240 EdwardsStreet, SE C]eve[and,Tennessee37311 Tei:423-472-3333 Fax:423-478-6710 STACKED WASHER- INSTALLATION IMPORTANT DRYER INSTRUCTIONS TO INSTALLER REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS AND COMBINATION WASHER/DRYERS TO AVOID THE DANGER OF A CHILD SUFFOCATING SHOULD HE/SHE CRAWL INSIDE AND THE DOOR BE SHUT. TIIE DRYER MUST NOT BE INSTALLED OR STORED WILL BE EXPOSED TO WATER ANI)/OR WEATHER. IN AN AREA WHERE IT US MODELS PLEASE READ THE FOLLOWING 1FNSTRUCTIONS CAREI_q.
C_s_omer Se_i_0 __ 240 EdwardsStreet,SE Cleveland,Tennessee3731; Te!: 423-472-3333 Fax:423-478-6710 IMPORTANT TO OWNER Retain these instructions for future reference. This new Maytag appliance is designed to serve you dependably for many years. However, it cannot do so unless provided with sufficient electrica! power, suitable exhausting and if a gas model, adequate gas supply. We urge you to read this carefully to make sure all requirements are met.
2a8 EdwardsStreet.SE Cleveland,Tennessee37311 Tel: 423472-3333 Fax:423-478-6710 \ Untape and open washer lid. Remove installation accessory package, fill hoses and drain hose and close lid. Leave tub block in place until installation is complete. Be sure to remove tub block after installation is complete and before use.! Using the carton corner posts stacked in pairs, lay the washer on the posts on the left side. Remove the crate base wires from the carton base.
_ustomer ..... o i ,,Jl :_1"_jl,,,_ml, 4TA_,,i.,ir" _ 2aOEdwardsS_e:. SE Cleveland,Tennessee37311 Tei:423-_72-3332 Fax:_23-_78-87i0 PREINSTALLATION CONSIDERATIONS Location: The stacked washer/dryer is approved for zero clearance installation on the sides and the back (depending on venting used). The location selected must take into consideration the dimensions of the unit and convenience for customer use and access in case service should be needed.
_x igOUllqj 24GEdwardsStreet, SE Cleve!and,Tennessee373!; Tei: 423472-3333 Fax:423-47g-67t0 KEY Air FACTS Flow: Exhaust: ductwork. Dryer 180 cubic feet per minute. 4 inch (t0.2 cm) duct permits a maximum of 50 feet (15.4 m) rigid aluminum Subtract 8 feet (2.44 m) for each 90 degree elbow and 8 feet for an exhaust hood. vented Motor: !/4 Export Model Heat - DRYER Source: out of the back. H.P.
240 EdwardsStreet,SE C!eveland,Tenressee37311 TeJ:423-472-3333 Fax:422-478-67!0 ALCOVE OR CLOSET INSTALLATION When the stacked washer/dryer is to be installed in an alcove area or a closet, clearance should be provided around the unit for an adequate air supply and for ease of installation and servicing. An appliance installed in a closet shall have no other fuel burning appliance installed in the same closet, such as gas furnace, water heater or space heater, etc.
240 EdwardsStreet,SE C[eveland,Tennes.-_ee .!7311 Tel:422-472-33._ Fax:423-478-57_0 MAKE - UP AIR For proper operation of the dryer unit, it is important to make sure the location has adequate make-up air. This is especially important in any confined area such as a bathroom or closet. There must be at least two 36 inch square unobstructed openings for intake air. This can be a louvered door or other equivalent opening.
240EdwardsS:raet,S£ Cleveland,Tensessee37_11 TeI: 423-472-$333 Fax:423-478-67"3 EXHAUSTING The free air flow rate is approximately 180 cubic feet per minute. The vent system carries lint and moisture away and to the outside. The length of the venting and the number of elbows affect the air flow rate and the efficiency of the exhaust system. DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE OR A CONCEALED SPACE OF A BUILDING, VENT CONNECTION, GAS VENT OR CHIMNEY.
2_0 EdwardsStreet SE Cieveiand.Tennessee57311 Tel: -:23-472-L333 Fax:423-478-6710 DIRECT EXHAUST An exhaust hood positioned to line up with the dryer exhaust pipe can be installed directly through an outside wall. This would be the shortest and most direct exhaust method. To exhaust up, route standard 4" diameter ducting up the recess and in the cabinet back using the furnished retaining strap an screws to get nearly flush to walt installation.
240 EdwardsStreet, SE C;eve!and,Tennessee373tl Te_:422-472-3333 Fax:423-478-67t0 RIGID DUCTWORK LIMITATIONS Rigid metal ductwork should not exceed 50' of straight 4" duct. Each 90 degree elbow and the exhaust hood should be considered equivalent to 8' of straight ductwork. For example, if an duct allowed would rigid ductwork run between 90 degree exhaust hood and two 90 degree elbows are used, the maximum straight be 26'. Not more than three 90 degree elbows should be used in any with an exhaust hood.
240 EdwardsStreet,SE Cleveland,7e"nessee37311 Tel: 423-472-$333 Fax:423-478-,3710 ELECTRICAL OBSERVE ALL NATIONAL ELECTRICAL REQUIREMENTS ELECTRICAL AND ORDINANCES CODES, SERVICE - 120 VOLTS, WASHER-GAS DRYER LOCAL CODES 60 HZ ONLY A 120 volt, 60 Hz, 15 ampere fused eIectrical supply is required. An individual branch (or separate) circuit serving only this appliance is recommended.
240 EdwarusStree[,SE Ueve]and,Tennessee37311 feF: _23-472-3333 Fax:423-_78-67_0 GROUNDING INSTRUCTIONS i F This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug.
240 EdwardsStreet.SE CJeveiand,Tennessee37311 Tel:423-472-3333 Fax:423-478-5710 ELECTRIC DRYER GROUNDING UNITS INSTRUCTIONS This electric dryer must be connected to a ground metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal on the back panel. Electric models are shipped with a ground strap connected from the neutral (P2) terminal block post to the frame of the dryer.
240 EdwardsStreet,SE Cleveiand,Tennessee37311 Tek 423472-3333 Fax:423-478-8710 G.F.I. If the electric dryer is protected by a GROUND cedure for a 4-wire hookup below. 4-WIRE FAULT INTERRUPTER, follow the pro- RECEPTACLE The frame of a 120/240 Volt machine must NOT be connected to neutral terminals. It MUST be connected to the 4th wire (green of the power supply) or to the metallic covering of a three-wire supply.
240Edwards Street.SE Cleveland,Tennessee37311 Tei:423-z72-3333 Fax:423-478-67"0 4-WIRE SYSTEM 1. Remove CONNECTIONS the terminal block cover. 2. Remove the ground strap from the ground screw and center (silver colored) terminal of the terminal block. 3. Connect the neutral (white) wire of the power supply cord to the center (silver colored) terminal of the terminal block. Connect the grounding (green) wire of the cord to the external ground connector, sing the green screw. 4.
240EdwardsStreet,SE CIeveian&Te£_essBe;7311 1el: 423-472-,3333 Fax:423-478-6710 WATER SUPPLY WATER SUPPLY AND DRAIN The water supply to the washer unit should be capable of providing both adequate water pressure and water temperature. The pressure should fall within the range of 30 pounds per square inch to 120 pounds per square inch when the washer is filling. Note that this is flow pressure and not static pressure.
240 EdwardsStreet, SE Cleveiand,TennesseeZ7311 Tel:423-472-3333 Fax:423-478-6710 Models are available that incorporate water supply, water drain, 120 Volt AC and 240 Volt AC connections. An example is shown. O © O \ If the faucets and!or drain is located to either side of the stacked washer/dryer, openings located in the dryer stand uprights to allow hoses and power cords to be passed through. This is to allow installation against the back wall. (This is dependent on venting used.) [] _'_-vfr,',.
240EdwardsStreet, SE Creveianct,Tennessee37311 Tel: 423-47"2-3333 Fax:423-478-6710 GAS CONNECTION Gas operated dryers are equipped with a burner orifice for operation on NATURAL gas. If the dryer is to be operated on LP gas, it must be converted correctly for safety and proper performance. Conversion kits from NATURAL to LPG or LPG to NATURAL are available through your local Maytag dealer.
CustomerSe_ic_ _'__ 240 EGwardsStreet, SE Cleveland,Tennessee3731; Tel: :t23-472-3333 Fax:_23-478-67t0 Turn on gas supply and open the shutoff at the gas valve. Check all gas connections for leaks using a soap solution. If bubbles occur, tighten connections and recheck. DO NOT use an open flame to check for gas leaks. NOTE: As a courtesy, many local gas utilities will inspect a gas appliance Check with your utility to see if this service is provided in your area. installation.
240 EdwardsStreet,SE Cleveland.Tennessee37311 Te!:423-472-3333 Fax:423-478-6710 INSTALLATION INSTALL DRYER UNIT AND STAND The dryer and stand are installed first. With the connections prepared for exhausting, electric power and gas (if gas stacked washer/dryer, see Gas Connection), the dryer and stand are moved to the location. NOTE: When moving the dryer and stand on an appliance hand truck, it is recommended that the dryer and stand be Backed upside down.
240 EdwardsStreet, SE Cleveland,Tennessee37311 Tel:423-472-,3333 Fax:423-478-67;0 INSTALL FILL HOSES Insert plain hose washers in 90 degree end of fill hoses and screen washers hoses. The screens should point outward. The valve inlets are marked in straight end of '_H" and "C" to denote the hot inlet (top) and cold inlet (lower). Connect 90 degree ends of hoses to the valve. Connect lower hose first. Be sure that hose connectors are not cross threaded on the valve.
_0st0_er S_ice _A4'Y"/,4G 240 EdwardsStreet, SE Cleveland.Tennessee3731t Tel: 423-472-3333 Fax:423-478-67;0 INSTALL DRAIN HOSE Secure drain hose to siphon break using the hose clamp provided in the parts package. The siphon break can be turned right or left to meet the end of the drain hose. Place the gooseneck into the standpipe (or position the gooseneck as if it were in the standpipe).
240EdwardsStreet,SE Cleveland,Tennessee37311 Te_:423-472-3333 Fax:423-478-6710 If not previously done, remove shipping pads from washer top. Move the washer into position in front of the dryer and stand. Use caution to avoid floor damage because of the minimum height of the rear legs. Tip forward enough for glides to clear the legs of the stand, and guide the glides into the slots on the top of the stand legs. Lower Washer Glide Bar Down into slot.
0 EdwardsStreet,SE Cleveland.Tennessee3731 Tel: 423-472-3333 Fax:422-478-6710 If the unit is a microprocessor 120 volt AC outlet. stacked washer/dryer, connect the washer power cord to the Slide washer back into position. A peg on the back right corner of the washer wilt locate in a socket on the fight leg of the dryer stand. Adjust the washer front legs down against the floor to raise the washer front slightly.
240 EdwardsStreet,SE C;eve{end,Tennessee37311 Tek 422-472-33,g3 Fax:423-478-67:0 FINISH All the cabinet and external finishes are protected against rust to keep product looking well for many years. Cleaning and waxing will provide additional protection to these finishes. The washer top has a porcelain finish. Since porcelain is "glass" bonded to metal, it is very durable. Avoid damage from sharp blows of objects or tools used around and in the appliance. Clean the control panel with a soft damp cloth.
A,tt4Y'TAG 240 EdwardsStreet, SE Cleve]an&Tennessee37311 Tel: 423-472-3333 Fax:423-478-67;8 INSTALLATION ACCESSOR S 059129 Vent hood - 4" (10.16 cm) opening 059130 Aluminum pipe - 4" x 24:(10.16 059131 Aluminum elbow - 4" (10.16 cm) 059134 Aluminum window plate - 15" x 20" (38.10 cm x 50.80 cm) - 4" (10.16 cm) hole 059143 Flexible vent kit - contains wide opening vent hood, wall plate, two clamps and flexible aluminum vent duct 304353 Flexible aluminum vent duct - 4" (10.
