Product Manual

ManualsBrandsMaxsa Innovations ManualsLightingMaxsa Motion Sensor LED Outdoor Wall Sconce — 85 Lumens, Battery Powered

ABOUT YOUR LED OUTDOOR WALL SCONCE

BATTERY INSTALLATION

To access the battery compartment, remove the 2 thumb

screws from the top cover. Remove the top cover.

BATTERY INSTALLATION (CONTINUED)

Remove the battery compartment cover by squeezing

the two tabs on the cover inward and pulling up.

page 1

Thumb Screw

Battery Compartment Cover

4 C Batteries (not included)

Squeeze tabs inward

Insert four 1.5V

C batteries in the proper

orientation

ASSEMBLY AND INSTRUCTION GUIDE

Model #s 43319,

44219, 46219 and 48219

The LED Outdoor Wall Sconce is perfect for porches,

doorways, or around the house.

The LED Outdoor Wall Sconce has a built-in motion sensor,

which automatically turns on the light when movement of a

heat source (such as people, animals, or cars) is detected in

the area. The light remains on while motion continues to be

detected in the area.

The LED Outdoor Wall Sconce also has a built-in photosensor

so that the light only turns on at night.

The LED Outdoor Wall Sconce may function irregularly or not

at all at temperatures below 0° F / -17.8° C. Normal opera-

tion will return when the temperature rises.

The LED Outdoor Wall Sconce requires 4 C cell batteries (not

included). The batteries typically last up to 1 year under

normal use.

The 2 super bright Surface Mount LEDs in the LED Outdoor

Wall Sconce produce a warm white light (~3000K) and have

an estimated life of 30,000 hours so they should never need

changing.

Batteries are not included, so you will need to provide four (4)

new C cell batteries.

Install the 4 C cell batteries in the proper

+/- polarity orienta-tion as shown in the illustration above.

The positive ends of the batteries should face the low battery

contacts and the negative ends of the batteries should face

the elevated spring terminals in the battery compartment. If

your unit includes a clear rubber spacer between the two

halves of the battery compartment, please reinsert it between

the two halves.

5. Reinstall the battery compartment cover by aligning the tabs

and pressing the battery compartment cover down until the

battery compartment cover clicks into place.

NOTE: When you close the battery compartment, the light

should activate immediately, regardless of lighting conditions

or motion. This is a test activation to show there is power

flowing from the battery to the light. It should last roughly

30 seconds. After this test activation, the light will function

normally.

6. Reassemble the LED Outdoor Wall Sconce by replacing the

top cover and re-installing the two thumb screws. Tighten the

thumb screws by hand as tightly as possible to ensure a

waterproof seal.

Batteries not included

NOTE: Do not mix old and new batteries. Do not mix alkaline,

standard (carbon-zinc), or rechargeable (Nickel-Cadmium)

batteries.

Summary of content (6 pages)

PAGE 1
page 1 ASSEMBLY AND INSTRUCTION GUIDE Model #s 43319, 44219, 46219 and 48219 ABOUT YOUR LED OUTDOOR WALL SCONCE The LED Outdoor Wall Sconce is perfect for porches, doorways, or around the house. The LED Outdoor Wall Sconce has a built-in motion sensor, which automatically turns on the light when movement of a heat source (such as people, animals, or cars) is detected in the area. The light remains on while motion continues to be detected in the area.
PAGE 2
page 2 CHOOSING A LOCATION, CONTINUED BATTERY INSTALLATION (CONTINUED) Note: If your LED Outdoor Wall Sconce does not turn on after battery installation: • Make sure the batteries have been inserted matching the correct + / - polarity orientation and are making secure contact with the terminals. • Make sure you are testing the LED Outdoor Wall Sconce in a dark area since the light will only turn on at night. Note: Dispose of old batteries properly, following your local and state regulations.
PAGE 3
page 3 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Light does not turn on when there is movement in the detecton area. 1. Batteries are old. 1. Replace the batteries. 2. Nearby lighting is too bright. 2. Install the LED Outdoor Wall Sconce in a different location or facing a different direction, away from other lighting. 3. The light is facing the wrong direction. 3. Install the LED Outdoor Wall Sconce facing the desired detection area.
PAGE 4
à piles activé par le mouvement page 4 APPLIQUE DEL EXTÉRIEURE INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT Modèle #s 43319, 44219, 46219 and 48219 À PROPOS DE VOTRE APPLIQUE DEL EXTÉRIEURE Votre Applique DEL Extérieure est parfait pour des porches, des portes, et tout au long de la maison. L’applique possède un capteur de mouvement qui allume la lumière au moment où il détecte une source de chaleur (comme des gens, des animaux ou des voitures).
PAGE 5
page 5 CHOIX DE L'EMPLACEMENT, SUITE INSTALLATION DE LA BATTERIE (CONTINUÉ) Note : Si votre Applique DEL Extérieure ne marche pas après l’installation des batteries : • Vérifiez que vous les avez insérées dans l’orientation de polarité correcte. Les batteries doivent fermement connecter avec les terminales. • Vérifiez que vous utilisez votre Applique DEL Extérieure dans une zone sombre parce qu’elle ne s’allume que dans la nuit.
PAGE 6
page 6 RÉSOLUTION DES PROBLÈMES TYPIQUES PROBLÈME CAUSE POSSIBLE SOLUTION POSSIBLE La lumière ne s’allume pas au moment où le capteur détecte les mouvements dans la zone de détection. 1. Les batteries sont vieilles. 1. Remplacez les batteries 2. L’éclairage proche est trop brillant. 2. Installez votre Applique DEL Extérieure dans un emplacement différent (l’un qui fait face dans une direction différente). La lumière s'allume sans détection du mouvement 1.