
Valve Off
Valve On
2nd Press
Valve Off
Pump On
2nd Press
Pump Off
Press Delay Start
Motor On
2nd Press
Motor Off
*
Press Chime
Door Lock Lock Door
Press Temperature
Bleach Valve
and
Cold Water Valve
Extra Rinse
Fabric Softener Fill
2nd Press Valves Off
Board Input Test
While in Service Mode, pressing the
Temperature key will begin the Board
Input Test. This test turns ‘ON’ a specified
output after a key press. Pressing the
Temperature key again cancels the test. (Display
shows in).
While in Service Mode follow chart to check respective
function.
* ”U0” will be displayed during the time when the
machine is correcting for the unbalance; e.g. slowing
down to redistribute the load or to get to a lower spin
speed. Once the situation has been corrected (i.e. the
load has begun tumbling or the lower speed has
resulted in an acceptable amount of unbalance) ”U0”
will be displayed again.
Board Output Test
While in Service Mode, pressing the
Temperature and Extra Rinse key will
begin the Board Output Test. This test turns ‘ON’ a
specified output after a key press. (Pressing the
Temperature and Extra Rinse key again cancels the
test.) Only one output can be ‘ON’ at any time. All
outputs will be turned ‘OFF’ after five (5) minutes of
inactivity.
While in Service Mode follow chart to check respective
function.
*Note: Function may not occur for up to 20 seconds.
The “Delay Start” LED is ‘ON’. When activated,
the machine will tumble for 5 seconds in the CW
direction, pause for 2 seconds, tumble in the
CCW direction for 5 seconds, pause for 2
seconds; repeating this pattern until the Delay
Start button is pressed again. All tumble speeds
are 45 rpm.
Display Diagnostic Codes
The diagnostic code display can be
toggled ‘ON’ and ‘OFF’ from Service
Mode by pressing the Chime key and
rotating the cycle select knob. The
display will show a “d”.
Rotating the Cycle Selector knob in either direction will
cycle through the list of codes one code at a time with
no wrap. Once an initial direction is selected by the user
(either Clockwise or Counterclockwise), subsequent
movements of the knob in the same direction will show
older codes. If the user changes direction and turns the
knob in the opposite direction, the more recent code will
be displayed. If rotation is continued to the limits of the