Sivy SA-3340S Hardware User Manual Ultra 320 SCSI to Serial ATA Disk Array Systems Version 1.
ESC Enter SA-3340S Ultra 320 SCSI to Serial ATA Disk Array System Hardware User Manual
Table of Contents Preface................................................................................................................... i Chapter 1 Overview System Requirements ........................................................................................... 1 Operating Environment .................................................................................... 1 VT100 Terminal Settings .................................................................................. 1 Host Interface ..
Preface About this Manual This manual is designed to make the disk array system as easy to use as possible. Information contained in this document has been checked for accuracy, but no guarantee is given that the contents are correct. Information and specifications are subject to change without notice. Copyright Notice © Copyright 2006 MaxTronic International Co., Ltd. All rights reserved.
SA-3340S Serial ATA Disk Array Systems Important Safety Instructions, Care and Handling Preface – Before starting, take a few minutes to read this manual. Read all of these instructions and save this manual for later reference. Protect the disk array system from extremely high or low temperatures. Let the disk array system warm (or cool) to room temperature before using it. Important Safety Instructions, Care and Handling Protect the disk array system from being bumped or dropped.
SA-3340S Serial ATA Disk Array Systems The appliance must be grounded. The disk array system is equipped with a 3-wire grounded type of power cord. This power cord will only fit into a grounded type of power outlet. Never push any kind of object into the disk array system through cabinet gaps and openings, since they may touch dangerous voltage points and cause a risk of fire or electric shock. Unplug the power cord from the wall outlet before cleaning. Keep the disk array system dry.
SA-3340S Serial ATA Disk Array Systems Placement Notes Preface – Important Safety Instructions, Care and Handling • The disk array system LCD panel can be damaged by exposure to direct sunlight. Limit exposure to subdued or indirect sunlight only. • The disk array system should be used only in clean environments that are free from airborne contaminants such as dust, dirt, and smoke. Excessive moisture or oil particles in the air can also hinder disk array system performance.
1 Overview System Requirements Ensure that the following requirements are met before installing the disk array system. Operating Environment • • • • • 15 cm (6 inches) of space around the disk array system for proper ventilation ambient temperature of 5°C to 40°C (40°F to 104°F) ambient non-condensing relative humidity of 10% to 85% dust, smoke, and oil free environment no large magnetic fields, such as those generated by a high voltage power cables and motors, etc.
SA-3340S Serial ATA Disk Array Systems Host Interface The disk array system has dual SCSI interfaces interfaces. Refer to the following sections to understand host interface system requirements. 1 Overview – System Requirements Small Computer Systems Interface The SA-3340S has dual Ultra320 SCSI interfaces that are compatible with previous SCSI standards. Refer to the following table to understand SCSI bus requirements.
2 Basic Configuration This chapter describes disk array system connections and disk installation. Unpacking Contact your supplier if any of the following items are missing or damaged. Caution The disk array system is heavy. Be careful when lifting and moving it.
SA-3340S Serial ATA Disk Array Systems Components 2 Basic Configuration – Components Front View 9 1 2 3 4 5 6 7 8 No. 1-8 9 Name Description Disk trays 1 to 8 Removable hot swap disk trays. Control panel Displays warning, operating, and configuration information.
SA-3340S Serial ATA Disk Array Systems Control Panel 2 2 3 5 6 7 No. Name 8 Description 1 LCD panel Displays warning, operating, and configuration information. 2 Up button Moves up in the LCD menus. 3 Escape button Returns to the previous LCD menu without making changes. 4 Power-on indicator Indicates the disk array system power is on. 5 Power supply fail indicator Indicates a failed power supply.
SA-3340S Serial ATA Disk Array Systems Disk Tray 1 1 2 Top Basic Configuration – Components Left Right Front 4 5 2 3 No. Name Description 1 Disk mounting holes Allows the disk be mounted on the disk tray with the screws included with the disk. 2 Tray lock Prevents unauthorized removal of a disk tray. Opened with the included disk tray lock key. 3 Tray handle Releases the disk tray.
SA-3340S Serial ATA Disk Array Systems Rear View 2 1 Host Port 1 Host Port 2 3 8 9 10 11 4 5 12 6 7 No. Name 1 RS-232 Port Ethernet Port Host Port 1 (Primary SCSI channel) Power Supply 2 Hot Swap Power Supply Release Power Supply AC In Power Supply Handle Host Port 2 (Secondary SCSI channel) Fan 1 Fan 2 Power Supply Switch Power Supply 1 2 3 4 5 6 7 8 9 10 11 12 Description Connects to a VT100 terminal or equivalent. Used for browser-based configuration. Connects to the host server.
SA-3340S Serial ATA Disk Array Systems Installing Disks This section describes how to install disks in the disk array system. 2 Basic Configuration – Installing Disks 1 Unlock the disk tray (A) then pull the disk tray handle to the opened position (B) and remove the disk tray (C). ESC ESC Enter Enter B A C 2 Insert the disk into the disk tray. The disk should face up with the connectors directed toward the open rear of the tray. 3 Align the back of the disk with the back of the disk tray.
SA-3340S Serial ATA Disk Array Systems 4 Attach the disk to the disk tray with the screws supplied by the disk supplier. 2 ESC ESC Enter Enter A C B 6 Repeat these steps until all of the required disks have been installed. 9 Basic Configuration – Installing Disks 5 Slide the disk tray back into the empty slot (A), push the disk tray handle closed (B), then lock the disk tray (C).
SA-3340S Serial ATA Disk Array Systems Making Connections 2 After the required number of disks have been installed, external connections to the disk array system must be made. This section describes how to make all of the necessary connections. Basic Configuration – Making Connections Connecting the Host Interface The disk array system has dual SCSI interfaces. Refer to the following sections to make host interface connections.
SA-3340S Serial ATA Disk Array Systems Connecting the RS-232 Cable Connect the supplied RS-232 cable to the RS-232 port at the rear of the unit.
SA-3340S Serial ATA Disk Array Systems Connecting and Turning on the Power 1 Connect a power cable to a power supply connector at the rear of the unit. 2 Basic Configuration – Making Connections 2 Connect the second power cable to the remaining power supply connector. Note The system is equipped with auto switching power supplies that can run on 100 to 240 VAC. 3 Press the disk array system power switch to the ON position. The disk array system automatically begins the self-test sequence.
3 Maintenance Replacing a Disk A disk failure is indicated when the Power/Error LED at the front of the drive tray turns red and the audible alert sounds. Note Turn off the audible alert by pressing the Up and Down tons on the front panel twice simultaneously. function but- The LCD panel displays the failure with the symbol “R” or “W”. “R” indicates a disk failure or error, and “W” indicates that there are too many bad sectors on the disk. Example: • Disks 1 to 2 are members of RAID group 1.
SA-3340S Serial ATA Disk Array Systems Replacing a Power Supply 3 Maintenance – Replacing a Power Supply The disk array system is equipped with a Power Supply Fail Indicator LED at the front of the unit that turns red when one of the power supplies fails. The message “Power x failure” also appears on the LCD panel, where x refers to power supply 1, or 2, and an audible alert sounds. Note Turn off the audible alert by pressing the Up and Down buttons on the front panel twice simultaneously.
SA-3340S Serial ATA Disk Array Systems 2 Unplug the power cable connected to the failed power supply unit. 3 A B 4 Remove the power supply unit. 15 Maintenance – Replacing a Power Supply 3 Push the power supply release switch (A) in the direction illustrated and pull the power supply handle out (B) at the same time.
SA-3340S Serial ATA Disk Array Systems 5 Insert a new power supply unit in the empty power supply unit slot. The power supply automatically locks into position when fully inserted. 3 Maintenance – Upgrading Memory 6 Reconnect the power cable. Upgrading Memory The disk array system takes a single 200 pin DIMM with a maximum capacity of 1 GB. Follow these instructions to upgrade the memory.
SA-3340S Serial ATA Disk Array Systems 2 Pull the DIMM retaining clips away from the DIMM, then remove the DIMM. The DIMM springs out of the socket. 3 Note The DIMM module will fit in only one direction. Do not force the DIMM into place. 17 Maintenance – Upgrading Memory 3 Gently push the new DIMM into the socket at 45 degrees, then push the corners of the DIMM down. The DIMM is secured by the DIMM socket retaining clips.
SA-3340S Serial ATA Disk Array Systems 4 Place the top cover on the disk array system, slide it shut, then replace the three screws to fix the cover on the disk array system.
SA-3340S Serial ATA Disk Array Systems Replacing a Fan Turn off the audible alert by pressing the Up and Down tons on the front panel twice simultaneously. function but- Follow these instructions to replace a failed fan. 1 Identify the fan that has failed. Host Port 1 Host Port 2 Fan 1 Fan 2 19 Maintenance – Replacing a Fan Note 3 A fan failure is indicated by the LCD panel message “Fan x failure”, where x refers to Fan 1 or Fan 2. An audible alert also sounds.
SA-3340S Serial ATA Disk Array Systems 2 Loosen the fan enclosure thumbscrews, then pull the fan enclosure out of the chassis. ort 2 ort 2 Host P Host P ort 1 Host P ort 1 Host P 3 Maintenance – Replacing a Fan Caution High speed rotating fan blades can cause injury. Wait until both fans have stopped completely before removing either of them. 3 Unplug the power connector, remove the screws, then remove the failed fan.
SA-3340S Serial ATA Disk Array Systems 4 Secure the new fan with the screws removed in the previous step, then insert the power connector. 3 Maintenance – Replacing a Fan Caution The fan will begin rotating immediately after it is plugged in. Keep your fingers away from the blades. 5 Insert the fan enclosure into the chassis, then tighten the fan enclosure thumbscrews.
SA-3340S Serial ATA Disk Array Systems 3 Maintenance – Replacing a Fan 22
Appendix Hardware Specifications Item Specification Host Interface SCSI Ultra320 Disk Interface SATA II, 3.0 Gb/s RAID Functions • • • • Raid levels: JBOD, 0, 1, 0+1, 3, 5, 30, 50, 6, TP, NRAID Hot spare support Disk hot swapping with automatic online rebuilding Multiple RAID (max.
SA-3340S Serial ATA II Disk Array Systems Item Controller Appendix – Hardware Specifications Backplane Specification CPU Intel i80331 64-bit RISC microprocessor Disk Interface SATA II (3.
