DiamondMax 8S 40GB Serial ATA Product Manual May 13, 2005 Revision 1 Part Number: 000001912
Maxtor® Corporation, May 13, 2005. All rights reserved. Printed in U.S.A. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein – which will be incorporated in revised editions of the publication. Maxtor may make changes or improvements in the product(s) described in this publication at any time and without notice. UL/CSA/VDE/TUV /RoHS UL standard 1954 recognition granted under File No. E78016 CSA standard C22.
This product or document is protected by copyright and distributed under licences restricting its use, copying, distributing, and decompilation. No part of this product or document may be reproduced in any form by any means without prior written authorization of Maxtor and its licensors, if any.
Please do not remove or cover up Maxtor factory-installed drive labels. They contain information required should the drive ever need repair.Thank you for your interest in Maxtor hard disk drives. This manual provides technical information for OEM engineers and systems integrators regarding the installation and use of Maxtor hard drives. Drive repair should be performed only at an authorized repair center. For repair information, contact the Maxtor Customer Service Center at 800-2MAXTOR or 1-303-678-2015.
TABLE OF CONTENTS Chapter 1 INTRODUCTION 1.1 1.2 1.3 1.4 1.5 MAXTOR CORPORATION ............................................................................... 1-1 AUDIENCE ............................................................................................................. 1-1 MANUAL ORGANIZATION..................................................................................1-1 TERMINOLOGY AND CONVENTIONS ........................................................... 1-2 REFERENCES ...............
Chapter 4 INSTALLATION 4.1 SPACE REQUIREMENTS ..................................................................................... 4-1 4.2 UNPACKING INSTRUCTIONS........................................................................... 4-2 4.3 HARDWARE OPTIONS ....................................................................................... 4-4 4.3.1 JUMPER POSITION....................................................................................... 4-4 4.3.2 STAGGER SPIN-UP ......................
Table of Contents LIST OF FIGURES Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Mechanical Dimensions.................................................................................4-1 Single Pack Shipping Container..................................................................... 4-2 25-Pack Shipping Container ......................................................................... 4-3 SATA Power/Interface Connector .........................................
Table of Contents LIST OF TABLES Table 4-1 Table 4-2 Table 4-3 Table 5-1 Table 5-2 SATA Pin 11 Configuration....................................................................................4-5 Device Plug Connector Pin Definitions ..................................................................4-12 Logical Addressing Form.........................................................................................4-16 Supported Commands.....................................................................
Introduction Chapter 1 Introduction 1.1 Maxtor Corporation Maxtor corporation is one of the world’s largest suppliers of hard disk drive productsproducts that help store the digital world for millions of users.
Introduction • Chapter 5 – SATA Bus Interface and ATA Commands • Chapter 6 – Service and Support • Glossary 1.4 TERMINOLOGY AND CONVENTIONS In the Glossary at the back of this manual, you can find definitions for many of the terms used in this manual.
Introduction • NCQ Native Command Queuing • SATA Serial ATA • SOF Start Of Frame • tpi tracks per inch • µs microseconds • V volts The typographical and naming conventions used in this manual are listed below. Conventions that are unique to a specific table appear in the notes that follow that table. Typographical Conventions: • Names of Bits: Bit names are presented in initial capitals. An example is the Host Software Reset bit. • Commands: Interface commands are listed in all capitals.
Introduction Attachment, visit the Serial ATA working group at http://www.serialata.
General Description Chapter 2 PRODUCT DESCRIPTION 2.1 PRODUCT DESCRIPTION Maxtor drive leadership continues with the DiamondMax 8S 40GB Serial ATA drive - a single head, 7200RPM product. The DiamondMax 8S 40GB Serial ATA drives combine performance and value with the Serial ATA interface making a perfect choice for entry level consumers and commercial/business desktop systems transitioning to the new interface.
General Description • Low weight to reduce shipping costs • Improved reliability with: ~ Shock Protection System ~ Data Protection System 2.2 THE SERIAL ATA INTERFACE Serial ATA is the next generation ATA interface. It provides faster data transfer speeds, more bandwidth, more potential for speed increases in future generations and better data integrity. Serial ATA hardware is smaller and more compact than traditional parallel ATA components.
General Description • Emulation of IBM® PC AT® task file register, and all AT fixed disk commands • Windows 2000TM, WinXP, and 9X Certification Performance • Native Command Queuing • 10.1 ms seek time • Average rotational latency of 4.17ms • 2 MB buffer with 1.9MB (approximate) Advance Cache Management (ACM).
General Description 2.4 REGULATORY COMPLIANCE STANDARDS Maxtor Corporation’s disk drive products meet all domestic and international product safety regulatory compliance requirements. Maxtor’s disk drive products conform to the following specifically marked Product Safety Standards: • Underwriters Laboratories (UL) Standard 1950. This certificate is a category certification pertaining to all 3.5-inch series drives models. • Canadian Standards Association (CSA) Standard C.22.2 No. 1950.
Product Specifications Chapter 3 PRODUCT SPECIFICATIONS 3.1 Models and Capacities MODEL NUMBERS NON ROHS COMPLIANT ROHS COMPLIANT * 6E040T0 6N040T0* Formatted Capacity (GB LBA Mode) 40GB GB means 1 billion bytes. Total accessible capacity varies depending on operating environment. * Complies with European Union Directive on Restriction of Hazardous Substances (Section 3.13) 3.
Product Specifications MODEL 6E040T0 Recording Density (kbpi, ID/OD) Track Density (ktpi) 3.3 40GB ID = 713 OD = 560 88.7 Performance Specifications MODEL 6E040T0 40GB Seek Times (typical read, ms) Track-to-Track Seek 0.8 Average (normal seek) ≤ 10.1 Full Stroke (normal seek) ≤ 18.0 Average Latency (ms) 4.17 Controller Overhead (ms) <0.3 Rotation Speed (RPM ±0.5%) 7200 Data Transfer Speed (MByte/sec max) Interface Transfer Speed (Gb/s) 1.5 To/From Media (ID/OD up to nn.n, where nn.
Product Specifications 3.5 Power Requirements MODE 12V (MA) 5V (MA) POWER (W) 1562 621 21.8 Seek 502 392 8.0 Read/Write 461 414 7.6 Idle 425 230 6.2 Standby 36 229 1.6 Sleep 36 228 1.6 Spin-up (peak) Note: Power numbers are typical values. 3.6 Power Mode Definitions Spin-up The disk drive is spinning up following initial application of power and has not yet reached full speed. Seek A random access operation by the drive.
Product Specifications 3.7 EPA Energy Star Compliance Maxtor Corporation supports the goals of the U.S. Environmental Protection Agency’s Energy Star program to reduce the electrical power consumption of computer equipment. 3.8 Environmental Limits PARAMETER 0° C to 60° C Temperature NON-OPERATING/ STORAGE OPERATING low temperature (-40° C) high temperature (71° C) per MIL-STD-810E, method 501.3, climatic category; hot-induced conditions.
Product Specifications 3.9 Shock and Vibration PARAMETER OPERATING NON-OPERATING Mechanical Shock R=0.988/shock at 60 Gs; R= 0.999/shock at 30 Gs 2 msec, 1/2 sine R=0.90@>= 300G R=0.95@>= 250G R=0.99@>= 200G Rotational Shock R=0.988 @ 2000 rad/sec2 R=0.95 @ 20K rad/sec2,1ms input R=0.99 @ 15K rad/sec2,2ms input Rotational Random Vibration 10 - 2000 Hz 12.5 rad/sec2 RMS Overall 2 - 300 Hz 96.5 rad/sec2 RMS Random Vibration 10 - 2000 Hz 0.86 GRMS Overall PSD: 7 - 800 Hz at 3.
Product Specifications 3.10 Reliability Specifications Annualized Return Rate <1.0% Annualized Return Rate (ARR) indicates the average against products shipped. ARR includes all reasons for returns (failures, handling, damage, NDF) but does not include inventory credit returns. Load/Unload Cycles 50,000 This indicates the average minimum cycles for reliable load/unload function. Data Reliability <1 per 10e15 bits read- Data errors (non-recoverable).
Product Specifications 3.12 Safety Regulatory Compliance All Maxtor hard drives comply with relevant product safety standards such as CE, CUL, TUV and UL rules and regulations. As delivered, Maxtor hard drives are designed for system integration before they are used. 3.13 RoHS Compliance Versions of DiamondMax 8S drives, commonly called RoHS, will become available during 2005 that will meet the Restriction of Hazardous Substances (RoHS) compliance directive of the European Union as applicable.
Installation Chapter 4 INSTALLATION This chapter explains how to unpack, configure, mount, and connect the Maxtor DiamondMax 8S 40GB SATA hard disk drive prior to operation. It also explains how to start up and operate the drive. 4.1 SPACE REQUIREMENTS The Maxtor DiamondMax 8S 40GB SATA hard disk drives are shipped without a faceplate. Figure 4-1 shows the external dimensions of the Maxtor DiamondMax 8S 40GB SATA drives. (Diagram used for illustrative purposes.
Installation 4.2 UNPACKING INSTRUCTIONS CAUTION: The maximum limits for physical shock can be exceeded if the drive is not handled properly. Special care should be taken not to bump or drop the drive. It is highly recommended that Maxtor DiamondMax 8 SATA drives are not stacked or placed on any hard surface after they are unpacked. Such handling could cause media damage. 1. Open the shipping container and remove the packing assembly that contains the drive. 2. Remove the drive from the packing assembly.
Installation Figure 4-3 25 Pack Shipping Container Maxtor DiamondMax 8S 40GB SATA 4-3
Installation 4.3 HARDWARE OPTIONS The configuration of a Maxtor DiamondMax 8S 40GB SATA hard disk drive depends on the host system in which it is to be installed. This section describes the hardware options that you must take into account prior to installation. 4.3.1 Jumper Position The DiamondMax 8S 40GB SATA interface connector shown in Figure 4-4 includes a position for a jumper. See section 4.3.2 Staggered Spin-up, for details on how the jumper is used. 4.3.
Installation Figure 4-4 DiamondMax 8S 40GB SATA Power/Interface Connector Maxtor DiamondMax 8S 40GB SATA 4-5
Installation For systems using Serial ATA cables, the Serial ATA II specification mandates that host systems connecting to disk drives using SATA cables must ground Pin 11, resulting in disabling staggered spin-up. Typical desktop systems use this configuration.
Installation 4.4 MOUNTING Drive mounting orientation, clearance, and ventilation requirements are described in the following subsections. 4.4.1 Orientation The mounting holes on the Maxtor DiamondMax 8S 40GB SATA hard disk drives allow the drive to be mounted in any orientation. Figure 4-5 shows the location of the three mounting holes on each side of the drive. The drive can also be mounted using the four mounting hole locations on the PCB side of the drive.
Installation Clearance from the drive to any other surface (except mounting surfaces) must be a minimum of 1.25 mm (0.05 inches).
Installation 4.4.2 Ventilation The Maxtor DiamondMax 8S 40GB SATA hard disk drives operate without a cooling fan, provided the ambient air temperature does not exceed 140° F (60° C). 4.5 COMMBINATION CONNECTOR (J1) The DiamondMax 8S 40GB SATA is equipped with a serial ATA interface connector with integrated power connector, as shown in Figure 4-4. 4.5.1 DC Power (J1, Section A) The recommended mating connectors for the +5 VDC and +12 VDC input power are listed in Table 4-2.
Installation 4.6 FOR SYSTEMS WITH A MOTHERBOARD CONTAINING AN EMBEDDED SATA HOST You can install the Maxtor DiamondMax 8S 40GB SATA hard disk drive in a SATA compatible system that contains a SATA bus connector on the motherboard. To connect the DiamondMax hard disk drive to the motherboard use a SATA cable to connect the drive to the motherboard. Note that power and signal cables should be connected before power is applied to the drive or motherboard. 4.
Installation Table 4-2 Device Plug Connector Pin Definitions Signal Segment S1 Ground S2 A+ S3 A- S4 Ground S5 B- S6 B+ S7 Ground 2nd Mate Differential signal pair A from Phy 2nd Mate Differential signal pair B from Phy 2nd Mate Signal Segment “L” Central Connector Polarizer Power Segment “L” Power Segment P1 V33 3.3V power1 P2 V33 3.3V power1 P3 V33 3.
Installation Note 2. Host system should ground P4,P5, and P6. Failure to do so may cause improper drive operation. The following points should be noted: All pins are in a single row, with a 1.27 mm (.050”) pitch. • The comments on the mating sequence apply to the case of backplane blind mate connector only. In this case, the mating sequences are: (1) the ground pins P4 and P12; (2) the precharge power pins and the other ground pins; and (3) the signal pins and the rest of the power pins.
Installation Figure 4-8 Completing the Drive Installation Maxtor DiamondMax 8S 40GB SATA 4-13
ATA Bus Interface and ATA Commands Chapter 5 SATA BUS INTERFACE AND ATA COMMANDS This chapter describes the interface between DiamondMax 8S 40GB Serial ATA hard disk drives and the Serial ATA bus. The commands that are issued from the host to control the drive are listed, as well as the electrical and mechanical characteristics of the interface. 5.1 INTRODUCTION Maxtor DiamondMax 8S 40GB Serial ATA hard disk drives use the Serial ATA interface.
ATA Bus Interface and ATA Commands 5.5.2 Supported Commands The DiamondMax 8S 40GB Serial ATA hard disk drives support all the mandatory commands from the general feature set for devices not supporting the Packet command feature set. Refer to the ATA/ATAPI-7, volume 1 standard for a detailed description of these commands. The IDENTIFY DRIVE command, however, is elaborated in Identify Drive Command Parameters, table 5-2. Table 5-1 lists the supported commands.
ATA Bus Interface and ATA Commands Table 5-1 Supported Commands Command Command Code Feature Register Value(s) READ NATIVE MAX ADDRESS F8h READ NATIVE MAX ADDRESS EXT 27h READ SECTOR(S) 20h, 21h READ SECTOR(S) EXT 24h READ DMA EXT 25h READ DMA QUEUED C7h READ DMA QUEUED EXT 26h READ MULTIPLE EXT 29h READ VERIFY SECTOR(S) 40h, 41h READ VERIFY SECTOR(S)EXT 42h READ FPDMA QUEUED 60h SECURITY DISABLE PASSWORD F6h SECURITY ERASE PREPARE F3h SECURITY ERASE UNIT F4h SECURITY FREEZE
ATA Bus Interface and ATA Commands Table 5-1 Supported Commands Command Code Command Feature Register Value(s) SET MULTIPLE MODE C6h SLEEP 99h, E6h SMART DISABLE AUTO OFFLINE B0h DBh SMART DISABLE OPERATIONS B0h D9h SMART ENABLE OPERATIONS B0h D8h SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE B0h D2h SMART EXECUTE OFF-LINE IMMEDIATE B0h D4h SMART READ DATA B0h D0h SMART READ LOG B0h D5h SMART RETURN STATUS B0h DAh SMART SAVE ATTRIBUTE VALUES B0h D3h SMART WRITE LOG B0h D6h ST
ATA Bus Interface and ATA Commands Table 5-1 Supported Commands Command Code Command WRITE MULITPLE EXT 39h WRITE VERIFY 3Ch WRITE DMA FUA EXT 3Dh WRITE DMA QUEUED FUA EXT 3Eh Feature Register Value(s) Note: 1. As defined in the ATA/ATAPI-6 standard. Identify Drive Command This command allows the host to receive parameter information from the drive. When the command is received, the drive: 1. Sets BSY 2. Stores the required parameter information in the sector buffer 3. Sets the DRQ bit 4.
ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameter Word 0 Content Description General configuration bit-significant information: 15: 0 = ATA device 14-8: Retired 7: 1 = removable media device 6: Obsolete 5-3: Retired 2: Response incomplete 1: Retired 0: Reserved 1 Obsolete 2 Specific configuration 3 Obsolete 4-5 Retired 6 Obsolete 7-8 9 Reserved for assignment by the CompactFlash Association Retired 10-19 Serial number (20 ASCII characters) 20-21 R
ATA Bus Interface and ATA Commands Word 49 Content Description Capabilities 15-14: Reserved for the IDENTIFY PACKET DEVICE command. 13: 1 = Standby timer values as specified in this standard are supported. 0 = Standby timer values shall be managed by the device 50 51-52 12: Reserved for the IDENTIFY PACKET DEVICE command. 11: 1 = IORDY supported. 0 = IORDY may be supported 10: 1 = IORDY may be disabled 9: 1 = LBA supported 8: 1 = DMA supported.
ATA Bus Interface and ATA Commands Word 53 Content Description 15-3: Reserved 2: 1 = the fields reported in word 88 are valid. 0 = the fields reported in word 88 are not valid 1: 1 = the fields reported in words (70:64) are valid.
ATA Bus Interface and ATA Commands Word 65 Content Description Minimum Multiword DMA transfer cycle time per word 15-0: 66 Manufacturer’s recommended Multiword DMA transfer cycle time 15-0: 67 Cycle time in nanoseconds Minimum PIO transfer cycle time without flow control 15-0: 68 Cycle time in nanoseconds Cycle time in nanoseconds Minimum PIO transfer cycle time with IORDY flow control 15-0: Cycle time in nanoseconds 69-70 Reserved (for future command overlap and queuing) 71-74 Reserved for
ATA Bus Interface and ATA Commands Word 80 Content Description Major version number 0000h or FFFFh = device does not report version 15: Reserved 14: Reserved for ATA/ATAPI-14 13: Reserved for ATA/ATAPI-13 12: Reserved for ATA/ATAPI-12 11: Reserved for ATA/ATAPI-11 10: Reserved for ATA/ATAPI-10 9: Reserved for ATA/ATAPI-9 8: Reserved for ATA/ATAPI-8 7: 1 = supports ATA/ATAPI-7 6: 1 = supports ATA/ATAPI-6 5: 1 = supports ATA/ATAPI-5 4: 1 = supports ATA/ATAPI-4 3: 1 = supports ATA-3
ATA Bus Interface and ATA Commands Word 81 Content Description Minor version number 0000h or FFFFh = device does not report version. 0001h-FFFEh = see 6.16.41 of ATA/ATAPI-7 specification 82 Command set supported.
ATA Bus Interface and ATA Commands Word 83 Content Description Command sets supported.
ATA Bus Interface and ATA Commands Word 84 Content Description Command set/feature supported extension.
ATA Bus Interface and ATA Commands Word 85 Content Description Command set/feature enabled.
ATA Bus Interface and ATA Commands Word 86 Content Description Command set/feature enabled.
ATA Bus Interface and ATA Commands Word 87 Content Description Command set/feature default. 15: Shall be cleared to zero 14: Shall be set to one 13: 1= The device supports IDLE IMMEDIATE with UNLOAD FEATURE 12: Reserved for technical report 11: Reserved for technical report 10: 1= The device supports the URG bit for WRITE STREAM DMA EXT and WRITE STREAM EXT commands 9: 1= The device supports the URG bit for READ STREAM DMA EXT and READ STREAM EXT commands.
ATA Bus Interface and ATA Commands Word 88 Content Description 15: Reserved 14: 1 = Ultra DMA mode 6 is selected. 0 = Ultra DMA mode 6 is not selected 13: 1 = Ultra DMA mode 5 is selected. 0 = Ultra DMA mode 5 is not selected 12: 1 = Ultra DMA mode 4 is selected. 0 = Ultra DMA mode 4 is not selected 11: 1 = Ultra DMA mode 3 is selected. 0 = Ultra DMA mode 3 is not selected 10: 1 = Ultra DMA mode 2 is selected. 0 = Ultra DMA mode 2 is not selected 9: 1 = Ultra DMA mode 1 is selected.
ATA Bus Interface and ATA Commands Word 93 Content Description Hardware reset result. The contents of bits (12:0) of this word shall change only during the execution of a hardware reset 15: Shall be cleared to zero. 14: Shall be set to one. 13: 1 = device detected CBLID- above ViH. 0 = device detected CBLIDbelow ViL 12-8: Device 1 hardware reset result. Device 0 shall clear these bits to zero. Device shall set these bits as follows: 12: Reserved. 11: 0 = Device 1 did not assert PDIAG-.
ATA Bus Interface and ATA Commands Word 94 Content Description 15-8: Vendor’s recommended acoustic management value. 7-0: Current automatic acoustic management value 95 Stream Minimum Request Size 96 Stream Transfer Time - DMA 97 Stream Access Latency - DMA 98-99 100-103 Streaming Performance Granularity Maximum user LBA for 48-bit Address feature set.
ATA Bus Interface and ATA Commands Word 116 Content Description Reserved for technical report 117-118 Logical Sector Size The value shall be equal to or greater than 256. The value in words 117,118 shall be valid when word 106 bit 12 is set to 1. All logical sectors on a device shall be 117,118 words long.
ATA Bus Interface and ATA Commands Word 128 129-159 160 Content Description Security status 15-9: Reserved 8: Security level 0 = High, 1 = Maximum 7-6: Reserved 5: 1 = Enhanced security erase supported 4: 1 = Security count expired 3: 1 = Security frozen 2: 1 = Security locked 1: 1 = Security enabled 0: 1 = Security supported Vendor specific CFA power mode 1 15: Word 160 supported 14: Reserved 13: CFA power mode 1 is required for one or more commands implemented by the device 12:
Service and Support Chapter 6 SERVICE AND SUPPORT 6.1 GETTING HELP Before contacting Maxtor Support, use the Hard Disk Information feature in MaxBlast to view the model number and serial number of your drive. These numbers can be used to get help from Maxtor Support, register your drive, and look up information on the Maxtor website. Please visit www.maxtor.
GLOSSARY A ACCESS – (v) Read, write, or update information on some storage medium, such as a disk. (n) One of these operations. ACCESS TIME – The interval between the time a request for data is made by the system and the time the data is available from the drive. Access time includes the actual seek time, rotational latency, and command processing overhead time. See also seek, rotational latency, and overhead. ACTUATOR – Also known as the positioner.
GLOSSARY SCSI structure used to communicate requests from an initiator (system) to a target (drive). CLEAN ROOM – An environmentally controlled dust-free assembly or repair facility in which hard disk drives are assembled or can be opened for internal servicing. CLUSTER – A group of sectors on a disk drive that is addressed as one logical unit by the operating system. CONTROLLER – Short form of disk controller.
GLOSSARY EMBEDDED SERVO – A timing or location signal placed on the disk’s surface on the tracks that also store data. These signals allow the actuator to fine-tune the position of the read/write heads. ENCODING – The protocol by which particular data patterns are changed prior to being written on the disk surface as a pattern of On and Off or 1 and 0 signals.
GLOSSARY HARD DISK – A type of storage medium that retains data as magnetic patterns on a rigid disk, usually made of an iron oxide or alloy over a magnesium or aluminum platter. Because hard disks spin more rapidly than floppy disks, and the head flies closer to the disk, hard disks can transfer data faster and store more in the same volume. HARD ERROR – A repeatable error in disk data that persists when the disk is reread, usually caused by defects in the media surface.
GLOSSARY subsequent blocks in advance to anticipate the next request for data. The look ahead technique speeds up disk access of sequential blocks of data. LOW-LEVEL FORMATTING – Formatting that creates the sectors on the platter surfaces so the operating system can access the required areas for generating the file structure. Maxtor drives are shipped with the low-level formatting already done. M MB – See megabyte.
GLOSSARY PLATED MEDIA – Disks that are covered with a hard metal alloy instead of an iron-oxide compound. Plated disks can store greater amounts of data in the same area as a coated disk. PLATTER – An disk made of metal (or other rigid material) that is mounted inside a fixed disk drive. Most drives use more than one platter mounted on a single spindle (shaft) to provide more data storage surfaces in a small package.
GLOSSARY SCSI – Acronym for Small Computer System Interface, an American National Standards Institute (ANSI) version of Shugart Associates' SASI interface between the computer and controller. SCSI has grown in popularity and is one of the most flexible and intelligent interfaces available. SECTOR – A section of space along a track on the disk, or the data that is stored in that section. Hard disks most often have sectors that are 512 data bytes long plus several bytes overhead for error correcting codes.
GLOSSARY disk sends and receives data from the controller. Drive specifications usually reference a high number that is the burst mode rate for transferring data across the interface from the disk buffer to system RAM. Sustained data transfer is at a much lower rate because of system processing overhead, head switches, and seeks. WRITE ONCE – In the context of optical disks, technologies that allow the drive to store data on a disk and read it back, but not to erase it.
Index A abbreviations 1-2 adapter board 2-4, 4-9,4-10 C clearance 4-6,4-7,4-8 command descriptions 5-2 to 5-21 connector 4-10,4-11,4-12 F faceplate 4-1 S shipping container 4-2,4-3 space requirements, 4-1 T terminology and conventions, 1-2,13 U unpacking instructions, 4-2,4-3 V ventilation, 4-9 H hardware options 4-4 hardware requirements, 2-4 J jumper configurations 4-6 jumper locations 4-5 jumper options 4-6 M maximum screw torque 4-6 mechanical dimensions 4-8 motherboard 4-10 mounting 4-10,4-13 moun
