Installation Guide
Table Of Contents
- ICE MAKER SAFETY
- IMPORTANT SAFEGUARDS
- TECHNICAL INFORMATION
- INTRODUCTION
- COMPONENT LOCATIONS
- ICE MAKER INSTALLATION
- INSTALLATION TYPES
- OPERATION
- MIM50P and MIM50P-O DRAIN SYSTEM OPERATION
- CLEANING AND MAINTENANCE
- CONTROL PANEL
- MAJOR FUNCTIONS
- TROUBLE SHOOTING
- SÉCURITÉ ET MACHINE À GLAÇONS
- MESURES DE PROTECTION IMPORTANTES
- RENSEIGNEMENTS TECHNIQUES
- INTRODUCTION
- EMPLACEMENTS DES COMPOSANTS
- INSTALLATION DE LA MACHINE À GLAÇONS
- Retirer le matériau d’emballage
- Nettoyage avant l’utilisation
- Dégagements pour l’installation
- Exigences en matière d’électricité
- Méthode recommandée de mise à la terre
- Mise de niveau de la machine à glaçons
- Inverser l’ouverture de porte pour MIM50-O et MIM50V
- Inverser l’ouverture de porte pour MIM50, MIM50P et MIM50P-O
- Alimentation en eau
- Outils requis
- Évacuation
- TYPES D’INSTALLATION
- UTILISATION
- FONCTIONNEMENT DU SYSTÈME D’ÉVACUATION MIM50P et MIM50P-O
- NETTOYAGE ET ENTRETIEN
- PANNEAU DE COMMANDE
- FONCTIONS IMPORTANTES
- DÉPANNAGE
- SEGURIDAD DE LA MÁQUINA DE HACER HIELO
- DISPOSICIONES DE SEGURIDAD IMPORTANTES
- INFORMACIÓN TÉCNICA
- INTRODUCCIÓN
- UBICACIONES DE COMPONENTES
- INSTALACIÓN DE LA MÁQUINA DE HACER HIELO
- Quitar los materiales de empaque
- Limpieza antes de usar
- Espacio de separación para la instalación
- Requisitos eléctricos
- Método recomendado de conexión a tierra
- Nivelar la máquina de hacer hielo
- Cómo cambiar el sentido en que abren las puertas de MIM50-O y MIM50V
- Cómo cambiar el sentido en que abren las puertas de MIM50, MIM50P y MIM50P-O
- Suministro de agua
- Herramientas necesarias
- Desagüe
- TIPOS DE INSTALACIÓN
- OPERACIÓN
- OPERACIÓN DEL SISTEMA DE DESAGÜE DE MIM50P Y MIM50P-O
- LIMPIEZA Y MANTENIMIENTO
- PANEL DE CONTROL
- FUNCIONES PRINCIPALES
- SOLUCIÓN DE PROBLEMAS
- Blank Page
- Blank Page
11/07/2017 PK
7
Reversing The Door Swing For MIM50-O and MIM50V
Tools needed: Flathead screwdriver, Phillips screwdriver
NOTE: Before you begin, unplug the ice maker or disconnect power.
To Remove Door From Hinges
1. Remove the top hinge cover.
2. Using a Phillips screwdriver, remove the screws, remove the top hinge mat and top hinge. Keep the parts
together and set them aside. (The MIM50V has a black hinge and no cover or mat, but is removed same
way as MIM50-O top hinge.)
3. Lift the door off of the bottom hinge and set the door aside.
To Replace Door On Hinges
1.
Using a flathead screwdriver, remove the plug buttons from the screw holes opposite the door hinges, top and
bottom. Set aside.
2.
Remove the front louver. Set aside.
3.
Remove the bottom hinge and place it on the opposite side at the bottom of the door. (The MIM50V bottom
hinge removed and installed same way as MIM50-O bottom hinge.)
4.
Position the door on the bottom hinge.
5.
Align the door on the bottom hinge and replace the top hinge and top hinge mat.
6.
Replace top hinge cover.
7.
Push the plug buttons into the original screw holes.
See Figure below:
Top hinge cover
Cabinet
Top hinge mat
Top hinge
Top hinge
Door
Bottom hinge
Bottom hinge
MIM50V black top hinge
no cover or mat.