Operation Manual

Teileliste - Multipresse
Teil-Nr. Bezeichnung Menge Teil-Nr. Bezeichnung Menge
1 back ground frame link 1 57 bolts M10x65 2
2 right side frame 1 58 bolts M10x55 1
3 76 semi-circular plate 2 59 right sliding sleeve 1
4 bolts M10x95 10 60 left expansion arm 1
5 left side frame 1 61 right expansion arm 1
6 toprail 1 62 bolts M10x20 9
7 toprail link plate 2 63 feet pad 1
8 bolts M12x70 4 64 bolts M10x25 8
9 washer 8 65 M10 washer Ø25xØ10.5xT1.5 2
10 tip Ø12 5 66 tube cap Ø50 2
11 tube cap □50x70x2.0 2 67 bumper block 2
12 pulley Ø92 20 68 hand pad 2
13 insert nut M10 2 69 outer hexagon bolt M8x20 8
14 outer hexagon bolt M10x45 15 70 expansion arm spindle 2
15 double-headed bolt 2 71 flat pulley frame 1
16 76 tube cap 2 72 cable 1 L： 2.515mm 1
17 50100 oval tube cap 2 73 double pulley plate 1
18 32 powder metallurgy sleeve 6 74 cross pulley plate-roundshape
19 10 Powder metallurgy sleeve 12 75 cable 4 L： 3.100mm 1
20 hang lever shaft 24 76 cable 2 L： 3.590mm 1
21 barbell bar cap 24 77 cable 3 L： 10.215mm 1
22 outer hexagon bolt M10x45 7 78 9 section chain hoist hock
23 washer Ø10 89 79 barbell inside bar 1
24 hexagonsock M10x10 24 80 right horizontal bar 1
25 guide rod Ø25x1.850 2 81 left horizontal bar 1
26 right safty hook 1 82 right short safety stop 1
27 locknut M10 39 83 left short safety stop 1
28 weight stack bumper 4 84 Leg press adjusting bracket 1
29 guide rod lock set 2 85 Flat head bolt 2
30 high pull pulley 1 86 long safety stop 2
31 headless socket head bolts M8x10 8 87 barbell bar sleve tube
32 linear bearing LM25UU 6 88 barbell bar cap 2
33 circlip for hole Ø40 8 89 weight plate locating sleeve 2
34 locknut M12 4 90 washer on shaft Ø25 2
35 sliding sleeve left part 1 91 plum blossom knob M10 2
36 bearing 6006 4 92 tube cap Ø48 2
37 outer hexagon bolt M8x20 93 safety stop short rubber 85x45xT4 2
38 circlip for hole Ø55 4 94 countersunk head tapping screw ST4.0x12 20
39 left safty hook 1 95 sponge inside cap 2
40 handlebar grip Ø24.5x140 4 96 100 sponge 2
41 round tube cap Ø25x1.5 6 97 sponge outside cap 2
42 washer Ø8 12 98 hexagon socket button head screws M8x25 2
43 locknut M8 2 99 Round head plum flower pull pin 1
44 ring chrome 1 100 safty stop long rubber 387x45xT4.0 2
45 bumper Ø60xØ30x30 2 101 3000 back pad 1
46 back sliding sleeve 1 102 bolts M8x100 2
47 back guide rod nuts 1 103 barbell plate inside bar 6
48 back seat standing tube 1 104 barbell bar holder turning link tube 1
49 bolts M10x90 6 105 barbell bar holder 1
50 back top bar link 1 106 pivot pin axis 1
51 76semi-circular plate t3.0x59x140 2 107
powder metallurgy sleeve Ø50xØ25x15
2
52 back guide rod -without hole Ø25xt1.5x1840 1 108 rcushion collar 2
53 nylon sliding sleeve 4 109 bearing 6005 4
54 2“sleeve 8 110 low pull short bar 1
55 big pulley Ø127 1 111 low pull short bar handlebar grip 32x120 2
56 U shape supporting frame 2
1
1
2
4
25