MAXXUS ® PRO SPK-23 FITNESS CYCLE OWNER’S MANUAL
Dear customer, Thank you for purchasing MAXXUS® Pro SPK-23 Fitness Cycle. This product was designed to meet your workout needs and provide you with a healthier life. Before you begin using this product, please read the Owner’s Manual completely and thoroughly and follow the instructions of all WARNING and CAUTION labels. If you have any questions about this product or are in need of replacement parts, please contact Customer Service by calling (909) 212-5555.
SAFETY INSTRUCTIONS Before you start to assemble and operate this product, please carefully read the Owner’s Manual in its entirety. Please follow all instructions in this Owner’s Manual as described. Be sure to read through the Safety Instructions below and keep this Owner’s Manual for future reference. ● Misuse of this product may cause serious injury. ● Consult your physician before starting any exercise program. Please follow your physician’s advice on fitness training.
PARTS LIST Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Description Main Frame Rear Foot Bar Front Foot Bar U-Zone Bar Seat Post Handle Post Seat Slider Handle Bar End Cap Adjustable Pad Move Wheel Hex Head Bolt Nylon Nut Washer Hex Head Bolt Cap Nut End Cap Bearing Bearing S Nut Belt Wheel Rod Left Cover Right Cover Spring Elbow Pad Support Rear Cover Front Left Cover Front Right Cover Screw Screw Screw Screw Tapping Screw Tapping Screw Flywheel B
EXPLODED DRAWING ____________________________________________________________ 4
PACKING PARTS LIST ____________________________________________________________ 5
ASSEMBLY ● Read the Owner’s Manual in its entirety before assembly. ● Remove all parts from the box. ● Check to confirm receipt of all parts and quantities shown in the Packing Parts List on page 5. (Note: Some parts may be pre-assembled.) STEP 2 Slide the Front Foot Bar (3) to the front of the Main Frame (1) adding two Washers (14), two Spring Washers (68), two Cap Nuts (16), and two Hex Head Bolts (15) as shown in Figure 1. ** Tighten all bolts used in STEP 2 with the two Spanner Tools (66) & (67).
ASSEMBLY STEP 4 Attach the Left Pedal (55) and Right Pedal (56) to the Left Crank (53) and Right Crank (54) as shown in Figure 2. ** Tighten the Left & Right Pedals used in STEP 4 with the Spanner Tool (67). STEP 5 Insert the Seat Post (5) into the tube of the Main Frame (1) with Knob (60) as shown in Figure 3. ** Hand tighten ONLY. STEP 6 Affix the Seat (62) on the bar of the Seat Slider (7).
ASSEMBLY STEP 7 Insert the Handle Post (6) into the tube of the Main Frame (1) with Knob (60) as shown in Figure 4. ** Hand tighten ONLY. STEP 8 There are two holes on either side of the Handle Bar (8) for Elbow Pad (70) adjustments. You can choose the hole which is suitable for you and tighten the Elbow Pad (70) onto the Handle Bar (8). First, insert the bolts on the underside of each Elbow Pad (70).
After assembling the bike and tightening all appropriate components as instructed, you can now begin using bike. Handle bar, seat, and elbow pad adjustments allow you to adjust the bike to fit your size and body frame. Seat with spring on the underside brings you comfort while riding. Streamline surface design of this bike fits in with ergonomics and increases comfort.
STEP 1 Slide the Tension Lever (#44) for resistance setting. There are 8 gears (1 through 8) of resistance. Gear 1 has the lowest level of resistance and gear 8 has the highest level of resistance. STEP 2 If you want the resistance to be less, then move the gear to the lowest level of resistance (gear 8), and slightly adjust the Shift Lever Wire (Pillar and Hexagon Screw) as seen below. (A) (B) Loosen Pillar (A) slightly to increase the resistance.
STEP 3 After Steps 1 and 2 and if the resistance is still needed to be decreased or increased, please follow the instruction below. (E) (C) (D) Press Spring (C), then U-shaped Plate (D) will become loose. Take off the U-shaped Plate (D). Loosen the Hexagon Screw (E) slightly to decrease the resistance. Put back the U-shaped Plate (D). ** The more loose the Hexagon Screw (E) is, the less resistance. ** The more tight the Hexagon Screw (E) is, the more resistance.
Before you proceed further with this step, please make sure you have completed the above Steps 1, 2, and 3. If bike still needs more resistance adjustment, then complete Step 4. Picture (F) Picture (G) Loosen the screw which is tightened on the black cap (as seen circled in blue in Picture (F)). Take off the screw and insert into the hole which is nearest the seat in Picture (G). Then tighten the screw to decrease the resistance. ** Original setting: The screw is tighten on the middle hole (b).
(Note: The label shown below is not of actual size.) ____________________________________________________________ WARRANTY This Limited Warranty applies in the United States to products distributed under the MAXXUS brand name. This warranty extends only to the original purchaser and stands at one (1) year from the date of purchase. This warranty is not transferable to anyone who subsequently purchases the product from the original purchaser.
