KGUARD Standalone DVR KG-SHA116 User Manual www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual CONTENTS SAFETY INSTRUCTIONS................................................................................................................. 1 CHAPTER 1. DVR FEATURES ......................................................................................................... 2 CHAPTER 2. LAYOUT ...................................................................................................................... 3 2.1. FRONT PANEL ...................................
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.5.6. System Maintenance ......................................................................................................22 5.2.6. Network Setup......................................................................................................................22 5.2.6.1. Intranet/LAN Access Setup ............................................................................................22 5.2.6.2. Internet Access Setup ................................
KGUARD Standalone DVR KG-SHA116 User Manual Safety Instructions 1. Use proper power source. Do not use this product with a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electric shock. 3. Do not operate in wet & dusty area or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 1. DVR Features Real time monitoring Supports real time surveillance via Monitor Save Recordings DVR saves real-time recording image to HDD Backup Recordings Supports DVR backup via USB flash drive and hard drive.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 2. Layout 2.1. Front Panel Item Type 1 2 3 4 5 6 7 8 9 10 Channel Select & numeric input 11 Preview 12 13 Audio control Play Control 14 Rec.
KGUARD Standalone DVR KG-SHA116 User Manual 2.2. Rear Panel RS485/Sensor/Alarm port functions: Alarm input: Connect [-] port of your sensor to G (GND) pin, and [+] port to channel input you want to set. Alarm output: indicate the two ports marked “out”. PTZ Port：Connect your camera to RS-485A and RS485B accordingly. 4 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 2.
KGUARD Standalone DVR KG-SHA116 User Manual 2.4 Mouse Operation You can use a mouse instead of front panel keys or remote control to navigate the operation of your DVR Left button of Mouse Right button of Mouse In OSD menu, click left button to select & edit In live display mode, clicking right key will display pop-up menu bar In Main menu or sub menu mode, clicking right key will exit current menu.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 3. DVR Installation 3.1. Hard Drive Installation Caution: Please do not Install or take out hard drive when DVR is running! The model has a HDD drawer. Please use provided key to take out the HDD drawer and put HDD into the drawer correctly. (1) Remove screws and open DVR upper cover carefully; (2) Insert Power Cord and data cable into Pin of hard drive securely; (3) Put the upper cover back carefully, re-attach screws. 3.2.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 4. DVR Boot Up 4.1. System Initialization After connecting the power adapter the system will boot-up and start initializing. 4.2. Main Interface After initialization, the system will display main interface. When there are video inputs, live images from the cameras will be displayed on screen. You can use mouse to double-click the live image of any channel for full screen display; by double-clicking again, the display will return to display all cameras.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 5. DVR Menu 5.1.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2. Main Menu Press Selection button on the front panel or click the right button of mouse to display pop-up menu. Select MAIN MENU to enter main OSD menu. Press ▲, ▼, ◄, keys on front panel to move the cursor, then press Selection key to enter selected item. Or use you mouse to select and enter menu. Press ESC key or click right button of mouse to return to previous window 5.2.1.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.2. Record Setup Functions： RECORD: ON/OFF option decides to record the channel or not. QUALITY: select recording video quality, higher quality will need more HDD space to save the video. RESOLUTION: decides the recording video resolution. About the definition of resolution, please refer to the specification chapter. AUDIO: DVR supports to record 4 channels audio signal. Here you can bind the audio channel to an appointed video channel for together recording.
KGUARD Standalone DVR KG-SHA116 User Manual 4. If you want to change another recording status, repeat step 2 & step 3. 5. You can use copy function to fast complete your settings. 6. Press APPLY button to save your settings. On the main interface, you will be able to check the recording status: R: normal recording M: motion detection recording I: Sensor triggered recording 5.2.2.3. Manual Recording There are 2 short cut menus listed in the Pop-up menu: START RECORD and STOP RECORD.
KGUARD Standalone DVR KG-SHA116 User Manual Search All Recorded File: Press SEARCH button, system will search and show you the recorded status. RED color indicates ALARM recoding, GREEN color indicates continuous recording. You can click the time point to play back. System can play back 4 channels at the same time; you can select any 4 channels to play.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.3.3. Video Backup 1. Insert your USB device (USB hard disk, USB thumb drive) into the bottom USB port on the rear panel. 2. Select one or more files 3. Press BACKUP button on the menu. NOTE: Do not remove your USB device during making backup. Note: Backup files will be in H.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.4.1.1. HDD Format When a new HDD is installed into the DVR, the HDD status will show “NOT FORMATED”. You need to format the HDD otherwise the system cannot record. Select the HDD(s) you want to format and then press the FORMAT HDD icon to format the HDD(s). Warning: If you format a HDD which is being currently used, all data saved in the HDD will be lost! System will restart automatically after formatting the HDD. USB FORMAT: to format USB devices. 5.2.4.2.
KGUARD Standalone DVR KG-SHA116 User Manual Take GMAIL for example to demonstrate the email setting: 1. Set SSL to “On” via Gmail.com server, and set to “Off” via other mail server. 2. SMTP Port: indicates sender port of SMTP server. Generally the SMTP port value is 25, SMTP port of G-mail server is 465. 3. SMTP: smtp.gmail.com 4. SEND EMAIL: dvrtest@gmail.com 5. SEND PW: enter the login password of send email 6.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.4.3. Motion Detection Setup STATUS: This option allows you enable motion detection on the channels. SENSITIVITY: This option allows you to set sensitivity level of motion detection from 1 to 4 with 4 being the most sensitive. MD AREA (motion detection area): Click this button of the corresponding channel to select the area you want to have motion detection. The channel is separated into a 13*10 area.
KGUARD Standalone DVR KG-SHA116 User Manual Open auto cruise function on PTZ setting menu if you want to setup cruise function, and set up cruise channel, cruise point, total quantity and stop time (by second) etc. Channel: select the channel with the PTZ camera TOTAL: set up presetting bit (angle) quantity. Please refer to your camera’s manual for detail CUR POINT: System has default starting (current) cruise point as 01.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.5.2. Password This option allows you set the device ID for the DVR and set the system password if you want to use one. Click APPLY button to save the settings. When you have enabled Password by setting the option to “ON”, you can setup a user password and administrator password respectively. The password supports up to 6 characters. Click “APPLY” to save the settings. NOTE: Please write down your passwords and store in a safe location.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.5.3. Video Setup VIDEO SYSTEM: Select the TV system from PAL and NTSC. VIDEO PORT: keep default VGA RESOLUTION: select the VGA video output solution to match your VGA monitor from 800x600, 1024x768, 1280x1024, and 1440x900. SEQUENCE: With this function, you can select SINGLE, QUAD, NINE and SIXTEEN display mode. Take NINE mode for example: Turn ON the SEQUENCE, and then select NINE. Click the SEQUENCE icon on the right side.
KGUARD Standalone DVR KG-SHA116 User Manual (CH10~CH16) and Sixteen CHs Display (CH1~16) This mode will be disabled when the SEQUENCE display mode is ON. DWELL TIME: Allow system to display single channel in full screen or channel group by certain dwell time, and auto-switch in sequence. You can set from 0 to 300 seconds. Setting “0” will disable auto-switch display function. Select START ROLLING on the Pop-up menu to active auto-switch display mode.
KGUARD Standalone DVR KG-SHA116 User Manual 5.2.5.5. Info You can check the system information, including Device Type (model No.), Software (firmware) version and MAC address. 5.2.5.6. System Maintenance This option allows you reset the DVR to default settings, update system software (firmware), and config system auto-maintenance. When the auto-maintain function is enabled, you can set system to restart regularly to clear up some temporary storage memory. 5.2.6.
KGUARD Standalone DVR KG-SHA116 User Manual 1. Access the configuration page of your router. 2. Reserve an IP Address in your router that is not used by other computers or devices connected to your internal network. 3. Write down the assigned IP Address of your DVR, Subnet Mask, IP Address of the router (Gateway) your DVR connect to for future reference. A. Select STATIC as the network TYPE. B. Setup PORT (media port) C. Input the WEB PORT (Must be different from media PORT) D.
KGUARD Standalone DVR KG-SHA116 User Manual We recommend applying a free DDNS account at www.dyndns.org If your ISP uses STATIC IP network, select STATCI network TYPE. 1. Input the PORT (media port) 2. Input the WEB PORT (Must be different from media PORT) 3. Enter the IP Address that you have reserved at the beginning of this section into this field to be the unique address of your DVR in your local network 4. NETMASK: It is recommended to leave the Subnet mask as the default 255.255.255.0. 5.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 6. Network Access There are 3 methods to remote access the DVR via network: Internet Explorer Browser (IE), Netviewer client software & Mobile phones. 6.1. IE & Netviewer Access You can use Netviewer client software & Internet Explorer (IE) 6.0 or newer version to remote access the DVR. 6.1.1.
KGUARD Standalone DVR KG-SHA116 User Manual after the ActiveX Control has been installed. Enabling all ActiveX controls put your computer at risk of being attacked by computer virus. 6.1.2. Connect to DVR To connect to the DVR from a remote computer, you would then open an Internet Explorer browser window and enter the Internet IP of your router that you received by going to www.myipaddress.com.
KGUARD Standalone DVR KG-SHA116 User Manual 6.1.3.1 Live 1. On / Off Live display [ ]: When the live display status is “On”, clicking the button to close live display. When the live display status is “Off”, clicking the button to open live display. 2. Capture [ ]: Capture Screen image and save to PC as *bmp image. 3. Recording [ ]: Operate DVR recording remotely 4.
KGUARD Standalone DVR KG-SHA116 User Manual 6.1.3.5. Remote Backup You can backup recorded video files from DVR to your PC using the Replay menu in the remote surveillance software. To backup files remotely: 1. Click REPLAY at the top of the main screen. 2. Select a date on the calendar and click RELOAD. 3. Double-click a file from the File List to begin playback. 4. Click BACKUP.
KGUARD Standalone DVR KG-SHA116 User Manual 6.1.3.8. Playback Local File with Netviewer Run the Netviewer software, you will see the OFFLINE button displayed on the Login interface. Press this button to enter local file playback mode. Press the ADD button to add backup H.264 files or folder saved in your computer, you will see the files will be listed in the queue window, select a file then press PLAYFILE button to play. 29 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 6.2. Mobile Phones Access This function allows you to view 1 channel live image at the same time with your mobile phone. The DVR is currently compatible with mobile phones running Windows® Mobile, Symbian® S60 3rd/5th Edition operating systems, iPhones® and Blackberry® on GPRS and/or 3G networks. 6.2.1. Mobile Setup Before you can view the live image from your DVR with compatible mobile phones, you need to set the settings first.
KGUARD Standalone DVR KG-SHA116 User Manual 3. Choose storage location and click “Install” to start the installation. 4. After installation finishes, click the icon named window mobile to run the program. This will display the program screen. 5. Click the “Setting” button to enter the Setting menu.
KGUARD Standalone DVR KG-SHA116 User Manual 6.2.1.2. Install & Operate Mobile Client in Symbian® Phones 1. Install the webcam program that is included on the supplied CD by copying the “Symban_3.0.sisx” (Symbian 3.0 version) or “Symbian_5.0.sis” (Symbian 5.0 version) file to the mobile phone. You can do this by attaching the mobile phone to a computer and copying the file from the CD to the phone. 2. Select the Symbian_3.0/Symbian_5.0 icon in this window to install it. 3.
KGUARD Standalone DVR KG-SHA116 User Manual 6. Click “Continue” and wait for the program to install. 5. Once the installation is complete, go to the Applications folder and select the “Symbian_5.0” program, and click “Open” to display the settings menu. Default Access Point：Input the access point. System default for the access point is GPRS connection. Server Address: DVR’s public IP address or DDNS domain name Server Port：Same as the Server Port you set in the DVR under section 5.2.10.4.
KGUARD Standalone DVR KG-SHA116 User Manual 6.2.1.3. Install & Operate Mobile Client in iPhone® Step 1: Download iTunes Visit Apple website http://www.apple.com/itunes/ to download & install the iTunes. Step 2: Download & install surveillance software “Aplayer” 2.1 Register iTunes Store 2.1.1 Run the installed iTunes, you might need to create an account to visit iTunes store firstly. Move to the menu “Store”, and click the option “Create Account”. 2.1.2 Continue 34 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 2.1.3 Select & continue 2.1.4 Fill in your personal info & continue. Please note that the options of Payment Method are different from different regions, please select another payment method. Don’t worry, “Aplayer” is free software & you don’t need to pay for it. 2.1.5 Finished the register, and go to your email box to verify your account. ** 35 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual Click the link included in the email message. It will connect to the iTunes store and turn to iTunes interface. Sign in your account. The register of your iTunes store account has been done. 36 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 2.2 Authorize Computer You need to authorize your computer with the registered ID. Move to the menu “Store”, and click the option “Authorize Computer”. Input your registered ID & password, then click Authorize button. 2.3 Download & install “Aplayer” into your iPhone 2.3.1 Click iTunes Store(1), then input “aplayer” into the search bar(2) on the right upper corner and press Enter. 2 1 You will find the Aplayer icon displayed as below. 37 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 2.3.2 Click the icon and it will turn to the download page. Click the “GET APP” button to download the file. You will find the downloaded file on the directory of Application 2.3.3 Connect your iPhone to the computer, you will find your Device displayed on the left sidebar. Select the DEVICES ID(1), and then click “Applications” option(2). Select the “Sync Applications” & “Aplayer” (3) and then click “Sync” button(4). 2 3 4 1 38 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual The devices ID is different from different iPhones. After finishing the sync, you will find the Aplayer Icon on your iPhone Step 3: Setup & run “Aplayer” Main interface of Aplayer & function keys: Ⅰ. Direction keys of PTZ control Ⅱ. Zoom+ & ZoomⅢ. Focus+ & FocusⅣ. Iris+ & IrisⅤ. Channel selection keys Ⅵ. Play & Pause Ⅶ. Snapshot Ⅷ. Full screen Ⅸ. Next group of channels Ⅹ. Setup Ⅰ Ⅵ ⅡⅢⅣ Ⅶ Ⅷ Ⅸ Ⅴ Ⅹ 3.
KGUARD Standalone DVR KG-SHA116 User Manual 6.2.1.4. Blackberry Handheld Application Installation Guide 1. 2. 3. 4. Install the Blackberry desktop manager on the computer; Connect the handheld to computer using the USB port; Open the Blackberry desktop manager; Select the [Application Loader] item in the main menu; 5. Click the start button on the [Add / Remove Application] side; 40 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual 6. Browse and open the [*.alx] file then click [Next]; 7. Just click the [Finish] button to complete the installation. 41 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual The startup shortcuts are usually located in the Downloads directory. Main screen of the application. 42 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 7. Specifications Model KG-SHA116 Video Compression H.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 8. System Connection Configuration 44 www.kguardsecurity.
KGUARD Standalone DVR KG-SHA116 User Manual Chapter 9. Appendix 9.1 Operation Function Table Type Title Description Page Time setting Setting system date, time and format and day-light saving time setting 18 Setting system language 21 Language Select CH Setting Setting CH title and position; adjusting image color parameter value; setting CH display to ON / Off and time display/recording time overlaying to On/Off. 10 Rec.
KGUARD Standalone DVR KG-SHA116 User Manual 9.2 Recording Alarm setting Please refer the below matrix: “ ⊥” stand for “only alarm but no recording”; “AMR” stand for “alarm recording”; “NLR” stand for “normal recording”; and “NOR” stand for “ no recording”. Once alarm is triggered, alarm icon will occur, and when many alarms are triggered, alarm remarks will occur on the screen.
KGUARD Standalone DVR KG-SHA116 User Manual 9.4. Email server check list（The below info only for your ref.） （Web site） www.yahoo.com www.google.com Email address Sender server（25） Receiver server（110） @yahoo.com.tw smtp.mail.yahoo.com.tw pop.mail.yahoo.com.tw @yahoo.com smtp.mail.yahoo.com pop.mail.yahoo.com @gmail.com smtp.gmail.com(465/587) pop.gmail.com(995) 9.5. Usage Maintenance 1. 2. 3. 4. 5. Please make sure DVR keep away from heating source.
KGUARD Standalone DVR KG-SHA116 User Manual 9.7 HDD Device Support List Brand Seagate WD Maxtor Hitachi Samsung SHA Series – SATA HDD Support Suggestion Model No. Note Capacity 80G ST380815AS 160G ST3160815SV ST3250310SV ST3250410AS 250G ST3250312CS ST3250310SV 320G ST3320410SV ST3500312CS ST3500320AS Special design for Standalone DVR. 500G ST3500320SV ST3500320NS Special design for Standalone DVR. ST3500410SV 750G ST3750330SV 1T ST31000322CS 1T ST31000340NS Special design for Standalone DVR. 1.
KGUARD Standalone DVR KG-SHA116 User Manual 160G 500G HD161HJ HD501IJ/CNG 9.8 3G Cell Phone Support List 3G Cell phone Support Suggestion Brand Nokia Motorola Sony Ericsson Samsung HTC Apple Blackberry Model No. N70 N73 N95 E65 V3x E770 SE K600i SE k700i SE 700i SE 800i Z610i SGH 400 TyTNII CHT9000 iPhone 9000 9530 9630 Note PDA Phone 49 www.kguardsecurity.
The material in this document is the intellectual property of our department . No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our department prior writt en permission. Our products are under continual improvement and we reserve the right t o make changes without noti ce. But no guarantee is given as to the correctness of its contents. We do not undertake any responsibility for the harms cause by using our product.
