User`s manual

ManualsBrandsMaxPro ManualsBattery ChargerX6-Plus

Intelligent Charger/Discharger

6-Plus

User's Manual

INDEX

Specifications……………........................................................…......…..2

System Features……………………..............................................…....…2

Warnings……………………………......................................................……2

6-Plus charger layout…………………….....................................…….3

General Setup & Notes………………................................…….....……4

Li-Po, Li-Ion, Li-Mn, LiFePO4 Operation & Display…….…..……5

A. Li-Po, Li-Ion, Li-Mn, LiFePO4 Balance Charge..................5

B. Li-Po, Li-Ion, Li-Mn, LiFePO4 Discharge.............................6

C. Li-Po, Li-Ion, Li-Mn Storage....................................................7

D. Li-Po, Li-Ion, Li-Mn, LiFePO4 Balance.................................8

E. Li-Po, Li-Ion, Li-Mn, LiFe Cycle...............................................9

NiMH, NiCD, Pb CHG or DHG Operation & Display............10

NiMH, NiCD, Pb CYCLE Operation & Display.........................11

CT Mode for NiMH & NiCD Operation & Display..............12

Servo Test Mode Operation & Display.....................................13

POWER Mode Operation & Display..........................................14

SETUP menu Flow..........................................................................15

Error Messages................................................................................16

Warranty and Non-Warranty Service Conditions.................16

Summary of content (16 pages)

PAGE 1
Intelligent Charger/Discharger User's Manual X6-Plus INDEX Specifications……………........................................................…......…..2 System Features……………………..............................................…....…2 Warnings……………………………......................................................……2 X6-Plus charger layout…………………….....................................…….3 General Setup & Notes………………................................…….....……4 Li-Po, Li-Ion, Li-Mn, LiFePO4 Operation & Display…….…..……5 A.
PAGE 2
Thanks for purchasing Maxpro products. Pls read the User's Manual first to use your X6-Plus Specifications Input power: Charge current: Discharger current: Max. charge power: Max. discharge power: Balance charge current: Balance accuracy: Voltage tolerance: Capacity display: Supported batteries: Temperature control: PC connection: Additional functions: Weight: Size(LxWxD) 11~15V DC /15Amp (at maximum charge rate) 0.1~8.0A (0.1A/step) 0.1~3.0A (0.1A/step) 150Watt 15Watt <400mA <10mV 0.
PAGE 3
X6-Plus charger layout Check X6-Plus charger and the standard accessories you get. The following Standard items are included in the package. Conntact your supplier if missing part or damage is found.
PAGE 4
General Setup & Notes Before Charging/Discharging is started, Pls choose an appropriate AC/DC input power. When charging high voltage batteries at high current (charger output 150W) the AC/DC Power Supply should be 12V minimum with rating of 160W or more, to insure reliable performance. The X6-Plus allow you to use lower-rated power supplies reliably, but that total charger output wattage will be limited accordingly. 1. Attach X6-Plus to an appropriate DC power supply. 2.
PAGE 5
Li-Po, Li-Ion, Li-Mn, LiFePO4 Operation & Display A. Li-Po, Li-Ion, Li-Mn, LiFePO4 Balance Charge Connect the Li** Battery Main wire Connector & Balance Connector to X6-Plus No Battery 22.72V GV: 16mV> Type:LiPo 6S INC DEC <3.78 3.79 3.78 3.80 3.78 3.79 ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting within LiFe, LiPo, LiIon, LiMn. 22.72V GV: 16mV> Type:LiPo 6S Be Sure the charger is properly configured for the correct battery type.
PAGE 6
B. Li-Po, Li-Ion, Li-Mn, LiFePO4 Discharge Connect the Li** Battery Main wire Connector & Balance Connector to X6-Plus No Battery 22.72V GV: 16mV> Type:LiPo 6S INC DEC <3.78 3.79 3.78 3.80 3.78 3.79 ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting within LiFe, LiPo, LiIon, 22.72V GV: 16mV> Type:LiPo 6S LiMn. Be Sure the charger is properly configured for the correct battery type. ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting of cell numbers. 22.
PAGE 7
C. Li-Po, Li-Ion, Li-Mn Storage Connect the Li** Battery Main wire Connector & Balance Connector to X6-Plus No Battery 22.72V GV: 16mV> Type:LiPo 6S INC DEC <3.78 3.79 3.78 3.80 3.78 3.79 ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting within LiFe, LiPo, LiIon, 22.72V GV: 16mV> Type:LiPo 6S LiMn. Be Sure the charger is properly configured for the correct battery type.
PAGE 8
D. Li-Po, Li-Ion, Li-Mn, LiFePO4 Balance Connect the Li** Battery Main wire Connector & Balance Connector to X6-Plus No Battery 22.72V GV: 16mV> Type:LiPo 6S INC DEC <3.78 3.79 3.78 3.80 3.78 3.79 ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting within LiFe, LiPo, LiIon, 22.72V GV: 16mV> Type:LiPo 6S LiMn. Be Sure the charger is properly configured for the correct battery type. ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting of cell numbers. 22.
PAGE 9
E. Li-Po, Li-Ion, Li-Mn, LiFe Cycle Connect the Li** Battery Main wire Connector & Balance Connector to X6-Plus No Battery 22.72V GV: 16mV> Type:LiPo 6S INC DEC <3.78 3.79 3.78 3.80 3.78 3.79 ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting within LiFe, LiPo, LiIon, 22.72V GV: 16mV> Type:LiPo 6S LiMn. Be Sure the charger is properly configured for the correct battery type. ESC/STOP START/ENTER Press DEC & INC, Scroll through the setting of cell numbers. 22.
PAGE 10
NiMH, NiCD, Pb(Lead-Acid) CHG or DHG Operation & Display Connect the Ni** or Pb Battery Main wire Connector to X6-Plus Suggestion: Temperature sensor should be connected to X6-Plus and touched with the battery. 10.71V Type:NiMH No Battery 8S ESC/STOP START/ENTER ESC/STOP 10.71V Type:NiMH 8S ESC/STOP START/ENTER START/ENTER CHG DHG STO BAL CYCLE Choose the CHG mode CHG DHG STO BAL CYCLE Choose the DHG mode ESC/STOP ESC/STOP START/ENTER NiMH Fast CHG 8S 2500mAH 1.
PAGE 11
NiMH, NiCD, Pb(Lead-Acid) CYCLE Operation & Display Connect the Ni** or Pb Battery Main wire Connector to X6-Plus Suggestion: Temperature sensor should be connected to X6-Plus and touched with the battery. No Battery 10.71V Type:NiMH 8S ESC/STOP START/ENTER 10.71V Type:NiMH 8S ESC/STOP START/ENTER ESC/STOP CHG DHG STO BAL CYCLE ESC/STOP START/ENTER START/ENTER NiMH 8S CYCLE DHG<->CHG:1 1.1A Set the Cycle order. DHG<->CHG or CHG<->DHG ESC/STOP NiMH 8S CYCLE CHG<->DHG:1 1.
PAGE 12
ACT Mode for NiMH & NiCD Operation & Display ACT Mode can charge the NiMH or NiCD battery which voltage can't be detected by X6-Plus, It allows the user to override the voltage sensing and force the charge cycle to run. Be sure you know the battery specification & characteristic very well before you use ACT Mode. Connect the NiMH/NiCD Main wire Connector to X6-Plus. Bu sure the connection is right. If X6-Plus can't detect the voltage.
PAGE 13
Servo Test Mode Operation & Display Servo Mode can provide the Linear, Speed and the Deadband test. The servo load current should be lower than 500mA Connect the Servo to the Data port on the right side of X6-Plus.
PAGE 14
POWER Mode Operation & Display Power Mode can provide 3.0~30V adjustable DC to meet your requirement. Be sure NO equipment connect to the output socket before you choose the POWER Mode No Battery START/ENTER ACT SERVO POWER SETUP ESC/STOP START/ENTER DEC Output Set: 3.0V OUT> 3.00V 0.01A Output Set:12.8V OUT>12.80V 0.01A Press DEC/INC to Reduce/Add the output voltage (3.0~30.0V). The "OUT" value will change according to the setting. Then connect the equipment to the output socket.
PAGE 15
SETUP menu Flow Following items can be setted in SETUP menu. Key Beep ON/OFF, Buzzer ON/OFF, Temperature Cut-off, NiMH/NiCD Peak, Cycle wait time, Input power low.
PAGE 16
Error Messages Connection Break If the battery becomes disconnected during an operation. Battery Temperature Over Battery temperature is too high to be charged. Charge Capacity Over BAT INCORRECT POLARITY Bat Type Err The charged capacity reach 120% of setting capacity. Output battery is connected to the output in reverse polarity(switch +/-). Mistake the battey type for the function. Warranty and Non-Warranty Service Conditions Thanks for purchasing the products made by MAXPRO.