User guide

ManualsBrandsMayline ManualsFurniture6' Adder for Conference Table

BETTER FOR YOUR BUSINESS

When ordering components, specific color and/or size information may be required.

Contact a Mayline Customer Service Representative. 1-800-822-8037

NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.

COMPONENTS:

Item # QTY. DESCRIPTION PART #

1 1 ADDER LEG A8046**

2 2 SPREADER B8376**

3 1 TROUGH ASSEMBLY A8103**

4 1 WORKSURFACE TACT6A**

5 4 OUTSIDE ACCESS PANEL B8378**

HARDWARE BAG (PART No. A8123) * for individual item, order that part number

Item # QTY DESCRIPTION PART #

E1 2 TUBE INSERT, 5/16-18 T139*

E2 2 GLIDE Q608*

E3 18 SCREWS #10-32 x 1/2" X204*

E4 32 SCREW #10 x 3/4 X11*

E5 2 SLAM LATCH Q643*

E6 12 SLAM LATCH Q624*

E7 4 FELT PAD E517*

E8 4 STAND OFF B8415*

E9 2 SCREW #6 x 1 X14*

ASSEMBLY INSTRUCTIONS

TRANSACTION 6' ADDER TABLE

Item # QTY. DESCRIPTION PART #

6 2 CENTER ACCESS PANEL B8311**

7 2 INNER LEG PANEL 11.79" B8411**

8 1 R.H. CONNECTOR PANEL B8312

9 1 L.H. CONNECTOR PANEL B8313

10 1 GROMMET F787BK

11 1 WIRE COVER F784G

** Denotes Color Code

(1)

Summary of content (4 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS TRANSACTION 6' ADDER TABLE NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. COMPONENTS: Item # 1 2 3 4 5 QTY. 1 2 1 1 4 When ordering components, specific color and/or size information may be required. Contact a Mayline Customer Service Representative. 1-800-822-8037 DESCRIPTION PART # ADDER LEG SPREADER TROUGH ASSEMBLY WORKSURFACE OUTSIDE ACCESS PANEL Item # A8046** B8376** A8103** TACT6A** B8378** 6 7 8 9 10 11 QTY.
PAGE 2
1. Install threaded inserts (E1) into Adder Leg (1). 2. Thread Glides (E2) into threaded inserts installed in Step 1. 3. Partially install Screws (E3) into the bottom hole on both sides of the Adder Leg (1) so that the screw heads are approximately 1/8" from the leg. 4. Using the key hole slots in the ends of the Trough Assembly (3), attach Trough Assembly to Adder Leg. Tighten two Screws holding trough.
PAGE 3
5. Assemble Starter Base per instructions included with that product. 6. Move assembled Adder Base into position. Using the key hole slots in Trough end (3), attach the Trough to the partially installed screws in the assembled Starter Base. Starter Base 7. Install two Spreaders (2) to Adder Leg (1) and to assembled Starter Base using Screws (E3). 8. TIGHTEN ALL SCREWS mounting Spreaders and Trough. 9.
PAGE 4
13. Position Starter Worksurface over Starter Base and loosely fasten in place using hardware and instructions supplied with that product. Position Adder Worksurface (4) on Adder base and loosely fasten using screws (E4) through legs, spreader and connector panels. 14. Continue the Conference Table assembly by installing another Adder worksurface or complete the Conference Table by installing the final worksurface. Once ALL tops are installed and aligned, tighten all screws. 15.