Installation Guide

Installation Into Recessed Housing:
STEP1: Turn off the power before installation. Remove the existing
diffuser, bulb and trim as applicable.
STEP2: Screw E26 socket adapter into socket in housing. (Figure 1)
STEP3: Plug the connector of the retrofit kit into the connector of
the socket adapter assembly. (Figure 2)
STEP4: Use the CCT Selector Switch on the back of the fixture to
select the desired color of the light.
STEP5: Squeeze the torsion springs together and install into
torsion spring brackets inside the housing as shown. (Figure 3)
STEP6: Tuck all wires into the housing and carefully push the LED
trim until its outer edge is flush against the ceiling surface. (Figure 4)
CAUTIONS:
1. For your safety, read and understand instructions completely before starting installation.
2. Before
attempting Installation, check your local electric code, as it sets wiring standards for
your locality.
1. If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire
is connected to the switch. DO NOT connect the white supply wire to the switch.
2. Make sure no bare wires are exposed outside the wire nut connectors.
3. This lamp is not compatible with photo controls, occupancy sensors, or timing devices.
Electrical parameters:
Model
MRL-61405S
Input Voltage (V
)
120
Input W
attage (
W)
14
Three Year Warranty:
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free
from defects in material and/or workmanship only. Maxxima will replace any warranteed product to
the original consumer/purchaser if the product fails because of defects due to workmanship and/or
materials within the limited warranty period. Limited warranty is not transferable and applies to the
original installation of the Maxxima product. This offer does not constitute in any way a product
guarantee and Maxxima does not hereby assume any obilgation whatsoever beyond sending a free
replacement product.
NOTES:
Figure 1
Product Dimensions:
NOTE: Torsion springs are pre-installed for 6" housing compatibility. For use in 5" housing
move both springs to the inner position using a philips screwdriver.
Figure 2
Figure 3
Figure 4
3.45"
6.75"
2700K 3000K
3500K 4000K 5000K
CCT Selector Switch:
Located on the back of the fixture
5" & 6" LED Retrofit-Kit Installation Instructions
The units covered in these instructions are intended to retrofit Type IC or Type Non-IC luminaires.
WARNING / ATTENTION:
1. Risk of fire or electric shock. Installation of this retrofit kit requires a person familiar with the
construction and operation of the luminaire's electrical system and the hazard involved. If not
qualified, do not attempt installation. Contact a qualified electrician.
2. Risk of fire or electric shock. Install this kit only in luminaires that have the construction
features and dimensions shown in the photographs and/or drawings and where the input
rating of the retrofit kit does not exceed the input rating of the luminaire.
3. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or
other sharp objects.
4. Do not make or alter any open holes in an enclosure of wiring or electrical components
during kit installation.
5. THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE
APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT
SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.
[e-mail] 866-MAXXIMA (629-9462)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY
[e-mail] 866-MAXXIMA (629-9462)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY
Use only fixed luminaire with
minimum lamp compartment
dimensions 4" diameter x 5.5" depth