Installation Guide

Outdoor Ceiling Fixture Installation Instructions
1. Please read all warnings and instructions before installation.
2. The fixture must be wired in accordance with the National Electric
Code and applicable local codes or ordinances.
3. To insure personal safety, proper grounding is required.
WARNING:
1. To avoid fire, shock, or death, disconnect power at circuit breaker
or fuse before the installation.
2. If you are unsure about the installation or maintenance of the
Outdoor Ceiling Fixture, please consult a qualified electrician.
SAFETY:
1. This fixture should not be used in areas with limited ventilation or
high ambient temperature exceeding 45°C.
2. Fixture cannot be used with a dimmer switch, motion sensor and
other electronic switching devices.
INSTALLATION NOTES:
PRODUCT SPECIFICATION:
Part Number: MEL-9175W
Input Voltage: 120 VAC
Amp Draw: 0.11 A
Frequency: 60 Hz
Rated Power: 12.5W
Beam Angle: 120°
Suitable for: Damp Location
INSTALLATION LOCATION:
This fixture must only be wall-mounted. Be certain that the receiving
junction box is well secured and can support the weight of the lamp.
PRODUCT DIMENSIONS:
INSTALLATION INSTRUCTION:
CAUTION: Read WARNING and SAFETY Notes before beginning
installation.
MEL-9175W
www.maxximastyle.com
9.25”x9.25”
5.12”
1
6
7
8
9
5
10
11
12
1. Outlet Box (not included)
2. Outlet Box Mounting Screws (2 X)
3. Mounting Plate (1)
4. Fixture Mounting Screw (1)
5. Fixture Mounting Nut (1)
6. White Fixture
Wire
7. Black Fixture Wire
8. Fixture Ground Wire
9. Wire Nut (3 X)
10. Fixture Body
11. Fixture Housing (1)
12. Screws (2 X)
2
3
4
6.MOUNT FIXTURE HOUSING
Insert fixture body(10) screw bolt through fixture
housing (11)holes and secure the screws (12) to the ends
of the fixture body(10).
7.TURN POWER ON Turn power on at circuit breaker or replace the fuse.
1.TURN POWER OFF Turn power off at circuit breaker or remove fuse.
2.PREPARE CROSS BAR Screw in the Fixture Mounting Screws (4) into the
Mounting Plate (3)
3.MOUNT CROSS BAR
Mount Mounting Plate (3) to Outlet Box (1) by inserting
4.CONNECT FIXTURE
the two Mounting Screws (2) through slots in Mounting
Plate.
Hold the fixture body (10) close to the outlet box(1).
Using wire nuts provided connect Yellow/Green wire
from fixture to green or bare copper ground (house)
wire. If outlet box is grounded you may fasten fixture
ground wire directly to outlet box. Connect white fixture
wire(s) to neutral supply wire. Connect black fixture
wire(s) to power supply wire.
5.MOUNT FIXTURE BODY
Insert Fixture Mounting Screw (4) through holes on the
fixture body and secure to Mounting Plate by
tightening Fixture Mounting Nut (5). NOTE: Hand
tighten Mounting Nuts. Do not use any tools as over
tightening may occur causing damage to back plate.
[e-mail] 866-MAXXIMA (629-9462) www.maxximastyle.com 125 Cabot Court Hauppauge, NY 11788
3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.